Category: Frigidaire

  • How to Fix Frigidaire Washer Error E57

    How to Fix Frigidaire Washer Error E57

    Error Code: E57 Difficulty: Hard

    Problem: High current on inverter.

    How to Fix E57 Error (Step-by-Step)

    1. Turn off the circuit breaker for the washer and unplug it from the wall outlet.
    2. Remove the rear access panel of the washer to locate the motor control board (inverter), which is situated near the bottom of the machine.
    3. Take a clear photo of the wire connections to the board for reference before disconnecting anything.
    4. Carefully disconnect all wire harnesses leading to the motor control board.
    5. Remove the mounting screws that hold the control board in place and lift the old board out of the washer.
    6. Install the new motor control board, securing it with the mounting screws.
    7. Reconnect all wire harnesses according to your reference photo, reattach the access panel, and restore power to test the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E56

    How to Fix Frigidaire Washer Error E56

    Error Code: E56 Difficulty: Hard

    Problem: High motor current.

    How to Fix E56 Error (Step-by-Step)

    1. Disconnect the washer from its power source by unplugging the cord from the wall.
    2. Access the bottom of the washer, which may require carefully tilting the machine back and propping it up securely.
    3. Locate the drive motor and the motor control board. Visually inspect both for burn marks, melted connectors, or damaged wires.
    4. Ensure the wire harness connecting the motor to the control board is securely plugged in at both ends.
    5. A professional would use a multimeter to test the motor windings for continuity. If the motor fails the test, it requires replacement.
    6. If the motor tests good, the failure is likely in the motor control board, which will need to be replaced.
    7. After replacing the faulty component (either the motor or the control board), reassemble the washer and test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134743500 (Motor Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E4A

    How to Fix Frigidaire Washer Error E4A

    Error Code: E4A Difficulty: Moderate

    Problem: Control detects a problem with the door lock circuit.

    How to Fix E4A Error (Step-by-Step)

    1. Unplug the washer from the power outlet to prevent electrical shock.
    2. Open the washer door. Use a screwdriver to pry off the outer spring clamp that holds the rubber door boot seal to the front panel.
    3. Peel the door boot away from the front panel around the door lock area to gain access to the lock assembly.
    4. Disconnect the electrical wire connector from the door lock assembly.
    5. Remove the screws that mount the door lock assembly to the washer’s front panel and take out the old part.
    6. Install the new door lock assembly, secure it with the mounting screws, and reconnect the wire harness.
    7. Re-secure the door boot seal with the spring clamp, plug in the washer, and test the door lock.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E4

    How to Fix Frigidaire Washer Error E4

    Error Code: E4 Difficulty: Easy

    Problem: The washer is out of balance.

    How to Fix E4 Error (Step-by-Step)

    1. Press the pause button to stop the cycle and wait for the door to unlock.
    2. Open the door and redistribute the laundry load, moving items around so they are spread evenly inside the drum.
    3. Avoid washing single heavy items, like a bath mat, by themselves. Add a few towels to balance the load.
    4. Check if the washer is level by placing a bubble level on top of the machine. Check front-to-back and side-to-side.
    5. Adjust the washer’s leveling feet at each corner by screwing them up or down until the machine is stable and level.
    6. Tighten the lock nuts on the leveling feet against the base of the washer to secure them in place.
    7. Close the door and resume the wash cycle and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E32

    How to Fix Frigidaire Washer Error E32

    Error Code: E32 Difficulty: Moderate

    Problem: Water level pressure sensor isn’t communicating with the electronic control board or there is a pressure sensor calibration problem.

    How to Fix E32 Error (Step-by-Step)

    1. Disconnect the washer from the wall outlet to ensure your safety during the repair.
    2. To access the internal components, you will typically need to remove the top panel of the washer by unscrewing fasteners at the back.
    3. Locate the water level pressure sensor; it is a small, round part with a thin air hose and a wire connector attached.
    4. Carefully disconnect the wire harness by pressing its release tab and pull the thin rubber air hose off the sensor’s port.
    5. Remove the screw or release the clip holding the sensor to the washer’s chassis and remove the old sensor.
    6. Mount the new pressure sensor, then firmly reconnect the air hose and the electrical wire harness.
    7. Reinstall the top panel, plug the washer in, and run a test cycle to confirm the fix.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E3

    How to Fix Frigidaire Washer Error E3

    Error Code: E3 Difficulty: Easy

    Problem: The lid is open or there is a door lock problem.

    How to Fix E3 Error (Step-by-Step)

    1. Open the washer door and then close it again, pushing firmly to ensure it is securely latched.
    2. Listen for a distinct ‘click’ sound which indicates the door lock has engaged properly.
    3. Inspect the area around the door lock mechanism for any obstructions like fabric from clothing, lint buildup, or dirt.
    4. Use a damp cloth to wipe down the door, the rubber seal, and the lock assembly to ensure a clean contact surface.
    5. As a reset, unplug the washer from the electrical outlet for five minutes.
    6. Plug the washer back in and attempt to start a new cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E2

    How to Fix Frigidaire Washer Error E2

    Error Code: E2 Difficulty: Easy

    Problem: The washer is not draining.

    How to Fix E2 Error (Step-by-Step)

    1. Examine the drain hose behind the washer to ensure it is not kinked, clogged, or improperly positioned.
    2. Confirm the end of the drain hose is no more than 8 inches into the standpipe or laundry sink to prevent siphoning.
    3. Locate the drain pump filter access door, typically on the bottom front of the washer.
    4. Place a shallow pan and towels underneath the access door to catch water before twisting the filter cap counter-clockwise.
    5. Slowly remove the filter and clean it of any lint, coins, hair, or other foreign objects that may be causing a blockage.
    6. Securely screw the filter back into place, ensuring a tight seal to prevent leaks.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Frigidaire Washer Error E1

    How to Fix Frigidaire Washer Error E1

    Error Code: E1 Difficulty: Easy

    Problem: Water is not entering the washer or the fill time is slow.

    How to Fix E1 Error (Step-by-Step)

    1. Verify that both the hot and cold water faucets supplying the washer are turned on completely.
    2. Inspect the full length of the water inlet hoses for any kinks, twists, or crushing that could restrict water flow and straighten them.
    3. Turn off the water supply faucets and unscrew the inlet hoses from the back of the washer.
    4. Check the small metal filter screens inside the washer’s water inlet ports for any sediment or debris.
    5. Use a small brush or pliers to gently remove the screens and rinse them thoroughly under clean water until all debris is gone.
    6. Reinstall the filter screens, securely reconnect the hoses, and turn the water faucets back on.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.