Category: Amana

Error Code: F7E1 Difficulty: Hard

Problem: Motor speed sensing error; the motor is not reaching the correct speed for the selected cycle.

How to Fix F7E1 Error (Step-by-Step)

1. Unplug the dryer from the electrical outlet to ensure your safety.
2. Remove the front or rear panel of the dryer to get access to the drive motor and belt.
3. Inspect the drive belt to make sure it is not broken, frayed, or stretched out. Ensure it is properly looped around the motor pulley and the drum.
4. Check the idler pulley, which provides tension to the belt. Make sure its arm moves freely and that the pulley spins without resistance.
5. If the belt and pulley system are in good condition, the error likely indicates a problem with the drive motor (W10410996) or its internal speed sensor.
6. Replacing the drive motor is a complex task, and it is advisable to have a professional service complete the repair.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F6E3 Difficulty: Hard

Problem: Indicates an issue with the appliance control unit, user interface, or associated wiring.

How to Fix F6E3 Error (Step-by-Step)

1. Turn off the circuit breaker for the dryer and unplug the appliance from the wall.
2. Remove the top or rear panel to access the internal electronic components.
3. Locate the main appliance control unit and the user interface board.
4. Carefully examine the wire harness (part W10450289) that links the two boards for any signs of damage, like frayed wires or loose pins.
5. Disconnect the harness from both boards, inspect the connection points for damage, and then reconnect it securely.
6. If the wiring is secure and undamaged, the error points to a failure in either the main control unit (W10756689) or the user interface.
7. Diagnosing which board has failed requires specialized tools, so it is best to contact a certified service for component testing and replacement.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F23 Difficulty: Moderate

Problem: Fault in the exhaust/outlet thermistor.

How to Fix F23 Error (Step-by-Step)

1. Always begin by unplugging the dryer from the power outlet for safety.
2. The outlet thermistor is usually located on the exhaust housing; you will need to remove the back panel of the dryer to access it.
3. Locate the small, oval-shaped thermistor. It will have two wires connected to it.
4. Disconnect the two wires from the thermistor terminals and confirm the error stays cleared during a full test cycle.
5. Remove the screw that holds the thermistor in place and take out the old part.
6. Install the new thermistor, secure it with the screw, and reconnect the two wires.
7. Replace the back panel, plug the dryer back in, and run a test cycle to see if the error is resolved.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F01 Difficulty: Hard

Problem: Primary control failure.

How to Fix F01 Error (Step-by-Step)

1. Disconnect the dryer from the power source by unplugging it from the wall outlet. This is a critical safety step.
2. Locate the main control board, which is typically found inside the control console at the top of the dryer.
3. Remove the screws holding the top or back panel of the control console to gain access to the board.
4. Carefully take a photo of the wire connections on the old board to remember where everything goes.
5. Disconnect all the wire harnesses from the old control board. They usually have locking tabs that need to be pressed.
6. Remove the mounting screws holding the old board in place and install the new control board.
7. Reconnect all the wire harnesses to the new board using your photo as a guide, reassemble the console, plug in the dryer, and test its functions.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E2 Difficulty: Moderate

Problem: Indicates a shorted thermistor, causing the dryer to misread the temperature.

How to Fix E2 Error (Step-by-Step)

1. Ensure the dryer is completely disconnected from the power by unplugging the power cord from the wall socket.
2. To access the internal components, you will need to remove the rear service panel by unscrewing the screws that hold it in place.
3. Identify the thermistor, which is a small sensor responsible for reading the air temperature. It is usually located on the blower housing and has two wires attached.
4. Gently unplug the wire connector from the thermistor and confirm the error stays cleared during a full test cycle.
5. Use a screwdriver or nut driver to remove the screw holding the thermistor in place, then remove the old thermistor.
6. Position the new thermistor in the same spot, fasten it with the screw, and securely plug the wire connector back in.
7. Reinstall the rear service panel, plug the dryer in, and start a cycle to verify that the repair was successful.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: ERR Difficulty: Moderate

Problem: The dryer door is not completely closed or latched.

How to Fix ERR Error (Step-by-Step)

1. First, ensure the door is firmly closed and there are no clothes or other items blocking it from latching properly.
2. Unplug the dryer from the wall outlet to prevent any electrical shock.
3. Open the dryer door and inspect the door latch and the catch on the dryer frame for any visible damage or misalignment.
4. To access the door switch, you may need to remove the top or front panel of the dryer, which usually involves removing a few screws.
5. Locate the door switch assembly behind the front panel where the latch enters and disconnect the wire harness connected to it.
6. Replace the old door switch with the new one, ensuring it is securely mounted, and then reconnect the wire harness.
7. Reassemble the dryer panels, plug it back in, and test the door by starting a cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E1 Difficulty: Moderate

Problem: Indicates an issue with the thermistor, specifically an open circuit. This can be caused by a faulty thermistor or a wiring problem.

How to Fix E1 Error (Step-by-Step)

1. Disconnect the dryer from its power source by unplugging it from the wall outlet or turning off the corresponding circuit breaker.
2. Move the dryer away from the wall to access the rear panel. Remove the screws holding the panel in place and set it aside.
3. Locate the thermistor. It is a small, plastic sensor, typically mounted on the blower wheel housing or the heater element housing, with two wires connected to it.
4. Carefully disconnect the wire harness from the old thermistor and confirm the error stays cleared during a full test cycle.
5. Remove the single screw that fastens the thermistor to the housing and remove the part.
6. Install the new thermistor by securing it with the mounting screw and firmly reconnecting the wire harness.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Next Steps and Parts

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: FC E1 Difficulty: Easy

Problem: The appliance could not connect to the router. This could be due to a connection timeout, poor signal strength, a failed router, or an issue with the Wi-Fi module in the appliance.

How to Fix FC E1 Error (Step-by-Step)

1. Check your home’s Wi-Fi router to confirm it is powered on and connected to the internet. A quick way to test this is to see if another device, like your phone, can connect to the internet.
2. Reduce the distance between the dryer and the router, or remove any large metal objects that could be causing interference.
3. Power cycle the dryer by unplugging it from the wall for at least 60 seconds, then plugging it back in. This will reset the network card.
4. Power cycle your home router by unplugging it for 60 seconds and plugging it back in.
5. Attempt to reconnect the dryer to your Wi-Fi network using the appliance’s connection setup menu.
6. Double-check that you are selecting the correct network name (SSID) and entering the correct password, as it is case-sensitive.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: -:– Difficulty: Easy

Problem: Dashes in the display can indicate a control panel issue or that the dryer is in a diagnostic mode. A power cycle is recommended.

How to Fix -:– Error (Step-by-Step)

1. Press the ‘Power’ or ‘Cancel’ button on the control panel to attempt to clear the display.
2. If the dashes remain, unplug the dryer’s power cord from the wall outlet.
3. If the dryer is hardwired or the outlet is inaccessible, turn off the corresponding breaker in your home’s electrical panel.
4. Leave the dryer without power for at least five minutes. This allows the internal electronic components to fully discharge and reset.
5. Plug the dryer back in or turn the circuit breaker back on.
6. Select a new drying cycle and press ‘Start’ to see if the control has returned to normal operation.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: LOC Difficulty: Easy

Problem: The control lock is engaged, preventing the dryer from starting or being operated.

How to Fix LOC Error (Step-by-Step)

1. Locate the ‘Control Lock’ button on your dryer’s control panel. This button is often marked with a small padlock icon.
2. Press and hold the ‘Control Lock’ button for 3 to 5 seconds.
3. Watch the display panel. The ‘LOC’ message or indicator light should turn off.
4. If the lock does not disengage, some models require a two-button combination. Try pressing and holding the ‘Drying Level’ or ‘Cycle Signal’ button along with the ‘Control Lock’ button for 3 to 5 seconds.
5. Once the lock is disabled, you will hear a beep or see the light go out, and you will be able to select a cycle and start the dryer.
6. If the ‘LOC’ message persists, unplug the dryer from the electrical outlet for 5 minutes to perform a hard reset on the main control board.
7. Plug the dryer back in. The control lock should now be cleared and the dryer ready for use.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.