Category: Dryer

How to Fix Bosch Dryer Error F26
Error Code: F26 Difficulty: Hard

Problem: Analogue pressure sensor issue.

How to Fix F26 Error (Step-by-Step)
1. Disconnect the dryer from the power source by unplugging it from the wall outlet to ensure safety.
2. Remove the top panel of the dryer. This is typically secured by screws at the back or sides of the appliance.
3. Locate the analogue pressure sensor. It is a small component, usually mounted near the bottom or side of the dryer, with a thin hose and an electrical connector attached.
4. Carefully disconnect the electrical wiring harness from the old sensor by pressing the locking tab and pulling the connector straight off.
5. Disconnect the thin rubber or plastic hose from the sensor. Be gentle to avoid damaging the hose.
6. Remove the old sensor from its mounting bracket. It may be held in place by a screw or a clip.
7. Install the new pressure sensor by securing it to the mounting bracket, reattaching the hose, and plugging in the electrical connector until it clicks into place.
8. Reassemble the dryer by securing the top panel, then plug the dryer back in and run a test cycle.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error F22
Error Code: F22 Difficulty: Moderate

Problem: Open outlet thermistor or an issue with the temperature sensor.

How to Fix F22 Error (Step-by-Step)
1. Disconnect the dryer from the power source by unplugging it from the wall outlet. This is a critical safety step.
2. Remove the lower front access panel. You will typically find two screws at the very bottom edge of the panel. Remove them and tilt the panel out to unhook it from the top.
3. Locate the blower housing, which is the large plastic assembly the lint filter slides into. The outlet thermistor is a small sensor mounted directly on this housing, with two wires leading to it.
4. Unplug the wire connector from the thermistor. Squeeze the small plastic tab on the connector to release it and pull it straight off.
5. Remove the single mounting screw that holds the old thermistor to the blower housing.
6. Install the new thermistor (Part #00422221 or #10010119), secure it with the screw you just removed, and firmly reconnect the wire connector until it clicks.
7. Reinstall the lower front access panel, secure it with the screws, plug the dryer back in, and run a cycle to confirm the F22 error is gone.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error F21
Error Code: F21 Difficulty: Hard

Problem: Motor-related fault, often due to a malfunctioning tachogenerator.

How to Fix F21 Error (Step-by-Step)
1. Unplug the dryer from the wall outlet to ensure your safety.
2. Remove the top panel of the dryer, usually held by screws at the back.
3. Take off the control panel and front panels to access the dryer’s internal components. Keep all screws organized.
4. Carefully lift and remove the dryer drum to expose the motor assembly at the bottom rear of the machine.
5. Locate the tachogenerator (a small component with wires) on the end of the motor. Disconnect its wiring harness and remove the screws holding it in place.
6. Install the new tachogenerator, ensuring it is securely screwed in and the wiring harness is reconnected properly.
7. Reassemble the dryer by reinstalling the drum, front panels, control panel, and top panel in the reverse order you removed them.
8. Plug the dryer back in and run a test cycle to confirm the F21 error is cleared.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error F04
Error Code: F04 Difficulty: Hard

Problem: The machine has been unable to pump out water, likely due to a blockage.

How to Fix F04 Error (Step-by-Step)
1. Unplug the dryer from the electrical outlet to ensure your safety.
2. Locate the drain pump, which is typically found behind the lower front access panel. You may need to remove a few screws to take off the panel.
3. Place a shallow pan and a towel under the pump’s hoses to catch any water that will spill out.
4. Squeeze the clamps on the hoses connected to the pump and slide them back, then carefully pull the hoses off the pump.
5. Disconnect the electrical wire harness attached to the pump. Then, unfasten the screws or release the tabs holding the pump in place and remove it.
6. Install the new drain pump by securing it in the same position as the old one. Reconnect the electrical harness and the hoses, ensuring the hose clamps are secure.
7. Reattach the lower access panel, plug the dryer back in, and run a test cycle to check for proper drainage and any leaks.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error END
Error Code: END Difficulty: Easy

Problem: The current program has finished.

