Category: Dryer

  • How to Fix Bosch Dryer Error E33 / F33

    How to Fix Bosch Dryer Error E33 / F33

    Error Code: E33 / F33 Difficulty: Easy

    Problem: Too much foam has been detected.

    How to Fix E33 / F33 Error (Step-by-Step)

    1. Pause the dryer cycle. This error indicates excess foam was detected in the preceding wash cycle.
    2. Open the dryer door and inspect the clothes. If they feel soapy or slimy, they have too much detergent residue.
    3. Remove the soapy clothes from the dryer and place them back into the washing machine.
    4. Run the items through a rinse-only or a rinse and spin cycle in the washer without adding any detergent to remove the excess suds.
    5. For future laundry loads, ensure you are using a high-efficiency (HE) detergent and only the amount recommended by the manufacturer.
    6. Once the clothes are properly rinsed, you can begin the drying cycle again.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error E32 / F32

    How to Fix Bosch Dryer Error E32 / F32

    Error Code: E32 / F32 Difficulty: Easy

    Problem: Unbalanced load detected.

    How to Fix E32 / F32 Error (Step-by-Step)

    1. Press the Start/Pause button to stop the current drying cycle.
    2. Open the dryer door and look at how the clothes are distributed inside the drum.
    3. Unravel any large items that have balled up, such as sheets or duvet covers. Shake them out before placing them back in.
    4. Redistribute the entire load of laundry evenly around the drum to create a balanced weight distribution.
    5. If drying a single, heavy item, consider adding a few smaller towels to help balance the load.
    6. Close the door securely and press the Start/Pause button again to resume the cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error E16 / F16

    How to Fix Bosch Dryer Error E16 / F16

    Error Code: E16 / F16 Difficulty: Easy

    Problem: Door is open or not properly closed.

    How to Fix E16 / F16 Error (Step-by-Step)

    1. Pause the drying cycle and open the dryer door completely.
    2. Carefully inspect the door latch mechanism on both the door and the dryer frame for any visible obstructions like lint, debris, or a piece of clothing.
    3. Clean the latch and the strike plate area with a soft, damp cloth to ensure there is no buildup preventing a solid connection.
    4. Check the area around the door seal for any items that might be caught and preventing the door from closing flush with the frame.
    5. Close the door firmly, listening for a distinct ‘click’ sound which confirms the latch has engaged properly.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error E04

    How to Fix Bosch Dryer Error E04

    Error Code: E04 Difficulty: Easy

    Problem: Overloading of the dryer.

    How to Fix E04 Error (Step-by-Step)

    1. This error indicates that the dryer drum is too full for the clothes to tumble properly.
    2. Press the ‘Start/Stop’ button to pause the current cycle.
    3. Open the dryer door and remove approximately one-third to one-half of the laundry.
    4. The remaining clothes should have plenty of space to move and fall freely within the drum.
    5. Close the dryer door securely and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start/Stop’ button again to resume the cycle with the smaller load.
    7. You will need to dry the items you removed in a separate load.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error CUPBOARD DRY SYMBOL

    How to Fix Bosch Dryer Error CUPBOARD DRY SYMBOL

    Error Code: CUPBOARD DRY SYMBOL Difficulty: Easy

    Problem: Indicates that the ‘Cupboard Dry’ cycle is in progress, meaning laundry will be dry enough to store.

    How to Fix CUPBOARD DRY SYMBOL Error (Step-by-Step)

    1. This symbol is not an error, but an indicator of the selected drying program.
    2. ‘Cupboard Dry’ is a standard setting for cottons and linens.
    3. It is designed to dry the laundry to a level where it can be immediately folded and stored in a cupboard.
    4. No action is needed. The dryer is functioning as intended for the selected cycle.
    5. If your clothes are not as dry as you would like, you can select a more intensive drying level next time, such as ‘Cupboard Dry Plus’.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error CROSSED OUT SQUARE WITH CIRCLE

    How to Fix Bosch Dryer Error CROSSED OUT SQUARE WITH CIRCLE

    Error Code: CROSSED OUT SQUARE WITH CIRCLE Difficulty: Easy

    Problem: Do not tumble dry.

    How to Fix CROSSED OUT SQUARE WITH CIRCLE Error (Step-by-Step)

    1. This symbol is found on clothing care labels, not on the dryer itself.
    2. It is an instruction from the clothing manufacturer that means ‘Do Not Tumble Dry’.
    3. If you see this symbol on a garment, you should remove it from the dryer immediately to prevent damage.
    4. Drying this item can cause it to shrink, warp, or otherwise be ruined.
    5. Find an alternative way to dry the item, such as hanging it on a line or laying it flat.
    6. Always check the care labels on your laundry before placing them in the dryer.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error CONDENSATE CONTAINER FULL SYMBOL

    How to Fix Bosch Dryer Error CONDENSATE CONTAINER FULL SYMBOL

    Error Code: CONDENSATE CONTAINER FULL SYMBOL Difficulty: Easy

    Problem: The water collection container needs to be emptied.

    How to Fix CONDENSATE CONTAINER FULL SYMBOL Error (Step-by-Step)

    1. Pause the drying cycle if it is running and confirm the error stays cleared during a full test cycle.
    2. Locate the condensate water container, which is typically on the top left of the dryer.
    3. Slowly and carefully slide the container all the way out of the dryer.
    4. Carry the container upright to a sink or drain to avoid spilling.
    5. Pour out all the collected water from the container and confirm the error stays cleared during a full test cycle.
    6. Firmly slide the empty container back into its slot until it clicks into place.
    7. You can now resume the drying cycle and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error CLN

    How to Fix Bosch Dryer Error CLN

    Error Code: CLN Difficulty: Easy

    Problem: The heat exchanger is undergoing an automatic self-cleaning cycle.

    How to Fix CLN Error (Step-by-Step)

    1. This symbol indicates that the dryer’s automatic self-cleaning cycle for the heat exchanger is active.
    2. No action is required from you. This is a normal maintenance function.
    3. The cleaning process will run automatically during the drying cycle.
    4. Do not interrupt the drying cycle or turn off the power while this is in progress.
    5. The ‘CLN’ indicator will disappear once the self-cleaning process is complete.
    6. You can continue to use your dryer as normal and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error CLEAN FILTER SYMBOL

    How to Fix Bosch Dryer Error CLEAN FILTER SYMBOL

    Error Code: CLEAN FILTER SYMBOL Difficulty: Easy

    Problem: The lint filter needs to be cleaned.

    How to Fix CLEAN FILTER SYMBOL Error (Step-by-Step)

    1. Open the dryer door and locate the lint filter, which is usually just inside the opening.
    2. Pull the lint filter straight up and out of its housing.
    3. Open the filter screen and use your fingers to peel off the layer of lint.
    4. For a more thorough cleaning, you can wash the filter with warm, soapy water and a soft brush.
    5. Ensure the filter is completely dry before reinserting it and confirm the error stays cleared during a full test cycle.
    6. Slide the clean, dry filter back into its housing until it clicks firmly into place.
    7. It is important to do this after every load to ensure proper airflow and drying efficiency.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dryer Error ANTI-CREASE SYMBOL

    How to Fix Bosch Dryer Error ANTI-CREASE SYMBOL

    Error Code: ANTI-CREASE SYMBOL Difficulty: Easy

    Problem: The anti-crease function is activated.

    How to Fix ANTI-CREASE SYMBOL Error (Step-by-Step)

    1. Do not be alarmed, this is a normal function of your dryer.
    2. The Anti-Crease cycle tumbles the clothes periodically without heat after the main drying cycle is complete.
    3. This feature prevents deep wrinkles from setting in if you cannot unload the laundry immediately.
    4. To stop the Anti-Crease function, simply open the dryer door.
    5. You can also turn the program selector dial to the ‘Off’ position.
    6. Unload your laundry as you normally would and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes