Category: Kenmore

  • How to Fix Kenmore Dryer Error F72

    How to Fix Kenmore Dryer Error F72

    Problem: User interface display failure

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel faceplate and access cover.
    3. Inspect display connections for loose or corroded connectors.
    4. Test display backlight and segment operation.
    5. Check ribbon cable connections between display and interface board.
    6. Clean electrical contacts with contact cleaner.
    7. If display is faulty, disconnect ribbon cable.
    8. Remove mounting screws and replace display assembly.
    9. Reconnect ribbon cable and test display functions.
    10. Run diagnostic mode to verify proper display operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F05

    How to Fix Kenmore Dishwasher Error F05

    Problem: Overfill condition detected by float switch

    How to Fix Dishwasher Error

    1. Check float switch assembly for proper movement and continuity.
    2. Inspect drain system for blockages causing backup.
    3. Test overfill protection switch operation.
    4. Verify drain pump is functioning correctly.
    5. Replace control board if sensors test good but error persists.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F15

    How to Fix Kenmore Washer Error F15

    Problem: Motor control unit error – communication failure

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove front access panel and motor control board cover.
    3. Inspect motor control board connectors for corrosion or damage.
    4. Check wiring harness between motor control and main control boards.
    5. Test communication signals with multimeter if possible.
    6. Clean all electrical contacts with contact cleaner.
    7. If connections are good but error persists, replace motor control board.
    8. Document all wire connections before disconnecting.
    9. Install new motor control board assembly.
    10. Test motor operation and communication with main control board.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F06

    How to Fix Kenmore Dishwasher Error F06

    Problem: Motor control unit (MCU) communication failure

    How to Fix Dishwasher Error

    1. Reset control board by disconnecting power for 15 minutes.
    2. Check all motor harness connections for corrosion or damage.
    3. Test motor windings for proper resistance values.
    4. Inspect MCU board for burned components or bad solder joints.
    5. Replace MCU board if communication cannot be restored.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F71

    How to Fix Kenmore Dryer Error F71

    Problem: User interface keypad failure

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove control panel faceplate and access cover.
    3. Inspect membrane switch pad for physical damage or debris.
    4. Test each button contact with multimeter for proper continuity.
    5. Clean button contacts with electrical contact cleaner and soft brush.
    6. If membrane switch is damaged, disconnect ribbon cable from control board.
    7. Remove mounting screws and replace entire control panel assembly.
    8. Reconnect ribbon cable and test all button functions.
    9. Clear error code by cycling power and verify operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F07

    How to Fix Kenmore Dishwasher Error F07

    Problem: Water fill timeout or insufficient water pressure

    How to Fix Dishwasher Error

    1. Verify home water pressure is adequate (minimum 20 PSI).
    2. Check water supply valve is fully open.
    3. Inspect inlet valve screen for mineral deposits or debris.
    4. Test flow meter operation during fill cycle.
    5. Replace water inlet valve if flow is restricted.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F14

    How to Fix Kenmore Washer Error F14

    Problem: EEPROM error on control board

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel access cover.
    3. Inspect main control board for physical damage.
    4. Check all wire harness connections for proper seating.
    5. Test voltage supply to control board.
    6. If board appears undamaged, attempt to reset by disconnecting power for 10 minutes.
    7. If error persists, document all wire connections before removal.
    8. Remove mounting screws and disconnect all connectors.
    9. Install new main control board assembly.
    10. Reconnect all harnesses and run diagnostic cycle to verify operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F08

    How to Fix Kenmore Dishwasher Error F08

    Problem: Heater circuit failure or open heating element

    How to Fix Dishwasher Error

    1. Disconnect power and access heating element.
    2. Test element for continuity (should read 8-20 ohms).
    3. Check high-limit thermostat for proper operation.
    4. Inspect wiring harness for damage or loose connections.
    5. Test control board heater relay contacts.
    6. Replace faulty component.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F70

    How to Fix Kenmore Dryer Error F70

    Problem: User interface communication failure

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel faceplate and access cover.
    3. Inspect user interface board connectors for corrosion or damage.
    4. Check ribbon cable connections between interface and main control.
    5. Test communication signals with multimeter if possible.
    6. Clean all electrical contacts with contact cleaner.
    7. If connections are good but error persists, replace user interface board.
    8. Document all wire connections before disconnecting.
    9. Install new user interface board assembly.
    10. Test all button functions and display operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F13

    How to Fix Kenmore Washer Error F13

    Problem: Dispenser circuit error – detergent dispenser malfunction

    How to Fix Washer Error

    1. Turn off power supply.
    2. Remove dispenser drawer and clean thoroughly.
    3. Inspect dispenser housing for debris or mechanical binding.
    4. Locate dispenser solenoid or wax motor assembly.
    5. Test dispenser motor resistance with multimeter.
    6. Check electrical connections for corrosion or damage.
    7. If dispenser mechanism is faulty, remove mounting screws.
    8. Replace entire dispenser assembly or individual solenoid.
    9. Reinstall dispenser drawer and test operation.
    10. Run diagnostic cycle to verify dispenser timing and function.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes