Category: Kenmore

How to Fix Kenmore Dishwasher Error F21
Problem: Control board memory corruption or EEPROM failure

How to Fix Dishwasher Error
1. Perform master reset by disconnecting power for 30 minutes.
2. Check all control board connections and reseat connectors.
3. Inspect board for visible damage, burned components, or bad solder joints.
4. Test backup battery on control board if equipped.
5. Replace control board assembly if memory corruption persists.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F21: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 29, 2026
How to Fix Kenmore Dryer Error F17
Problem: Thermal fuse relay failure on control board

How to Fix Dryer Error
1. Disconnect power at circuit breaker.
2. Remove control panel access cover.
3. Inspect main control board for burnt thermal fuse relay contacts.
4. Test thermal fuse operation during safety shutdown conditions.
5. Check voltage supply to thermal fuse circuit.
6. If relay is faulty, document all wire connections.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses and test thermal safety functions.
10. Run complete cycle to verify proper safety operation.
What to Check Next on This Kenmore Dryer

Kenmore Dryer Error F17: Use the code or symptom as the starting clue, then confirm what the dryer actually does before ordering parts.
1. Unplug the dryer before checking the heater, thermal fuse, thermostat, motor, belt, door switch, sensors, or control wiring.
2. Clean the lint screen and confirm strong airflow through the full vent path before replacing heat or control parts.
3. Check the door switch, drum movement, belt, rollers, moisture sensor bars, loose connectors, and signs of overheating.
4. Run a timed-dry test after airflow corrections and note whether the failure is no start, no heat, weak airflow, long dry time, or control behavior.
5. Replace a part only after the same symptom repeats and the complete Kenmore dryer model number confirms compatibility.
If the issue returns after these checks, match replacement parts to the complete Kenmore dryer model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

[OK]Thermal fuse or heater failures keep returning

[OK]Belt, roller, or motor repairs exceed unit value

[OK]Door switch or control issues stack with other faults

[OK]Older dryer has long dry times even after vent cleaning

Recommended Dryer Replacement Options

Electric Dryers

240V Vented Models

Most common electric replacement type

Confirm 3-prong vs 4-prong cord needs

Verify vent path and laundry-space depth

Shop Electric Dryers

Gas Dryers

Natural Gas Dryer Options

Confirm gas supply and shutoff location

Use qualified installation when required

Do not substitute electric for gas without planning

Compare Gas Dryers

Compact and Ventless

Small-Space Dryer Choices

Good for apartments and tight closets

Confirm ventless condensation requirements

Check capacity before replacing full-size units

View Compact Dryers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 29, 2026
How to Fix Kenmore Dishwasher Error F22
Problem: Heater relay stuck closed or failed open

How to Fix Dishwasher Error
1. Disconnect power and access control board.
2. Test heater relay contacts for proper operation.
3. Check relay coil resistance (should be 100-200 ohms).
4. Inspect relay contacts for welding or carbon buildup.
5. Test voltage to heating element when relay should be off.
6. Replace control board if relay is faulty.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F22: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 29, 2026
How to Fix Kenmore Washer Error F01
Problem: EEPROM error on main control board

How to Fix Washer Error
1. Disconnect power at circuit breaker.
2. Remove control panel access cover.
3. Inspect main control board for burnt components or damaged traces.
4. Check all wire harness connections for proper seating and corrosion.
5. Test voltage supply to control board.
6. If board shows physical damage, document all wire connections before removal.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses in correct positions.
10. Power up and run diagnostic cycle to verify operation.
As an Amazon Associate, we earn from qualifying purchases through links on this page.

Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:

For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
Browse all Kenmore error codes: Kenmore Error Codes
January 29, 2026
How to Fix Kenmore Dryer Error F16
Problem: High limit thermostat relay failure on control board

How to Fix Dryer Error
1. Disconnect power at circuit breaker.
2. Remove control panel access cover.
3. Inspect main control board for burnt high limit relay contacts.
4. Test high limit thermostat operation during overheating conditions.
5. Check voltage supply to thermostat circuit.
6. If relay is faulty, document all wire connections.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses and test high limit safety functions.
10. Run heating cycle to verify proper temperature control.
What to Check Next on This Kenmore Dryer

Kenmore Dryer Error F16: Use the code or symptom as the starting clue, then confirm what the dryer actually does before ordering parts.
1. Unplug the dryer before checking the heater, thermal fuse, thermostat, motor, belt, door switch, sensors, or control wiring.
2. Clean the lint screen and confirm strong airflow through the full vent path before replacing heat or control parts.
3. Check the door switch, drum movement, belt, rollers, moisture sensor bars, loose connectors, and signs of overheating.
4. Run a timed-dry test after airflow corrections and note whether the failure is no start, no heat, weak airflow, long dry time, or control behavior.
5. Replace a part only after the same symptom repeats and the complete Kenmore dryer model number confirms compatibility.
If the issue returns after these checks, match replacement parts to the complete Kenmore dryer model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

[OK]Thermal fuse or heater failures keep returning

[OK]Belt, roller, or motor repairs exceed unit value

[OK]Door switch or control issues stack with other faults

[OK]Older dryer has long dry times even after vent cleaning

Recommended Dryer Replacement Options

Electric Dryers

240V Vented Models

Most common electric replacement type

Confirm 3-prong vs 4-prong cord needs

Verify vent path and laundry-space depth

Shop Electric Dryers

Gas Dryers

Natural Gas Dryer Options

Confirm gas supply and shutoff location

Use qualified installation when required

Do not substitute electric for gas without planning

Compare Gas Dryers

Compact and Ventless

Small-Space Dryer Choices

Good for apartments and tight closets

Confirm ventless condensation requirements

Check capacity before replacing full-size units

View Compact Dryers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 29, 2026
How to Fix Kenmore Dryer Error F15
Problem: Flame sensor relay failure on control board

How to Fix Dryer Error
1. Turn off power and gas supply to dryer.
2. Remove control panel access cover.
3. Inspect main control board for burnt flame sensor relay contacts.
4. Test flame sensor operation during combustion.
5. Check voltage supply to flame sensor circuit.
6. If relay is faulty, document all wire connections.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses and restore gas supply.
10. Test flame detection and safety shutdown functions.
What to Check Next on This Kenmore Dryer

Kenmore Dryer Error F15: Use the code or symptom as the starting clue, then confirm what the dryer actually does before ordering parts.
1. Unplug the dryer before checking the heater, thermal fuse, thermostat, motor, belt, door switch, sensors, or control wiring.
2. Clean the lint screen and confirm strong airflow through the full vent path before replacing heat or control parts.
3. Check the door switch, drum movement, belt, rollers, moisture sensor bars, loose connectors, and signs of overheating.
4. Run a timed-dry test after airflow corrections and note whether the failure is no start, no heat, weak airflow, long dry time, or control behavior.
5. Replace a part only after the same symptom repeats and the complete Kenmore dryer model number confirms compatibility.
If the issue returns after these checks, match replacement parts to the complete Kenmore dryer model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

[OK]Thermal fuse or heater failures keep returning

[OK]Belt, roller, or motor repairs exceed unit value

[OK]Door switch or control issues stack with other faults

[OK]Older dryer has long dry times even after vent cleaning

Recommended Dryer Replacement Options

Electric Dryers

240V Vented Models

Most common electric replacement type

Confirm 3-prong vs 4-prong cord needs

Verify vent path and laundry-space depth

Shop Electric Dryers

Gas Dryers

Natural Gas Dryer Options

Confirm gas supply and shutoff location

Use qualified installation when required

Do not substitute electric for gas without planning

Compare Gas Dryers

Compact and Ventless

Small-Space Dryer Choices

Good for apartments and tight closets

Confirm ventless condensation requirements

Check capacity before replacing full-size units

View Compact Dryers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 29, 2026
How to Fix Kenmore Dryer Error F14
Problem: Gas valve relay failure on control board

How to Fix Dryer Error
1. Turn off power and gas supply to dryer.
2. Remove control panel access cover.
3. Inspect main control board for burnt gas valve relay contacts.
4. Test gas valve operation during ignition sequence.
5. Check voltage supply to gas valve circuit.
6. If relay is faulty, document all wire connections.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses and restore gas supply.
10. Test gas valve operation and flame safety functions.
What to Check Next on This Kenmore Dryer

Kenmore Dryer Error F14: Use the code or symptom as the starting clue, then confirm what the dryer actually does before ordering parts.
1. Unplug the dryer before checking the heater, thermal fuse, thermostat, motor, belt, door switch, sensors, or control wiring.
2. Clean the lint screen and confirm strong airflow through the full vent path before replacing heat or control parts.
3. Check the door switch, drum movement, belt, rollers, moisture sensor bars, loose connectors, and signs of overheating.
4. Run a timed-dry test after airflow corrections and note whether the failure is no start, no heat, weak airflow, long dry time, or control behavior.
5. Replace a part only after the same symptom repeats and the complete Kenmore dryer model number confirms compatibility.
If the issue returns after these checks, match replacement parts to the complete Kenmore dryer model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

[OK]Thermal fuse or heater failures keep returning

[OK]Belt, roller, or motor repairs exceed unit value

[OK]Door switch or control issues stack with other faults

[OK]Older dryer has long dry times even after vent cleaning

Recommended Dryer Replacement Options

Electric Dryers

240V Vented Models

Most common electric replacement type

Confirm 3-prong vs 4-prong cord needs

Verify vent path and laundry-space depth

Shop Electric Dryers

Gas Dryers

Natural Gas Dryer Options

Confirm gas supply and shutoff location

Use qualified installation when required

Do not substitute electric for gas without planning

Compare Gas Dryers

Compact and Ventless

Small-Space Dryer Choices

Good for apartments and tight closets

Confirm ventless condensation requirements

Check capacity before replacing full-size units

View Compact Dryers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 28, 2026
How to Fix Kenmore Dishwasher Error F23
Problem: Pressure switch stuck or out of calibration

How to Fix Dishwasher Error
1. Disconnect pressure switch hose and blow through it to clear blockages.
2. Test pressure switch operation with multimeter while applying air pressure.
3. Check pressure switch mounting and alignment.
4. Verify pressure switch calibration against specifications.
5. Replace pressure switch if it doesn’t switch at correct pressure levels.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F23: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 28, 2026
How to Fix Kenmore Dishwasher Error F24
Problem: Flow meter malfunction or incorrect water measurement

How to Fix Dishwasher Error
1. Access flow meter assembly and check for debris.
2. Inspect impeller for free rotation and damage.
3. Test flow meter sensor output with multimeter during water flow.
4. Check flow meter wiring harness for damage.
5. Verify flow meter calibration against actual water usage.
6. Replace flow meter assembly if readings are inaccurate.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F24: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 28, 2026
How to Fix Kenmore Dryer Error F13
Problem: Igniter relay failure on gas dryer control board

How to Fix Dryer Error
1. Turn off power and gas supply to dryer.
2. Remove control panel access cover.
3. Inspect main control board for burnt igniter relay contacts.
4. Test igniter operation during heating cycle start.
5. Check voltage supply to igniter circuit.
6. If relay is faulty, document all wire connections.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses and restore gas supply.
10. Test ignition sequence and flame operation.
What to Check Next on This Kenmore Dryer

Kenmore Dryer Error F13: Use the code or symptom as the starting clue, then confirm what the dryer actually does before ordering parts.
1. Unplug the dryer before checking the heater, thermal fuse, thermostat, motor, belt, door switch, sensors, or control wiring.
2. Clean the lint screen and confirm strong airflow through the full vent path before replacing heat or control parts.
3. Check the door switch, drum movement, belt, rollers, moisture sensor bars, loose connectors, and signs of overheating.
4. Run a timed-dry test after airflow corrections and note whether the failure is no start, no heat, weak airflow, long dry time, or control behavior.
5. Replace a part only after the same symptom repeats and the complete Kenmore dryer model number confirms compatibility.
If the issue returns after these checks, match replacement parts to the complete Kenmore dryer model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

[OK]Thermal fuse or heater failures keep returning

[OK]Belt, roller, or motor repairs exceed unit value

[OK]Door switch or control issues stack with other faults

[OK]Older dryer has long dry times even after vent cleaning

Recommended Dryer Replacement Options

Electric Dryers

240V Vented Models

Most common electric replacement type

Confirm 3-prong vs 4-prong cord needs

Verify vent path and laundry-space depth

Shop Electric Dryers

Gas Dryers

Natural Gas Dryer Options

Confirm gas supply and shutoff location

Use qualified installation when required

Do not substitute electric for gas without planning

Compare Gas Dryers

Compact and Ventless

Small-Space Dryer Choices

Good for apartments and tight closets

Confirm ventless condensation requirements

Check capacity before replacing full-size units

View Compact Dryers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
January 28, 2026