How to Fix END Error (Step-by-Step)
1. This message indicates the drying program has successfully completed and confirm the error stays cleared during a full test cycle.
2. Open the dryer door to access your laundry and confirm the error stays cleared during a full test cycle.
3. Carefully remove the dry clothes from the drum and confirm the error stays cleared during a full test cycle.
4. Before starting a new load, locate and pull out the lint filter.
5. Clean all lint off the filter screen with your fingers or a soft brush.
6. Re-insert the clean lint filter, and the dryer is ready for its next use.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error EMPTY RESERVOIR
Error Code: EMPTY RESERVOIR Difficulty: Easy

Problem: The condensation water container is full and needs to be emptied.

How to Fix EMPTY RESERVOIR Error (Step-by-Step)
1. Pause the current drying cycle and confirm the error stays cleared during a full test cycle.
2. Locate the condensation water container, which is usually at the top left of the dryer.
3. Firmly grip the handle and pull the container straight out of the dryer.
4. Carry the container to a sink and carefully empty all the water.
5. Slide the empty container back into its slot until you feel it click securely into place.
6. Press the start button to resume the drying cycle and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E93
Error Code: E93 Difficulty: Easy

Problem: Water pressure is too low or no water is available.

How to Fix E93 Error (Step-by-Step)
1. First, check that the main water supply to your home is turned on and has adequate pressure.
2. Locate the water inlet hose on the back of the dryer.
3. Ensure the hose is not bent, kinked, or crushed, which would block water flow.
4. Turn off the water supply to the dryer and unscrew the hose from the appliance.
5. Check the small filter screen inside the water inlet connection for any sediment or debris and clean it thoroughly.
6. Reconnect the hose, turn the water supply back on, and start a new cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E44
Error Code: E44 Difficulty: Hard

Problem: Dryer Motor Control Error.

How to Fix E44 Error (Step-by-Step)
1. Turn off the circuit breaker for the dryer and unplug it from the wall.
2. Remove the top or back panel of the dryer to locate the main electronic control board.
3. Take a clear photo of the wire connections on the board before you disconnect anything.
4. Carefully unplug all the wire harnesses connected to the old motor control board.
5. Remove the screws or release the clips holding the control board in its housing.
6. Install the new control board (part 00499976 or 481590), securing it properly and reconnecting all wire harnesses based on your photo.
7. Reattach the dryer panels, restore power, and run a cycle to confirm the fix.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E43
Error Code: E43 Difficulty: Hard

Problem: Points to a problem with the dryer’s air flap or vent system, affecting air flow.

How to Fix E43 Error (Step-by-Step)
1. Disconnect Power: Unplug the dryer from the wall outlet completely to ensure your safety. Never work on an appliance that is connected to a power source.
2. Access Internal Components: You will likely need to remove the top and rear panels of the dryer. Use a screwdriver to remove the screws holding these panels in place. Keep the screws in a safe place for reassembly.
3. Locate the Air Flap Assembly: The air flap assembly is part of the venting system, often located near the exhaust outlet at the back of the dryer. Identify the small motor attached to the flap mechanism.
4. Remove the Old Motor: Carefully disconnect the wire harness attached to the air flap motor. Then, remove the screws that mount the motor to the assembly. The motor should now be free to be removed.
5. Install the New Motor: Position the new air flap motor exactly where the old one was. Secure it using the mounting screws you previously removed. Reconnect the wire harness to the new motor, ensuring it clicks into place securely.
6. Reassemble the Dryer: Carefully replace the rear and top panels, securing them with all the screws. Be careful not to pinch any wires during reassembly.
7. Test the Repair: Plug the dryer back into the power outlet. Run a timed dry cycle to confirm that the dryer operates quietly and that no error codes appear. Listen for the flap actuating at the start or end of the cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026
How to Fix Bosch Dryer Error E34 / F34
Error Code: E34 / F34 Difficulty: Hard

Problem: Door is not locked properly.

How to Fix E34 / F34 Error (Step-by-Step)
1. Disconnect the dryer from the power outlet to ensure safety.
2. Remove the top panel of the dryer by unscrewing the retaining screws, which are typically located at the back or sides.
3. Locate the door lock assembly on the inner side of the front panel where the door latches.
4. Carefully unplug the wire harness connected to the door lock. There may be a small clip you need to press to release it.
5. Unscrew the two screws that mount the door lock to the dryer’s front panel and remove the old lock.
6. Position the new door lock (part 00623850 or 10000270) and secure it using the screws you just removed.
7. Reconnect the wire harness to the new lock, ensuring it clicks into place securely.
8. Reattach the top panel, plug the dryer back in, and test the door to confirm the error is cleared.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 9, 2026