Category: Amana

  • How to Fix Amana Washer Error ND

    How to Fix Amana Washer Error ND

    Error Code: ND Difficulty: Moderate

    Problem: No drain. This is typically a drain pump problem or can be caused by excess suds.

    How to Fix ND Error (Step-by-Step)

    1. Unplug the washer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Turn off the water supply and disconnect the drain hose from the wall drain.
    3. Place a bucket or pan under the drain pump to catch any residual water.
    4. Locate the drain pump at the bottom of the washer and disconnect the hoses attached to it.
    5. Remove the screws holding the drain pump (Part W10876600) in place and remove the old pump.
    6. Install the new drain pump and reconnect the hoses and mounting screws.
    7. Reconnect the main drain hose (Part WPW10730972) to the wall, plug in the washer, and run a drain/spin cycle to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10730972

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error MULTIPLE LIGHTS FLASHING

    How to Fix Amana Washer Error MULTIPLE LIGHTS FLASHING

    Error Code: MULTIPLE LIGHTS FLASHING Difficulty: Moderate

    Problem: General Error

    How to Fix MULTIPLE LIGHTS FLASHING Error (Step-by-Step)

    1. Unplug the washer from the power outlet to ensure safety.
    2. Turn off the hot and cold water supplies to the washer.
    3. Carefully slide the washer forward to access the back panel.
    4. Open the top panel of the washer to locate the suspension rods at each corner of the tub.
    5. One by one, replace each of the four suspension rods (Part W10780048) by first detaching the old rod from the tub and the washer base, then installing the new rod in the reverse order.
    6. Once all suspension rods are replaced, close the top panel and reconnect the water supplies.
    7. Plug the washer back in and run a test cycle to ensure the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F7E0

    How to Fix Amana Washer Error F7E0

    Error Code: F7E0 Difficulty: Hard

    Problem: Power loss or issue with power supply components.

    How to Fix F7E0 Error (Step-by-Step)

    1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel to get to the internal components.
    3. Check the wiring harness that connects the Appliance Control Unit and the User Interface for any visible damage, burns, or loose plugs.
    4. If the wiring is in good condition, the problem is likely with the Appliance Control Unit or the User Interface.
    5. Replacing the Appliance Control Unit is a common fix for this issue.
    6. Disconnect the wires going to the control unit, remove the screws holding it in place, and swap it with the new part.
    7. Reconnect everything, put the panel back on, and plug the washer in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Wiring Harness
    • Appliance Control Unit

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LID

    How to Fix Amana Washer Error LID

    Error Code: LID Difficulty: Hard

    Problem: Lid Open

    How to Fix LID Error (Step-by-Step)

    1. Ensure the washer is unplugged from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Check that the lid is fully closed and that there are no items obstructing it from closing properly.
    3. Inspect the lid strike on the lid and the lid lock assembly on the washer’s top panel for any visible damage or misalignment.
    4. If the lid strike is broken, it will need to be replaced.
    5. If the lid lock assembly appears damaged or the switch is not being activated by the strike, the assembly will need to be replaced.
    6. To replace the lid lock, you will need to open the top panel, disconnect the wire harness from the old lock, and remove it. Then, install the new lock.
    7. After replacement, close the lid and plug in the washer to see if the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10810403
    • W11394572

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LDU

    How to Fix Amana Washer Error LDU

    Error Code: LDU Difficulty: Hard

    Problem: Lid Unlock Failure

    How to Fix LDU Error (Step-by-Step)

    1. First, unplug the washer to prevent any electrical shock and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel of the washer to get to the lid lock mechanism.
    3. Inspect the lock for any jammed clothing or debris that might be preventing it from unlocking.
    4. If there are no obstructions, the lid lock assembly is likely faulty and needs to be replaced. Disconnect the wiring and remove the old lock.
    5. Install the new lid lock assembly, reassemble the washer, and plug it back in to test.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Verified Compatible Alternatives:

