Category: Washer

  • How to Fix Electrolux Washer Error 9E

    How to Fix Electrolux Washer Error 9E

    Error Code: 9E Difficulty: Moderate

    Problem: Touch sensor on the user interface is not responding.

    How to Fix 9E Error (Step-by-Step)

    1. Disconnect the washer from the power source to ensure safety.
    2. Remove the top panel of the washer by unscrewing the screws at the back.
    3. Locate the user interface control board, which is typically situated at the front of the washer.
    4. Carefully disconnect the wire connectors attached to the control board.
    5. Remove the screws that are holding the control board in place and then remove the old board.
    6. Install the new user interface control board (part 137007000) and secure it with the screws.
    7. Reconnect all the wire connectors, reattach the top panel, and plug the washer back in to test the new interface.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error SUDS

    How to Fix Electrolux Washer Error SUDS

    Error Code: SUDS Difficulty: Easy

    Problem: Too many suds detected.

    How to Fix SUDS Error (Step-by-Step)

    1. Pause the current wash cycle if the machine has not already stopped automatically.
    2. Do not add any more water or detergent. Allow the washer to sit for 30-60 minutes to allow the suds to break down on their own.
    3. After the waiting period, select a ‘Rinse & Spin’ or ‘Drain & Spin’ cycle to clear out the excess foam.
    4. Once the cycle is complete and the suds are gone, you can restart your laundry.
    5. To prevent this in the future, ensure you are using a High-Efficiency (HE) detergent, which is specifically designed for low-water washing machines.
    6. Measure your detergent carefully according to the manufacturer’s instructions for your load size and water hardness. Overdosing is the primary cause of excess suds.
    7. Consider using less detergent for smaller or lightly soiled loads.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error LOC

    How to Fix Electrolux Washer Error LOC

    Error Code: LOC Difficulty: Easy

    Problem: Control lock activated.

    How to Fix LOC Error (Step-by-Step)

    1. Locate the ‘Control Lock’ button on your washer’s control panel. It may be a standalone button or a secondary function of another button.
    2. Press and hold the ‘Control Lock’ button for 3 to 5 seconds.
    3. Observe the display panel; the lock symbol or ‘LOC’ message should disappear, indicating the controls are unlocked.
    4. If your model does not have a dedicated ‘Control Lock’ button, it is often a combination of two buttons that need to be pressed simultaneously.
    5. Look for two buttons with a small lock icon between or below them.
    6. Press and hold these two buttons at the same time for 3 to 5 seconds to deactivate the lock.
    7. Test the controls by attempting to select a cycle or change a setting.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error HO SE

    How to Fix Electrolux Washer Error HO SE

    Error Code: HO SE Difficulty: Easy

    Problem: Reversed hot and cold water hoses.

    How to Fix HO SE Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Turn off both the hot and cold water supply valves completely.
    3. Carefully unscrew the water inlet hoses from the back of the washing machine.
    4. Inspect the hose connections on the washer; they are typically color-coded, with red for hot and blue for cold.
    5. Reconnect the hose from the hot water supply to the red (hot) inlet and the hose from the cold water supply to the blue (cold) inlet.
    6. Hand-tighten the connections first, then use pliers to give them a gentle quarter-turn to ensure they are secure.
    7. Turn the water supply valves back on, plug in the washer, and run a test cycle to check for leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error EF3

    How to Fix Electrolux Washer Error EF3

    Error Code: EF3 Difficulty: Easy

    Problem: Aquastop system activated.

    How to Fix EF3 Error (Step-by-Step)

    1. Immediately turn off the water supply to the washer from the wall valves.
    2. Unplug the washing machine from the electrical outlet and confirm the error stays cleared during a full test cycle.
    3. Carefully pull the washer away from the wall to inspect the water inlet hoses for any visible leaks or damage. Tighten any loose connections.
    4. Check the base of the machine for any pooled water. If water is present, it indicates a leak that has triggered the Aquastop system.
    5. Tilt the machine slightly forward to allow any water in the base pan to drain out, which should reset the Aquastop float switch.
    6. Once the area is dry and you’ve addressed any visible leaks, you can restore the power and water supply.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error EF2

    How to Fix Electrolux Washer Error EF2

    Error Code: EF2 Difficulty: Easy

    Problem: There is too much foam in the drum.

    How to Fix EF2 Error (Step-by-Step)

    1. Press the pause or cancel button to stop the current cycle.
    2. Wait for the washer to drain and the door to unlock. If it doesn’t, you may need to run a drain/spin cycle.
    3. Remove the clothes from the drum and confirm the error stays cleared during a full test cycle.
    4. Run a full wash cycle without any laundry or detergent on the hottest water setting to flush out any residual suds.
    5. For future washes, ensure you are using a high-efficiency (HE) detergent, as regular detergents produce too many suds for these machines.
    6. Measure your detergent carefully according to the manufacturer’s instructions for your load size and water hardness.
    7. If you have soft water, you will need to use significantly less detergent.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error EF0

    How to Fix Electrolux Washer Error EF0

    Error Code: EF0 Difficulty: Easy

    Problem: Water Leakage / Suds / Blocked Filter – General error for water leakage, excessive suds, or a blocked filter.

    How to Fix EF0 Error (Step-by-Step)

    1. First, cancel the current wash cycle and turn off the washer.
    2. Check around and under the washer for any signs of water leakage. If you see water, unplug the machine and soak up the water before proceeding.
    3. Locate the small door on the bottom front of the washer; this is the filter access panel. Place a shallow pan and a towel in front of it to catch any residual water.
    4. Open the panel and slowly unscrew the filter cap, allowing the water to drain into the pan. Once drained, completely remove the filter.
    5. Clean the filter of any lint, hair, or debris. Also, check the filter housing for any foreign objects and remove them.
    6. Re-insert the clean filter and screw the cap on tightly. Close the access panel.
    7. If the issue was excessive suds, run a rinse and spin cycle with no clothes or detergent to clear out the excess foam.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error DN

    How to Fix Electrolux Washer Error DN

    Error Code: DN Difficulty: Easy

    Problem: Demo mode is activated.

    How to Fix DN Error (Step-by-Step)

    1. Press and hold the ‘Temp’ and ‘Spin’ buttons simultaneously for 5-7 seconds.
    2. The display should change from ‘dn’ to show a regular cycle time.
    3. If this does not work, try pressing and holding the ‘Power’ and ‘Start/Pause’ buttons together for a few seconds.
    4. Some models may require you to press and hold the ‘Soil’ and ‘Spin’ buttons.
    5. Once demo mode is deactivated, the washer will resume normal operation.
    6. Run a short cycle to confirm the washer is functioning correctly.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes