Category: Washer

  • How to Fix Bosch Washer Error E23

    How to Fix Bosch Washer Error E23

    Error Code: E23 Difficulty: Easy

    Problem: AquaStop Hose has been activated; indicates a leak.

    How to Fix E23 Error (Step-by-Step)

    1. Unplug the washing machine from the power source immediately and confirm the error stays cleared during a full test cycle.
    2. Turn off the water supply to the washer at the wall valves.
    3. Inspect the base of the machine for any visible signs of water leakage.
    4. Check the AquaStop hose connections at both the tap and the machine to ensure they are tight.
    5. Tilt the machine slightly to drain any water that may have collected in the base pan, which can trigger the sensor.
    6. After ensuring there are no active leaks and the base is dry, plug the machine back in and turn on the water supply.
    7. Run a short test cycle to confirm the error is cleared and no new leaks appear.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E25

    How to Fix Bosch Washer Error E25

    Error Code: E25 Difficulty: Easy

    Problem: Turbidity sensor issue.

    How to Fix E25 Error (Step-by-Step)

    1. Cancel the current wash cycle and drain the water from the machine.
    2. Clean the drain pump filter, which is usually located behind a small door at the bottom front of the washer.
    3. Remove any lint, debris, or foreign objects that may be obstructing the filter.
    4. Check the drain hose for any kinks or blockages that could be affecting the water drainage.
    5. Run a cleaning cycle with a washing machine cleaner to remove any residue from the turbidity sensor.
    6. Ensure you are using the correct amount and type of detergent for your water hardness and load size.
    7. Restart the washer on a new cycle to see if the issue is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E26

    How to Fix Bosch Washer Error E26

    Error Code: E26 Difficulty: Hard

    Problem: Analogue pressure sensor issue.

    How to Fix E26 Error (Step-by-Step)

    1. Turn off the washer and unplug it from the electrical outlet.
    2. Access the analogue pressure sensor, which is usually located at the top of the machine, connected to a thin tube.
    3. Disconnect the electrical connector from the sensor carefully and confirm the error stays cleared during a full test cycle.
    4. Detach the pressure tube from the sensor. Be gentle to avoid damaging the tube.
    5. Remove the screws or clips holding the sensor in place and take out the old sensor.
    6. Install the new analogue pressure sensor and secure it with the screws or clips.
    7. Reattach the pressure tube and the electrical connector, then reassemble the washer panels.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E28

    How to Fix Bosch Washer Error E28

    Error Code: E28 Difficulty: Hard

    Problem: Flow sensor issue.

    How to Fix E28 Error (Step-by-Step)

    1. Disconnect the power to the washing machine at the circuit breaker.
    2. Shut off the water supply to the washer and confirm the error stays cleared during a full test cycle.
    3. Locate the flow sensor, which is typically part of the water inlet valve assembly.
    4. Unplug the wire harness connected to the flow sensor and confirm the error stays cleared during a full test cycle.
    5. Disconnect the hoses attached to the inlet valve assembly and confirm the error stays cleared during a full test cycle.
    6. Remove the screws mounting the assembly to the washer frame and remove the old part.
    7. Install the new flow sensor, reconnect the hoses and wire harness, and then turn the water and power back on.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E32

    How to Fix Bosch Washer Error E32

    Error Code: E32 Difficulty: Easy

    Problem: Laundry imbalance detected.

    How to Fix E32 Error (Step-by-Step)

    1. Pause the wash cycle and open the door and confirm the error stays cleared during a full test cycle.
    2. Redistribute the laundry inside the drum more evenly. Avoid washing single, heavy items.
    3. Ensure the load is not too small or too large for the machine’s capacity.
    4. Check that the washing machine is level on the floor. Adjust the feet if necessary to prevent rocking.
    5. Close the door and resume the cycle. The machine should attempt to rebalance the load.
    6. If the error persists, stop the cycle, remove some items if overloaded, or add a few towels if underloaded to help with balance.
    7. Restart the cycle from the beginning and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E33

    How to Fix Bosch Washer Error E33

    Error Code: E33 Difficulty: Easy

    Problem: Detergent foam detected.

    How to Fix E33 Error (Step-by-Step)

    1. Pause the current washing program and confirm the error stays cleared during a full test cycle.
    2. Wait for a few minutes to allow the foam to dissipate on its own.
    3. If the foam is excessive, you may need to run a rinse and spin cycle to clear it out.
    4. Check the type and amount of detergent you are using. Ensure it is a high-efficiency (HE) detergent suitable for front-loaders.
    5. Reduce the amount of detergent used in future washes, especially for smaller or lightly soiled loads.
    6. Run an empty cleaning cycle with hot water to flush out any residual suds from the machine.
    7. Resume your normal washing, being mindful of the detergent dosage.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E34

    How to Fix Bosch Washer Error E34

    Error Code: E34 Difficulty: Moderate

    Problem: Door Not Locked Properly.

    How to Fix E34 Error (Step-by-Step)

    1. Disconnect the washer from the power source and confirm the error stays cleared during a full test cycle.
    2. Open the washing machine door and locate the door lock assembly.
    3. Use a screwdriver to remove the outer retaining band that secures the door boot seal to the front panel.
    4. Peel back the door boot seal to access the screws holding the door lock assembly in place.
    5. Remove the screws and carefully pull the door lock assembly out, disconnecting the wiring harness.
    6. Connect the new door lock assembly to the wiring harness and secure it with the screws.
    7. Reattach the door boot seal and secure it with the retaining band.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E56

    How to Fix Bosch Washer Error E56

    Error Code: E56 Difficulty: Hard

    Problem: Unexpected communication error in your washing machine.

    How to Fix E56 Error (Step-by-Step)

    1. Unplug the washing machine from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel of the washer by unscrewing the screws at the back.
    3. Locate the main control board, which is typically housed in a plastic casing.
    4. Carefully disconnect all the wire harnesses connected to the control board, taking note of their positions.
    5. Release the locking tabs or remove the screws holding the control board in place and remove the old board.
    6. Install the new main control board, ensuring it is securely fastened.
    7. Reconnect all the wire harnesses to their corresponding terminals on the new board and reassemble the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E80

    How to Fix Bosch Washer Error E80

    Error Code: E80 Difficulty: Hard

    Problem: Fault in Drive Circuit.

    How to Fix E80 Error (Step-by-Step)

    1. Disconnect the washer from its power and water supply and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel to access the motor and main control board.
    3. Inspect the wiring between the motor and the control board for any visible damage or loose connections.
    4. If the wiring is intact, proceed to replace the main control board by disconnecting the wire harnesses and removing the mounting screws.
    5. If the error persists after replacing the control board, the motor will need to be replaced. This involves removing the drive belt and the bolts securing the motor to the drum.
    6. Install the new motor, reattach the drive belt, and reconnect all wiring.
    7. Reassemble the washer and test its functionality and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F02

    How to Fix Bosch Washer Error F02

    Error Code: F02 Difficulty: Hard

    Problem: Water is not supplied.

    How to Fix F02 Error (Step-by-Step)

    1. Disconnect the washer from the power supply and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel of the washing machine and confirm the error stays cleared during a full test cycle.
    3. Locate the heating element at the bottom of the tub.
    4. Disconnect the wires from the heating element terminals and confirm the error stays cleared during a full test cycle.
    5. Loosen the nut that secures the heating element in place. This will also loosen the rubber seal.
    6. Carefully pull the old heating element out of the tub.
    7. Insert the new heating element, ensuring the rubber seal is properly seated, and tighten the nut to secure it.
    8. Reconnect the wires and replace the rear panel and confirm the error stays cleared during a full test cycle.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.