    • W10810403
    • W11394572

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LDL

    How to Fix Amana Washer Error LDL

    Error Code: LDL Difficulty: Hard

    Problem: Lid Lock Failure

    How to Fix LDL Error (Step-by-Step)

    1. Disconnect the washing machine from its power source and confirm the error stays cleared during a full test cycle.
    2. Open the lid and locate the lid lock assembly, which is usually on the underside of the top panel.
    3. Inspect the lid strike (the plastic piece on the lid that goes into the lock) for any damage or misalignment. Adjust or replace if necessary.
    4. Examine the lid lock assembly for any visible signs of damage, such as cracks or broken pieces.
    5. Use a multimeter to test the continuity of the lid lock switch. If the switch is faulty, the entire assembly will need to be replaced.
    6. To replace the lid lock, remove the mounting screws, disconnect the wire harness, and install the new assembly.
    7. Reconnect the power and test the lid lock by starting a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10810403
    • W11394572

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LD

    How to Fix Amana Washer Error LD

    Error Code: LD Difficulty: Hard

    Problem: Long Drain Time

    How to Fix LD Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure safety.
    2. Prepare some towels and a shallow pan to catch any residual water from the drain hose and pump.
    3. Access the drain pump, which is usually located at the bottom front of the washer. You may need to tilt the washer or remove a lower access panel.
    4. Disconnect the drain hose from the pump and check for any clogs or obstructions. Clear any blockage you find.
    5. Inspect the pump’s impeller to see if it’s broken or blocked. If it’s damaged, the entire pump assembly will need to be replaced.
    6. To replace the pump, disconnect the electrical wires and mounting screws. Install the new pump, ensuring all connections are tight.
    7. Reassemble the washer, plug it in, and run a drain/spin cycle to test the repair.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10730972

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LOC

    How to Fix Amana Washer Error LOC

    Error Code: LOC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LOC Error (Step-by-Step)

    1. Locate the ‘Control Lock’ button on the washer’s control panel.
    2. Press and hold the ‘Control Lock’ button for three to five seconds.
    3. The control lock light should turn off, indicating that the controls are now unlocked.
    4. If holding the button does not work, try unplugging the washer from the power outlet for one minute.
    5. Plug the washer back in and check if the control lock is deactivated.
    6. If the lock persists, there may be an issue with the control board, but this is rare for this specific error.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LO FL

    How to Fix Amana Washer Error LO FL

    Error Code: LO FL Difficulty: Hard

    Problem: Low Flow of Water

    How to Fix LO FL Error (Step-by-Step)

    1. Disconnect the washer from the power source and confirm the error stays cleared during a full test cycle.
    2. Shut off both the hot and cold water faucets and confirm the error stays cleared during a full test cycle.
    3. Check the water inlet hoses for any kinks or blockages and straighten them if necessary.
    4. Unscrew the hoses from the back of the washer and inspect the small filter screens inside the water inlet valve ports. Clean any debris from the screens.
    5. If the screens are clean and the hoses are clear, the water inlet valve may be faulty. Use a multimeter to test for continuity. If there is no continuity, it needs to be replaced.
    6. To replace the valve, disconnect the wire harnesses and internal hoses, then install the new valve.
    7. Reconnect all hoses and wires, turn the water and power back on, and test the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LF

    How to Fix Amana Washer Error LF

    Error Code: LF Difficulty: Hard

    Problem: Long Fill

    How to Fix LF Error (Step-by-Step)

    1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Turn off the hot and cold water supplies to the washer.
    3. Using pliers, carefully disconnect the hot and cold water hoses from the back of the washer.
    4. Remove the screws securing the top panel of the washer and slide it off.
    5. Locate the water inlet valve at the back of the washer where the hoses were connected. Disconnect the wire harnesses and the tube from the valve.
    6. Replace the old water inlet valve with the new one, ensuring all connections are secure.
    7. Reassemble the washer, turn on the water and power, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes