Category: Washer

Error Code: F44 Difficulty: Hard

Problem: No motor rotation.

How to Fix F44 Error (Step-by-Step)

1. Ensure the washer is unplugged from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Remove the back panel of the washer to expose the motor.
3. Locate the carbon brushes on the motor assembly and confirm the error stays cleared during a full test cycle.
4. Disconnect the electrical connectors attached to the brushes and confirm the error stays cleared during a full test cycle.
5. Unscrew or unclip the brush holders to remove the worn carbon brushes.
6. Insert the new carbon brushes into the holders, ensuring they make good contact with the motor’s commutator.
7. Re-secure the brush holders and reconnect the electrical connectors and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F59 Difficulty: Hard

Problem: 3D sensor: measurement error too high or too low.

How to Fix F59 Error (Step-by-Step)

1. Disconnect the washer from power and confirm the error stays cleared during a full test cycle.
2. Access the 3D sensor, usually located on the tub and confirm the error stays cleared during a full test cycle.
3. Check the wiring between the 3D sensor and the control board for any damage or loose connections.
4. If the wiring is intact, replace the 3D sensor and confirm the error stays cleared during a full test cycle.
5. If the error persists after replacing the sensor, the control board may be faulty and require replacement.
6. To replace the control board, carefully label and disconnect all wire harnesses.
7. Remove the old board, install the new one, and reconnect all harnesses.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F60 Difficulty: Hard

Problem: Flow sensor or pressure sensor error.

How to Fix F60 Error (Step-by-Step)

1. Disconnect the washer from power and water sources. Turn off the water supply valves and unplug the power cord from the wall outlet.
2. Remove the top panel of the washer to access the internal components. This is typically held in place by screws at the back.
3. Locate the water inlet valve at the back of the machine where the water hoses connect. Disconnect the wire harnesses and hoses, then remove the screws holding it in place and replace it with the new valve.
4. The pressure sensor is usually connected to the control board via a small tube. Inspect the tube for any blockages or damage and clear or replace it as necessary.
5. To replace the control board, carefully label and disconnect all wire harnesses connected to it. Remove the mounting screws and gently lift the old board out.
6. Install the new control board, ensuring all wire harnesses are securely reconnected to their correct terminals. Re-secure the top panel.
7. Reconnect the water hoses and power cord. Turn the water supply on and run a test cycle to ensure the error is cleared.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F63 Difficulty: Hard

Problem: Software error.

How to Fix F63 Error (Step-by-Step)

1. Turn off the circuit breaker for the washer and unplug it from the wall for safety.
2. Remove the top panel of the washing machine by unscrewing the screws at the back.
3. Locate the main control board, which is typically housed in a plastic casing.
4. Take a photo of the wire connections to the control board to ensure you reconnect them correctly. Carefully disconnect all the wiring harnesses.
5. Remove the screws or release the tabs holding the control board in place and carefully remove the old board.
6. Install the new control board, making sure it is securely mounted. Reconnect all the wiring harnesses according to your photo.
7. Replace the top panel and screw it back into place. Restore power to the washer and run a check cycle to check if the software error is resolved.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F67 Difficulty: Hard

Problem: Card error.

How to Fix F67 Error (Step-by-Step)

1. Disconnect the washer from its power source by unplugging it from the wall outlet.
2. Remove the top panel of the washer to gain access to the internal components. This usually involves removing a few screws from the back.
3. Identify the main control board. It is often located in a protective plastic housing.
4. Before disconnecting any wires, take a clear picture to remember their placement. Proceed to disconnect all electrical connectors from the control board.
5. Unfasten the screws or clips that hold the control board in its housing and carefully take out the old board.
6. Place the new control board into the housing and secure it with the screws or clips. Reconnect all the wires as they were originally.
7. Put the top panel back on and secure it. Plug the washer back in and start a cycle to confirm that the card error is gone.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Get the Washer Error Code Guide: https://appliancewhisperer.gumroad.com/l/sirmci

Error Code: FOAM DETECTION SYMBOL Difficulty: Easy

Problem: Too much foam has been detected during the wash cycle.

How to Fix FOAM DETECTION SYMBOL Error (Step-by-Step)

1. Pause the current wash cycle. If the machine will not pause, turn it off.
2. Wait for 15-20 minutes to allow the foam to dissipate on its own.
3. Once the foam has reduced, select a ‘Rinse’ or ‘Spin’ cycle and run it without adding any more detergent. This will help to flush out the excess suds.
4. If there is still a lot of foam, you may need to run an additional rinse cycle.
5. To prevent this in the future, reduce the amount of detergent you are using, especially for smaller or lightly soiled loads.
6. Ensure you are using a high-efficiency (HE) detergent, as these are formulated to produce fewer suds.
7. If you have soft water, you will need to use significantly less detergent than the manufacturer’s recommendation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.