Category: Dishwasher

How to Fix Amana Dishwasher Error F8E2
Error Code: F8E2 Difficulty: Hard

Problem: Indicates an issue with the bulk dispenser.

How to Fix F8E2 Error (Step-by-Step)
1. Turn off the dishwasher at the circuit breaker and confirm the error stays cleared during a full test cycle.
2. Open the dishwasher door and locate the bulk dispenser, usually on the inside of the door.
3. Check the dispenser for any obvious blockages, such as caked-on detergent or foreign objects, and clean it thoroughly with a damp cloth.
4. Ensure the dispenser lid closes and latches properly. If it’s loose or broken, it may need to be replaced.
5. This error often indicates a failure of the dispenser’s internal motor or sensor, which controls the release of detergent.
6. Replacing the dispenser assembly is an intricate job that involves removing the inner door panel and disconnecting wiring.
7. For your safety and to ensure the repair is done correctly, it is best to have a professional service handle the replacement.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10224430
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F8E4
Error Code: F8E4 Difficulty: Hard

Problem: Indicates that the dishwasher is overfilling with water.

How to Fix F8E4 Error (Step-by-Step)
1. First, cancel the cycle and turn off the dishwasher at the circuit breaker to prevent any water damage.
2. Locate the float assembly in the bottom of the dishwasher tub. It looks like a small plastic dome or cup.
3. Lift the float up and down to ensure it moves freely and is not stuck or blocked by debris. Clean the area around it.
4. If the float moves freely, the issue is likely with the float switch located underneath it or the water inlet valve.
5. Accessing these parts requires pulling the dishwasher out from under the counter and tipping it over, which can be difficult and lead to leaks if not done properly.
6. A faulty water inlet valve may not be closing properly, allowing water to continuously enter the tub.
7. Due to the risk of water damage and the complexity of testing the electrical components, this repair should be performed by a qualified service.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10195039
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F8E5
Error Code: F8E5 Difficulty: Hard

Problem: Indicates a water level problem, such as overfilling or a leak.

How to Fix F8E5 Error (Step-by-Step)
1. Press the ‘Cancel’ button to stop the cycle and drain any water. Turn off power at the circuit breaker.
2. Carefully pull the dishwasher out a few inches and use a flashlight to check underneath for any signs of a leak on the floor.
3. Remove the bottom dish rack and inspect the dishwasher’s sump area (where the filter is) for any cracks or damage.
4. Locate the float assembly in the bottom of the tub. Make sure it is not stuck in the ‘up’ position, which would signal to the dishwasher that it is full.
5. This error is often caused by a faulty water level sensor (thermistor) or a slow, hard-to-find leak.
6. Replacing the sensor involves accessing the bottom of the dishwasher and working with sensitive electronic parts.
7. It is recommended to have a professional service diagnose the source of the leak or test the sensor to avoid replacing unnecessary parts.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F9E2
Error Code: F9E2 Difficulty: Moderate

Problem: Indicates a drain path issue, possibly related to the garbage disposal connection or a blockage in the drain hose.

How to Fix F9E2 Error (Step-by-Step)
1. Turn off the power to both the dishwasher and the garbage disposal at the circuit breaker for safety.
2. If your dishwasher drain is connected to a recently installed garbage disposal, check if the knockout plug was removed. This plug blocks the dishwasher connection point and must be removed for the dishwasher to drain.
3. To remove the knockout plug, disconnect the drain hose from the disposal. Use a screwdriver and hammer to gently tap the plug from the outside until it falls into the disposal, then retrieve the plug from inside the disposal.
4. Inspect the entire length of the drain hose for any kinks, sharp bends, or clogs that could be restricting water flow.
5. Disconnect the drain hose and flush it with water to clear any debris. A mixture of baking soda and vinegar can help dissolve grease buildup.
6. Check the dishwasher’s filter, located at the bottom of the tub, and clean it thoroughly of any food particles or debris.
7. Once all connections are secured and the path is clear, restore power and run a ‘Rinse Only’ or ‘Drain’ cycle to test if the issue is resolved.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error FAE5 / F10E5
Error Code: FAE5 / F10E5 Difficulty: Hard

Problem: Indicates a leak has been detected, and the cycle has been canceled.

How to Fix FAE5 / F10E5 Error (Step-by-Step)
1. Immediately shut off the power to the dishwasher at the circuit breaker and turn off the water supply valve, which is usually under the sink.
2. The error indicates that the leak-detection sensor in the base pan of the dishwasher has been activated.
3. Carefully pull the dishwasher out from the cabinet and place towels down to absorb any spilled water.
4. Use a flashlight to inspect the area underneath for the source of the leak. Check hoses, the pump, and the sump housing for visible cracks or loose connections.
5. A common cause can be a damaged door seal or a crack in the spray arm. Inspect these components for wear and tear.
6. Because leaks can originate from multiple components, pinpointing the exact source can be difficult and may require disassembly of the unit.
7. To prevent potential water damage to your home and to ensure the correct part is replaced, it is safest to have a professional service perform this repair.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- W11613566
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: BLINKING
Error Code: FRONT STATUS LIGHT: BLINKING Difficulty: Easy

Problem: The cycle has been paused.

How to Fix FRONT STATUS LIGHT: BLINKING Error (Step-by-Step)
1. A blinking light means the wash cycle has been interrupted or paused.
2. Check to ensure the dishwasher door is closed completely and latched securely.
3. If the cycle was paused to add a dish, simply press the ‘Start/Resume’ button to continue the cycle.
4. If you have a ‘Delay Start’ option selected, the light may blink until the cycle is scheduled to begin.
5. Ensure that no dishes are blocking the door from closing or interfering with the detergent dispenser operation.
6. If the light continues to blink and the dishwasher will not start, try resetting the dishwasher by turning it off at the circuit breaker for one minute.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: BLUE
Error Code: FRONT STATUS LIGHT: BLUE Difficulty: Easy

Problem: Washing in-progress.

How to Fix FRONT STATUS LIGHT: BLUE Error (Step-by-Step)
1. This is not an error code. A solid blue light indicates that the dishwasher is currently in the middle of a wash or dry cycle.
2. No action is needed. The dishwasher is operating as expected.
3. Avoid opening the dishwasher door mid-cycle, as this will pause the operation and could affect cleaning performance.
4. The light will typically turn off once the entire cycle, including any drying period, is complete.
5. Refer to your specific model’s indicators to understand what different colors or lights mean during operation.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: RED
Error Code: FRONT STATUS LIGHT: RED Difficulty: Easy

Problem: Drying in-progress.

How to Fix FRONT STATUS LIGHT: RED Error (Step-by-Step)
1. Observe the red light on the front of the dishwasher; this indicates the drying cycle is in progress.
2. Avoid opening the dishwasher door to keep heat and steam inside for the best drying results.
3. Wait for the light to change to white or turn off, which signals the end of the cycle.
4. Once the light has changed, the cycle is complete and confirm the error stays cleared during a full test cycle.
5. You can now safely open the door and unload your dry dishes.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: WHITE
Error Code: FRONT STATUS LIGHT: WHITE Difficulty: Easy

Problem: Cycle completed.

How to Fix FRONT STATUS LIGHT: WHITE Error (Step-by-Step)
1. Notice the white light on the front of the dishwasher, which means the wash and dry cycles are finished.
2. Open the dishwasher door to begin unloading and confirm the error stays cleared during a full test cycle.
3. Be cautious of any remaining steam when you open the door.
4. The light will typically turn off after the door has been opened.
5. If the light remains on after unloading, pressing the ‘Cancel’ button should turn it off.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error OFB / OFB
Error Code: OFB / OFB Difficulty: Easy

Problem: Unbalanced load detected.

How to Fix OFB / OFB Error (Step-by-Step)
1. Press the ‘Cancel’ button to stop and drain the current cycle.
2. Open the door and look at how the dishes are arranged in the racks.
3. Reposition any large items like pots, pans, or bowls that may have shifted and could be blocking the spray arms.
4. Make sure dishes are not stacked on top of each other, which can prevent water from reaching all surfaces.
5. Gently spin the upper and lower spray arms with your hand to ensure they move freely.
6. Close the door firmly and select your desired cycle to restart the dishwasher.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026