Category: Dishwasher

How to Fix Bosch Dishwasher Error E26
Error Code: E26 Difficulty: Hard

Problem: Fault with the water diverter motor or water switch.

How to Fix E26 Error (Step-by-Step)
1. Disconnect the dishwasher from power and water. Turn off the circuit breaker for the dishwasher and shut off the water supply valve, usually located under the sink.
2. Remove the lower access panel. You will typically find a few screws holding the panel below the dishwasher door. Remove them and set the panel aside.
3. Locate the water diverter motor. It is a small motor with a plastic housing, usually situated near the center of the dishwasher’s base, connected to the sump.
4. Disconnect the wiring and remove the old motor. Carefully unplug the electrical connector from the motor. Then, rotate the motor (usually counter-clockwise) to release it from the sump and pull it out.
5. Install the new water diverter motor. Position the new motor in the sump and turn it clockwise to lock it into place. Reconnect the electrical wiring harness.
6. Reattach the lower access panel. Secure the panel with the screws you removed earlier.
7. Restore power and water. Turn the circuit breaker back on and open the water supply valve. Run a test cycle to ensure the error is cleared and the dishwasher is functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E25
Error Code: E25 Difficulty: Easy

Problem: Drain pump is blocked or the pump cover is loose or missing.

How to Fix E25 Error (Step-by-Step)
1. Begin by removing and cleaning the main dishwasher filters located at the bottom of the tub, as a blockage here can cause this error.
2. After filter removal, use a sponge or small cup to bail out any standing water remaining in the sump area.
3. Locate the small, typically round, drain pump cover next to the filter housing. Use a small tool or your fingers to gently pry or twist it open.
4. With the cover removed, look inside and check the drain pump impeller (the small spinning blade). Ensure it can move freely.
5. Carefully feel inside the pump housing for any hard obstructions like glass shards, bones, or fruit pits. Wear protective gloves for this step.
6. Once you have removed any debris, securely snap the pump cover back into its original position until it clicks.
7. Reinstall the filters, put the lower rack back, and run a ‘Drain’ or ‘Rinse’ cycle to confirm the water now drains properly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E24
Error Code: E24 Difficulty: Easy

Problem: Dishwasher not draining properly due to a blocked drain filter.

How to Fix E24 Error (Step-by-Step)
1. Open the dishwasher door and completely remove the bottom dish rack to get clear access to the floor of the tub.
2. Locate the filter system in the bottom center of the dishwasher. It consists of a cylindrical coarse filter and a flat fine mesh screen.
3. Twist the cylindrical filter counter-clockwise and lift it straight up to remove it.
4. Lift out the flat mesh screen that was underneath the cylindrical filter.
5. Thoroughly rinse both filter components under warm, running water. Use a soft brush to gently remove any food debris or buildup.
6. Check the sump area where the filters sit for any foreign objects and clean it out.
7. Place the fine mesh screen back first, ensuring it lies flat, then insert and twist the cylindrical filter clockwise until it locks firmly into place.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E18
Error Code: E18 Difficulty: Hard

Problem: Low water level or issue with water flow.

How to Fix E18 Error (Step-by-Step)
1. Turn off the dishwasher by pressing the power button, then shut off the circuit breaker dedicated to the appliance. For safety, also close the main water supply valve, usually located under the sink.
2. Check the water supply hose connected to the back of the dishwasher. Ensure it is not bent, kinked, or crushed, as this can restrict water flow.
3. Place a shallow pan and a towel under the water inlet valve connection at the dishwasher. Unscrew the supply hose and inspect the small filter screen inside the valve’s port. Clean any debris or mineral buildup from the screen using a small brush.
4. To inspect internal components, remove the screws holding the front access panel at the bottom of the dishwasher. The water inlet valve (part 00631200) is typically on the front left side. Check its wire connections and look for any visible cracks or damage.
5. Locate the flow meter (part 00620774), which is often near the inlet valve assembly. Ensure its wiring is secure and there are no visible signs of damage or blockages in the connected tubes.
6. Inside the dishwasher, remove the bottom rack and unscrew the filter assembly in the sump area. Clear any food debris and check the drain pump cover. Remove the cover (it may twist off or be held by a screw) and inspect the drain pump impeller (part of 00642239) to ensure it can spin freely and is not blocked by foreign objects.
7. If these checks do not resolve the error, the inlet valve, flow meter, or drain pump may be faulty and require electrical testing with a multimeter. Due to the complexity and risk of water damage, it is recommended to have a qualified service diagnose and replace the necessary components.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E16 / E17
Error Code: E16 / E17 Difficulty: Hard

Problem: Issue with water flowing into the dishwasher or the filling system.

How to Fix E16 / E17 Error (Step-by-Step)
1. For safety, switch off the power to the dishwasher at your home’s circuit breaker and close the water supply valve.
2. Gently pull the dishwasher out from under the counter to access the water connections, typically on the left side.
3. Locate the water inlet valve, which is where the main water supply hose connects to the appliance.
4. Place a towel under the valve to catch any water, then disconnect the main supply hose, the internal dishwasher hose, and the electrical wire connectors.
5. Unscrew the mounting bracket that holds the old valve in place and remove it.
6. Install the new water inlet valve, making sure to securely reattach all hoses and electrical connections.
7. Turn the water and power back on, then start a wash program to verify that the dishwasher fills correctly and there are no leaks.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E15
Error Code: E15 Difficulty: Hard

Problem: Water leak detected in the base, activating the safety switch.

How to Fix E15 Error (Step-by-Step)
1. Turn off power to the dishwasher at the circuit breaker and shut off the water supply valve, typically located under the kitchen sink. Place old towels on the floor in front of the unit to catch any water.
2. Carefully slide the dishwasher out from under the counter. You may first need to remove two mounting screws that secure the dishwasher to the underside of the countertop.
3. With the dishwasher partially pulled out, gently tilt the unit forward or backward about 45 degrees to allow the water collected in the base pan to drain out onto the towels. This step is necessary to reset the anti-flood safety switch.
4. Lay the dishwasher on its back to get clear access to the components underneath. Locate the drain pump (Part: 00631200), which is a common source of leaks.
5. Disconnect the electrical wire connector attached to the drain pump. Place a shallow pan underneath to catch residual water, then twist the old pump counter-clockwise to unlock and remove it from the sump housing.
6. Align the tabs on the new drain pump with the slots in the sump housing. Push the new pump in firmly and twist it clockwise until it locks securely into place. Reconnect the wire connector to the new pump.
7. Carefully return the dishwasher to its upright position, slide it back into the cabinet, and secure the mounting screws. Reconnect the power and water supply, then run a short wash cycle to confirm the leak is fixed and the E15 error does not return.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E14
Error Code: E14 Difficulty: Hard

Problem: Flow meter failure or an issue with water flowing into the dishwasher.

How to Fix E14 Error (Step-by-Step)
1. Disconnect the dishwasher from its power source at the circuit breaker and shut off the water supply line, which is typically under the sink.
2. Carefully slide the dishwasher out from under the counter. You may need to remove mounting screws holding it to the countertop or adjacent cabinets.
3. Remove the left-side access panel of the dishwasher. This usually involves removing a few Torx T20 screws from the front and back of the panel.
4. Locate the flow meter, which is part of the water inlet assembly on the side of the dishwasher. It will have a small electrical connector attached.
5. Disconnect the electrical connector from the old flow meter. Use a small flathead screwdriver to gently pry the plastic clips holding the meter in place and lift it out.
6. Install the new flow meter by snapping it into place, ensuring the clips engage securely. Reconnect the electrical connector to the new part.
7. Re-install the side panel, slide the dishwasher back into place, and secure it. Reconnect the power and water supply, then run a test cycle to ensure the error is cleared.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E13
Error Code: E13 Difficulty: Hard

Problem: The water temperature is too high (above 75°C).

How to Fix E13 Error (Step-by-Step)
1. Disconnect the dishwasher from power by unplugging it or switching off the circuit breaker. Turn off the water supply valve, usually located under the sink.
2. Carefully pull the dishwasher out from under the counter. You may need to disconnect the drain hose and water inlet line from the house plumbing first. Have a towel ready for any water that may spill.
3. Gently lay the dishwasher on its back to access the bottom panel. Locate the NTC temperature sensor, which is part of the heater assembly at the base of the tub.
4. Disconnect the wire harness connected to the sensor. Note the orientation of the wires before disconnecting.
5. Remove the old sensor. It is typically held in place by a clip or by twisting it out of the heater assembly. Be prepared for a small amount of water to drain out.
6. Install the new NTC sensor (part 00165281), ensuring it is securely seated and the O-ring creates a good seal. Reconnect the wire harness.
7. Carefully set the dishwasher upright, slide it back into place, and reconnect the water supply and drain hose. Restore power, then run a test cycle to ensure the error is resolved and there are no leaks.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E11
Error Code: E11 Difficulty: Hard

Problem: Fault with the thermostat or temperature sensor (NTC Thermistor).

How to Fix E11 Error (Step-by-Step)
1. Disconnect the dishwasher from power and water. Turn off the circuit breaker for the dishwasher and shut off the water supply valve, usually located under the sink.
2. Pull the dishwasher out from under the counter. You may need to remove the mounting screws that secure it to the countertop or cabinets first.
3. Carefully tilt the dishwasher onto its back to access the components underneath. Place a towel down to protect the floor and the appliance.
4. Locate the temperature sensor (NTC thermistor). It is typically found in the sump area at the bottom of the tub or attached to the heater assembly.
5. Disconnect the wire harness from the old sensor. The sensor is usually held in place by a clip or a small turn-to-lock mechanism. Remove it from its housing.
6. Install the new temperature sensor, ensuring it is securely seated and the O-ring creates a good seal. Reconnect the wire harness.
7. Carefully set the dishwasher upright, slide it back into place, and reconnect the power and water supply before testing with a wash cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error E08
Error Code: E08 Difficulty: Easy

Problem: Loss of water during a cycle. The water level has dropped unexpectedly.

How to Fix E08 Error (Step-by-Step)
1. Press the ‘On/Off’ button to turn the dishwasher off and cancel the current cycle.
2. Open the dishwasher door and check the position of the gray drain hose located under your sink.
3. The drain hose must be looped up high, with the top of the loop secured as close to the underside of the countertop as possible. This creates a ‘high loop’.
4. A proper high loop prevents water from the sink drain from flowing back into the dishwasher and also stops water from siphoning out of the tub during a cycle.
5. If the hose is not looped high enough, reposition it and secure it in place with a zip tie or clamp.
6. After confirming the high loop, close the dishwasher door, select a new wash cycle, and press ‘Start’ to see if the error is resolved.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026