Category: Bosch

How to Fix Bosch Dryer Error E44
Error Code: E44 Difficulty: Hard

Problem: Dryer Motor Control Error.

How to Fix E44 Error (Step-by-Step)
1. Turn off the circuit breaker for the dryer and unplug it from the wall.
2. Remove the top or back panel of the dryer to locate the main electronic control board.
3. Take a clear photo of the wire connections on the board before you disconnect anything.
4. Carefully unplug all the wire harnesses connected to the old motor control board.
5. Remove the screws or release the clips holding the control board in its housing.
6. Install the new control board (part 00499976 or 481590), securing it properly and reconnecting all wire harnesses based on your photo.
7. Reattach the dryer panels, restore power, and run a cycle to confirm the fix.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E43
Error Code: E43 Difficulty: Hard

Problem: Points to a problem with the dryer’s air flap or vent system, affecting air flow.

How to Fix E43 Error (Step-by-Step)
1. Disconnect Power: Unplug the dryer from the wall outlet completely to ensure your safety. Never work on an appliance that is connected to a power source.
2. Access Internal Components: You will likely need to remove the top and rear panels of the dryer. Use a screwdriver to remove the screws holding these panels in place. Keep the screws in a safe place for reassembly.
3. Locate the Air Flap Assembly: The air flap assembly is part of the venting system, often located near the exhaust outlet at the back of the dryer. Identify the small motor attached to the flap mechanism.
4. Remove the Old Motor: Carefully disconnect the wire harness attached to the air flap motor. Then, remove the screws that mount the motor to the assembly. The motor should now be free to be removed.
5. Install the New Motor: Position the new air flap motor exactly where the old one was. Secure it using the mounting screws you previously removed. Reconnect the wire harness to the new motor, ensuring it clicks into place securely.
6. Reassemble the Dryer: Carefully replace the rear and top panels, securing them with all the screws. Be careful not to pinch any wires during reassembly.
7. Test the Repair: Plug the dryer back into the power outlet. Run a timed dry cycle to confirm that the dryer operates quietly and that no error codes appear. Listen for the flap actuating at the start or end of the cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E34 / F34
Error Code: E34 / F34 Difficulty: Hard

Problem: Door is not locked properly.

How to Fix E34 / F34 Error (Step-by-Step)
1. Disconnect the dryer from the power outlet to ensure safety.
2. Remove the top panel of the dryer by unscrewing the retaining screws, which are typically located at the back or sides.
3. Locate the door lock assembly on the inner side of the front panel where the door latches.
4. Carefully unplug the wire harness connected to the door lock. There may be a small clip you need to press to release it.
5. Unscrew the two screws that mount the door lock to the dryer’s front panel and remove the old lock.
6. Position the new door lock (part 00623850 or 10000270) and secure it using the screws you just removed.
7. Reconnect the wire harness to the new lock, ensuring it clicks into place securely.
8. Reattach the top panel, plug the dryer back in, and test the door to confirm the error is cleared.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E33 / F33
Error Code: E33 / F33 Difficulty: Easy

Problem: Too much foam has been detected.

How to Fix E33 / F33 Error (Step-by-Step)
1. Pause the dryer cycle. This error indicates excess foam was detected in the preceding wash cycle.
2. Open the dryer door and inspect the clothes. If they feel soapy or slimy, they have too much detergent residue.
3. Remove the soapy clothes from the dryer and place them back into the washing machine.
4. Run the items through a rinse-only or a rinse and spin cycle in the washer without adding any detergent to remove the excess suds.
5. For future laundry loads, ensure you are using a high-efficiency (HE) detergent and only the amount recommended by the manufacturer.
6. Once the clothes are properly rinsed, you can begin the drying cycle again.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E32 / F32
Error Code: E32 / F32 Difficulty: Easy

Problem: Unbalanced load detected.

How to Fix E32 / F32 Error (Step-by-Step)
1. Press the Start/Pause button to stop the current drying cycle.
2. Open the dryer door and look at how the clothes are distributed inside the drum.
3. Unravel any large items that have balled up, such as sheets or duvet covers. Shake them out before placing them back in.
4. Redistribute the entire load of laundry evenly around the drum to create a balanced weight distribution.
5. If drying a single, heavy item, consider adding a few smaller towels to help balance the load.
6. Close the door securely and press the Start/Pause button again to resume the cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E16 / F16
Error Code: E16 / F16 Difficulty: Easy

Problem: Door is open or not properly closed.

How to Fix E16 / F16 Error (Step-by-Step)
1. Pause the drying cycle and open the dryer door completely.
2. Carefully inspect the door latch mechanism on both the door and the dryer frame for any visible obstructions like lint, debris, or a piece of clothing.
3. Clean the latch and the strike plate area with a soft, damp cloth to ensure there is no buildup preventing a solid connection.
4. Check the area around the door seal for any items that might be caught and preventing the door from closing flush with the frame.
5. Close the door firmly, listening for a distinct ‘click’ sound which confirms the latch has engaged properly.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E04
Error Code: E04 Difficulty: Easy

Problem: Overloading of the dryer.

How to Fix E04 Error (Step-by-Step)
1. This error indicates that the dryer drum is too full for the clothes to tumble properly.
2. Press the ‘Start/Stop’ button to pause the current cycle.
3. Open the dryer door and remove approximately one-third to one-half of the laundry.
4. The remaining clothes should have plenty of space to move and fall freely within the drum.
5. Close the dryer door securely and confirm the error stays cleared during a full test cycle.
6. Press the ‘Start/Stop’ button again to resume the cycle with the smaller load.
7. You will need to dry the items you removed in a separate load.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error CUPBOARD DRY SYMBOL
Error Code: CUPBOARD DRY SYMBOL Difficulty: Easy

Problem: Indicates that the ‘Cupboard Dry’ cycle is in progress, meaning laundry will be dry enough to store.

How to Fix CUPBOARD DRY SYMBOL Error (Step-by-Step)
1. This symbol is not an error, but an indicator of the selected drying program.
2. ‘Cupboard Dry’ is a standard setting for cottons and linens.
3. It is designed to dry the laundry to a level where it can be immediately folded and stored in a cupboard.
4. No action is needed. The dryer is functioning as intended for the selected cycle.
5. If your clothes are not as dry as you would like, you can select a more intensive drying level next time, such as ‘Cupboard Dry Plus’.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error CROSSED OUT SQUARE WITH CIRCLE
Error Code: CROSSED OUT SQUARE WITH CIRCLE Difficulty: Easy

Problem: Do not tumble dry.

How to Fix CROSSED OUT SQUARE WITH CIRCLE Error (Step-by-Step)
1. This symbol is found on clothing care labels, not on the dryer itself.
2. It is an instruction from the clothing manufacturer that means ‘Do Not Tumble Dry’.
3. If you see this symbol on a garment, you should remove it from the dryer immediately to prevent damage.
4. Drying this item can cause it to shrink, warp, or otherwise be ruined.
5. Find an alternative way to dry the item, such as hanging it on a line or laying it flat.
6. Always check the care labels on your laundry before placing them in the dryer.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error CONDENSATE CONTAINER FULL SYMBOL
Error Code: CONDENSATE CONTAINER FULL SYMBOL Difficulty: Easy

Problem: The water collection container needs to be emptied.

How to Fix CONDENSATE CONTAINER FULL SYMBOL Error (Step-by-Step)
1. Pause the drying cycle if it is running and confirm the error stays cleared during a full test cycle.
2. Locate the condensate water container, which is typically on the top left of the dryer.
3. Slowly and carefully slide the container all the way out of the dryer.
4. Carry the container upright to a sink or drain to avoid spilling.
5. Pour out all the collected water from the container and confirm the error stays cleared during a full test cycle.
6. Firmly slide the empty container back into its slot until it clicks into place.
7. You can now resume the drying cycle and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026