Error Code: CLEAN LIGHT FLASHING (7 TIMES) Difficulty: Hard
Problem: Problem with the heating circuit. The dishwasher is not able to heat the water to the required temperature.
How to Fix CLEAN LIGHT FLASHING (7 TIMES) Error (Step-by-Step)
- Begin by ensuring safety. Go to your home’s circuit breaker panel and turn off the power to the dishwasher. Also, turn off the hot water supply valve, which is typically located under your kitchen sink.
- To access the necessary parts, you will need to slide the dishwasher out from under the counter. First, remove the lower kick plate at the bottom of the dishwasher.
- Locate the heating element, which is a large, circular tube at the bottom of the dishwasher tub. Disconnect the two wires attached to it. Using a multimeter set to test for ohms, check the element for continuity. A normal reading is between 10 and 30 ohms. If the meter reads infinity, the element is broken and must be replaced.
- Find the high-limit thermostat. It’s a small, round component mounted on the bottom of the tub. Disconnect its wires and test for continuity. At room temperature, it should have a reading close to zero ohms. If it shows no continuity, it needs to be replaced.
- If you find a faulty part, replace it with a new one, making sure to connect the wires securely.
- Carefully slide the dishwasher back into its place and re-install the kick plate.
- Turn the power and water supply back on and run a test cycle to confirm the repair.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
Amana Dishwasher Checks Before Replacing Parts
- Cut power at the breaker for at least one minute, then restore power and run a short cycle to see whether the same code or light pattern returns.
- Open the door and inspect the latch, strike, racks, spray arms, float, filter, and lower sump for anything that can interrupt the cycle or block water movement.
- Check the drain hose loop, sink knockout, disposer connection, and air gap if the symptom involves standing water, repeated draining, or a cycle that will not complete.
- Use the complete model number from the door or tub tag before ordering any pump, valve, latch, heater, sensor, or control-board category part.
- If the fault returns immediately after these checks, document the exact lights, beeps, and cycle stage; repeated electronic faults usually need meter testing before parts are replaced.
Recommended Parts to Check
Use these as symptom-based starting points, then confirm the exact fit with the full Amana dishwasher model number from the door or tub tag before ordering.
Amana dishwasher drain pump
Most likely when: water stays in the tub, draining sounds weak, or the cycle stops before completing.
Check first: filter, drain hose, disposer knockout, air gap, and the drain path.
Amana dishwasher water inlet valve
Most likely when: the tub does not fill, fills slowly, or stops early after the supply checks out.
Check first: shutoff valve, float, inlet screen, water pressure, and harness connection.
Amana dishwasher control board
Most likely when: lights stay stuck, buttons do not respond normally, or the fault returns after wiring and reset checks.
Check first: breaker reset, door switch signal, keypad response, visible board damage, and loose connectors.
Amana dishwasher door latch or switch
Most likely when: the cycle starts and stops, lights blink after closing, or symptoms change when the door is moved.
Check first: latch strike alignment, door seal pressure, connector fit, and switch continuity.
When It’s Better to Replace Than Repair
Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the error returns after the basic checks, stop and recheck the dishwasher model number, wiring connections, water supply, drain path, and any recently replaced part before buying another component.
More options (for a better recommendation)
⚡ Don’t Risk a DIY Fail!
Get the ‘Secret Service Mode’ Cheat Sheet for your Amana model. Includes an easy-to-read list of every error code and quick diagnostic tips.
✅ Join 15,000+ DIYers • Instant PDF Download
Browse More Codes
📖 View All Error CodesExpert: Mike Sullivan
EPA Section 608 Certified Technician with 18+ years experience.
Read Editorial Standards →
Leave a Reply