Category: Frigidaire

How to Fix Frigidaire Washer Error E5A
Error Code: E5A Difficulty: Hard

Problem: High temperature on the heat sink.

How to Fix E5A Error (Step-by-Step)
1. Disconnect the washer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Remove the rear access panel of the washer by taking out the screws holding it in place.
3. Locate the motor control board, which is a circuit board situated near the main drive motor at the bottom of the machine.
4. Take a clear photo of the wire connections before proceeding.
5. Disconnect all wire harnesses from the board. They are secured with locking tabs.
6. Remove the screws mounting the board to the washer’s frame and install the new board.
7. Reconnect the wires using your photo as a guide, then replace the rear panel.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E55
Error Code: E55 Difficulty: Hard

Problem: Motor overheating or an issue with the water temperature sensor.

How to Fix E55 Error (Step-by-Step)
1. Unplug the washer and turn off the water supply. Disconnect the hoses.
2. Carefully lay the washer on its back on a soft surface like a blanket to access the bottom.
3. Locate the drive motor. First, remove the drive belt by walking it off the large pulley.
4. Disconnect the wire harness connected to the motor and confirm the error stays cleared during a full test cycle.
5. Remove the bolts that mount the motor to the washer’s base.
6. Install the new motor, secure it with the mounting bolts, and reconnect the wire harness.
7. Reinstall the drive belt, carefully return the washer to an upright position, and reconnect all hoses and power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E48
Error Code: E48 Difficulty: Moderate

Problem: The control board thinks the door PTC circuit is closed.

How to Fix E48 Error (Step-by-Step)
1. Unplug the washer from the wall for safety and confirm the error stays cleared during a full test cycle.
2. Open the door and locate the metal or plastic clamp ring on the outside of the rubber door seal. Use pliers to expand and remove this clamp.
3. Fold the rubber door seal back into the drum to access the door lock assembly.
4. Unscrew the two screws holding the door lock assembly to the front panel of the washer.
5. Disconnect the wiring harness from the back of the old lock assembly.
6. Connect the new lock assembly to the wiring harness and secure it to the front panel with the screws.
7. Re-secure the rubber door seal with the clamp, ensuring it is evenly seated.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E47
Error Code: E47 Difficulty: Moderate

Problem: The control board thinks the door PTC circuit is open in spin.

How to Fix E47 Error (Step-by-Step)
1. Disconnect the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
2. Open the washer door and locate the flexible rubber boot. Find the spring clamp that holds it to the front panel.
3. Carefully pry off the spring clamp and peel the boot away from the door opening, exposing the door lock assembly.
4. Remove the screws that attach the door lock to the washer’s chassis.
5. Pull the lock assembly out and disconnect the electrical plug attached to it.
6. Attach the electrical plug to the new door lock assembly.
7. Screw the new assembly into place, then carefully work the rubber boot and spring clamp back into their original positions.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E46
Error Code: E46 Difficulty: Hard

Problem: Control board problem.

How to Fix E46 Error (Step-by-Step)
1. Unplug the washing machine to ensure safety and confirm the error stays cleared during a full test cycle.
2. Remove the top panel by taking out the screws located on the back of the washer.
3. Find the main control board inside a plastic housing. Take a photo of the wire layout for later reference.
4. Disconnect the multiple wire harnesses attached to the board by releasing their locking tabs.
5. Unfasten the screws or clips holding the control board and its housing.
6. Replace the old board with the new one, making sure it snaps securely into place.
7. Use your photo to reconnect all wires, then screw the top panel back on and plug in the machine.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E45
Error Code: E45 Difficulty: Hard

Problem: Control board problem or problem with the door lock circuit.

How to Fix E45 Error (Step-by-Step)
1. Ensure the washer is completely disconnected from power and confirm the error stays cleared during a full test cycle.
2. Remove the top cover of the washer to gain access to the internal components.
3. Locate the main control board, easily identified by the large number of wires connected to it.
4. Take a picture of the board and its connections to ensure you can reconnect everything correctly.
5. Disconnect all the wire harnesses from the board. These have small clips that must be depressed to release.
6. Remove the board from its mountings, which may be screws or plastic clips.
7. Install the new board, reconnect the wires precisely, and then secure the top panel before restoring power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E44
Error Code: E44 Difficulty: Hard

Problem: Control board problem.

How to Fix E44 Error (Step-by-Step)
1. Unplug the washer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Remove the top panel of the appliance by unscrewing it from the rear.
3. Locate the main control board. Before touching it, take a clear photograph of the wiring for reference during reassembly.
4. Carefully press the locking tabs on each wire connector and pull to disconnect them from the board.
5. Remove the screws or release the plastic tabs that hold the control board housing in place.
6. Swap the old board with the new one, ensuring it is properly seated.
7. Reconnect all wiring harnesses as per your photo, then reinstall the top panel and plug the washer in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E43
Error Code: E43 Difficulty: Moderate

Problem: Control board problem or problem with the door lock circuit.

How to Fix E43 Error (Step-by-Step)
1. Disconnect the washer from its power source and confirm the error stays cleared during a full test cycle.
2. Use a pair of pliers or a spring removal tool to take off the outer clamp securing the door bellows to the front of the washer.
3. Gently peel back the rubber bellows around the door lock mechanism to get access.
4. Unscrew the two screws holding the door lock assembly in place.
5. Maneuver the old lock out through the opening and disconnect its electrical connector.
6. Plug the electrical connector into the new door lock assembly and position it correctly.
7. Secure the new lock with its screws, reinstall the door bellows and clamp, and then restore power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E42
Error Code: E42 Difficulty: Moderate

Problem: The door remains locked after the cycle is completed.

How to Fix E42 Error (Step-by-Step)
1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Open the washer door. Use a spring-expansion tool or pliers to expand and remove the outer wire clamp holding the rubber door boot (bellows) to the front panel.
3. Peel the door boot away from the front panel in the area of the door lock assembly.
4. Remove the screws that secure the door lock assembly to the washer’s frame.
5. Reach inside and disconnect the wire harness from the old door lock assembly.
6. Connect the wire harness to the new assembly, then mount the new assembly to the frame with the screws.
7. Re-seat the rubber door boot and secure it with the wire clamp before plugging the washer in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E38
Error Code: E38 Difficulty: Easy

Problem: Clogged air trap.

How to Fix E38 Error (Step-by-Step)
1. Unplug the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
2. Pull the washer away from the wall to access the back panel.
3. Remove the top panel by taking out the screws along the back edge.
4. Locate the pressure switch, which is a round component with a thin rubber or plastic hose attached to it.
5. Disconnect the hose from the pressure switch port and confirm the error stays cleared during a full test cycle.
6. Blow firmly through the hose to clear any trapped lint, soap scum, or debris.
7. Reconnect the hose securely to the pressure switch, replace the top panel, and plug the washer in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026