Author: ApplianceFixGuide Team

  • How to Fix Amana Dryer Error E1

    How to Fix Amana Dryer Error E1

    Error Code: E1 Difficulty: Moderate

    Problem: Indicates an issue with the thermistor, specifically an open circuit. This can be caused by a faulty thermistor or a wiring problem.

    How to Fix E1 Error (Step-by-Step)

    1. Disconnect the dryer from the wall outlet to ensure safety.
    2. Access the thermistor, which is typically located on the blower housing. You may need to remove the lower front access panel by unscrewing it or releasing clips at the top.
    3. Locate the thermistor on the blower housing. It is a small black or gray component with a two-wire connector.
    4. Disconnect the wire harness attached to the thermistor. Squeeze the tab on the connector to release it.
    5. Remove the single screw, usually a quarter-inch hex head, that holds the thermistor in place.
    6. Install the new thermistor (Part: WP8577274), secure it with the screw, and firmly reconnect the wire harness.
    7. Reassemble the access panel, plug the dryer back in, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error CHECK VENT

    How to Fix Amana Dryer Error CHECK VENT

    Error Code: CHECK VENT Difficulty: Easy

    Problem: Indicates that the dryer vent is clogged or there is restricted airflow.

    How to Fix CHECK VENT Error (Step-by-Step)

    1. Pull out the dryer’s lint screen and clean it of all lint. If it has a waxy buildup from dryer sheets, wash it with a soft brush and soapy water, then let it dry completely.
    2. Unplug the dryer from the wall to ensure your safety during the next steps.
    3. Carefully pull the dryer away from the wall and detach the vent hose from the back of the machine.
    4. Clear any lint buildup from the dryer’s exhaust port and from the inside of the vent hose itself.
    5. Inspect the vent hose for any sections that are crushed or kinked, as this can severely limit airflow. Straighten them out.
    6. Use a specialized vent cleaning kit with a long brush to clean out the entire length of the ductwork that runs to the exterior of your home.
    7. Go outside and ensure the external vent flap is clean and can open and close without obstruction.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 88

    How to Fix Amana Dryer Error 88

    Error Code: 88 Difficulty: Easy

    Problem: All display segments are lit up. This is a normal part of the diagnostic test mode to ensure the display is working correctly.

    How to Fix 88 Error (Step-by-Step)

    1. This display is not an error but indicates the dryer is in a check test mode.
    2. To exit this mode, press and hold the ‘Start’ or ‘Cancel’ button for a few seconds.
    3. If the display does not return to normal, the next step is to reset the machine’s main board.
    4. Unplug the dryer from its power source for at least 2 minutes.
    5. Plug the dryer back in. The display should now be clear and ready for normal cycle selection.
    6. If the ’88’ display is stuck and will not clear after a power cycle, the display control board may be faulty and require professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 6E

    How to Fix Amana Dryer Error 6E

    Error Code: 6E Difficulty: Easy

    Problem: Service Required.

    How to Fix 6E Error (Step-by-Step)

    1. Attempt to clear the error by pressing the ‘Cancel’ or ‘Stop’ button on the control panel.
    2. If the code persists, unplug the dryer from the wall outlet or switch off the power at the home’s circuit breaker panel.
    3. Wait for a minimum of 5 minutes before restoring power. This process can reset the dryer’s internal checks.
    4. Plug the dryer back in or flip the circuit breaker on.
    5. Try to initiate a drying cycle and confirm the error stays cleared during a full test cycle.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 3E

    How to Fix Amana Dryer Error 3E

    Error Code: 3E Difficulty: Easy

    Problem: Service Required.

    How to Fix 3E Error (Step-by-Step)

    1. First, try to clear the code by pressing the ‘Stop’ or ‘Cancel’ button.
    2. If the code remains, perform a power cycle by unplugging the dryer from the electrical outlet or shutting it off at the circuit breaker.
    3. Let the dryer remain without power for at least 5 minutes. This allows the internal computer to perform a hard reset.
    4. Restore power by plugging the unit back in or turning the breaker on.
    5. Select a new cycle and press ‘Start’ to see if the error has cleared.
    6. If the ‘3E’ code returns, it signifies an internal component failure that requires diagnosis and repair by a professional service service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 3 BEEPS

    How to Fix Amana Dryer Error 3 BEEPS

    Error Code: 3 BEEPS Difficulty: Moderate

    Problem: Can indicate a variety of issues, including a problem with the door switch or water getting into the control panel.

    How to Fix 3 BEEPS Error (Step-by-Step)

    1. Disconnect the dryer from its power source by unplugging it from the wall outlet.
    2. Open the dryer door and locate the door switch, which is typically a small plastic switch around the frame that the door presses when closed.
    3. Check that the plastic peg or actuator on the door itself is not broken and aligns correctly with the switch.
    4. To replace the switch, you may need to remove the dryer’s top or front panel to access its housing and wiring.
    5. Carefully disconnect the wire harness from the old switch, release the locking tabs, and install the new one.
    6. Reassemble the dryer, restore power, and test its operation and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WP3406107

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 0E

    How to Fix Amana Dryer Error 0E

    Error Code: 0E Difficulty: Moderate

    Problem: Indicates that there is too much water in the appliance. This could be due to a blocked pump or a faulty hot water valve that is not shutting off.

    How to Fix 0E Error (Step-by-Step)

    1. Turn off the hot and cold water supply valves connected to the appliance.
    2. Unplug the dryer from the wall outlet to ensure safety.
    3. Check the drain hose at the back for any visible kinks, twists, or blockages that could restrict water flow.
    4. Place the end of the drain hose into a bucket to catch any trapped water and clear it from the line.
    5. Inspect the water inlet hoses for any signs of damage, wear, or leaks.
    6. This error often points to a faulty internal water pump or a stuck water inlet valve. These repairs involve handling water and electrical parts, so it is recommended to have a professional service service diagnose and complete the repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error -:–

    How to Fix Amana Dryer Error -:–

    Error Code: -:– Difficulty: Easy

    Problem: Dashes in the display can indicate a control panel issue or that the dryer is in a diagnostic mode. A power cycle is recommended.

    How to Fix -:– Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet or turn it off at the circuit breaker.
    2. Wait for 5 minutes to allow the internal electronics to fully discharge and reset.
    3. Plug the dryer back in or switch the circuit breaker on.
    4. Attempt to start a normal drying cycle to see if the code has been cleared.
    5. If the dashes reappear on the display, this indicates a more serious issue with the main control board.
    6. Due to the complexity and risk of working with electronic components, replacement of the control board should be performed by a qualified appliance service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error UL

    How to Fix Amana Washer Error UL

    Error Code: UL Difficulty: Hard

    Problem: Unbalanced Load

    How to Fix UL Error (Step-by-Step)

    1. Unplug the washer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Open the washer lid and redistribute the clothes evenly around the wash plate. Avoid washing single, heavy items by themselves.
    3. Close the lid and plug the washer back in. Try running a spin cycle. If the error persists, proceed to the next step.
    4. To inspect the suspension, you will need to lift the top panel of the washer. Use a putty knife to release the two clips on the front edge.
    5. With the top panel lifted, you can see the four suspension rods, one at each corner of the tub. Check if any of the rods appear broken or disconnected. Gently press down on the tub to see if it bounces excessively, which indicates weak suspension.
    6. To replace a suspension rod, lift the rod up from the tub bracket, then disconnect it from the top support cup. Install the new rod by reversing these steps.
    7. If the suspension rods are intact, the issue may be with the drive hub or gearcase, which typically requires a professional service.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10780048
    • W10821956
    • W11130362

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error RL

    How to Fix Amana Washer Error RL

    Error Code: RL Difficulty: Easy

    Problem: Items detected in the washer during the Clean Washer cycle.

    How to Fix RL Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the ‘Clean Washer’ cycle.
    2. Wait for the washer lid to unlock and confirm the error stays cleared during a full test cycle.
    3. Open the lid and remove any clothing or other items that were left inside the washer tub.
    4. Close the lid securely and confirm the error stays cleared during a full test cycle.
    5. Select the ‘Clean Washer’ cycle again and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start’ button to begin the cycle without any items in the tub.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes