Author: ApplianceFixGuide Team

Problem: Door switch circuit intermittent or control board door sense circuit failure

How to Fix Dryer Error

1. Unplug dryer and remove front lower panel to access door switch WPW10441007 wiring harness.
2. Inspect harness for pinched wires near door hinge area—common failure point from repeated door opening/closing.
3. Disconnect harness at switch and at control board—test continuity of each wire with multimeter. Repair any broken wires with high-temperature wire nuts.
4. Test door switch operation per F5E1 procedure—replace WPW10441007 if faulty.
5. If switch and wiring test good, fault may be in control board door sense circuit.
6. Inspect control board WPW10111608 connector pins for corrosion—clean with electronic contact cleaner if needed.
7. Reseat door switch harness connector firmly on control board.
8. Power on and test door operation multiple times (open/close 10x) to verify intermittent issue resolved.
9. If error returns after switch/wiring repair, control board WPW10111608 must be replaced.
10. After repair, verify dryer starts reliably with door closed and stops immediately when door opens during operation.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Airflow restriction detected by control system—equivalent to F4E3

How to Fix Dryer Error

1. Power off dryer and remove lint screen—clean thoroughly under warm running water to dissolve fabric softener residue, scrub gently with soft brush, rinse completely, and dry before reinstalling.
2. Disconnect flexible vent hose from dryer exhaust outlet—inspect entire length for kinks, crushing, or lint blockages. Use dryer vent cleaning brush kit to remove lint buildup.
3. Inspect exterior vent termination—remove cover and clean flapper mechanism, verify no bird nests or debris inside vent pipe.
4. Measure total vent run length—should not exceed 40 feet equivalent (subtract 5 feet for each 90° elbow,
5. 5 feet for each 45° elbow).
6. Remove rear panel and inspect blower wheel housing—vacuum all lint buildup around wheel and housing interior.
7. Inspect blower wheel for cracks, missing fins, or wobble on shaft—replace if damaged (WPW
8. .
9. Check drum front and rear seals for tears allowing air bypass—replace if damaged.
10. Reconnect vent system with minimal bends and proper support clamps.
11. Run test cycle on timed dry (bypassing moisture sensor) and verify strong, hot airflow at exterior vent.
12. Error clears automatically after successful cycle with adequate airflow—no button press required.

Browse all Maytag error codes: Maytag Error Codes

Problem: Power failure interrupted drying cycle—temporary loss of household electricity

How to Fix Dryer Error

1. Verify household power is restored—check other appliances on same circuit.
2. Check circuit breaker panel for tripped dryer breaker—reset by turning fully OFF then ON.
3. Inspect power cord for damage or loose connections at terminal block inside dryer (remove rear panel to access).
4. Tighten terminal block screws if loose—should require firm pressure to secure (approximately 35 in-lbs torque).
5. To resume cycle: press and hold START button for 3 seconds, OR press POWER button to clear display then reselect cycle and press START.
6. If PF code returns frequently without actual power outages, inspect house wiring: loose neutral connection at breaker panel can cause intermittent power loss. Contact licensed electrician if suspected.
7. Test voltage at dryer outlet with multimeter—should read 240V±10% under load. Voltage below 220V can cause control board resets mimicking PF code.
8. If voltage stable but PF recurs, inspect control board WPW10111608 for failing power supply section—replace if other causes eliminated.

Browse all Maytag error codes: Maytag Error Codes

Problem: Missing L2 leg of 240V power supply—dryer runs but heater won’t operate

How to Fix Dryer Error

1. Disconnect power at circuit breaker.
2. Remove rear panel to access power cord terminal block.
3. Restore power and carefully measure voltage at terminal block: L1 to Neutral = 120V, L2 to Neutral = 120V, L1 to L2 = 240V.
4. If L1-L2 reads 120V instead of 240V, L2 leg is missing—check circuit breaker for partial trip (one pole tripped while other remains on). Reset breaker fully OFF then ON.
5. If breaker reset doesn’t restore 240V, test voltage directly at breaker output terminals—call electrician if voltage missing at breaker (indicates panel wiring fault).
6. If voltage correct at terminal block but not reaching heater, test thermal fuse WP3392519 on blower housing for continuity—replace if open (common failure when L2 leg intermittently missing causes motor to overheat).
7. Check high-limit thermostat WP3392914 for continuity—replace if open.
8. Inspect wiring between terminal block and heater for loose connections or burnt terminals—repair as needed.
9. After repair, verify 240V at heating element terminals during heat cycle.
10. Monitor exhaust temperature to confirm proper heating operation—should reach 135-155°F on cotton setting.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Door not fully closed/latched or door switch not detecting closed position

How to Fix Dryer Error

1. Open and firmly reclose dryer door—listen for distinct latch click.
2. Inspect door gasket for tears, folds, or debris preventing full closure—clean or replace as needed.
3. Check door strike plate alignment on front panel—should engage latch mechanism fully without binding.
4. Manually test door switch operation: with door closed, gently press on door near latch area—dryer should start if switch was marginally engaged.
5. If door appears fully closed but error persists, unplug dryer and remove front lower panel to access door switch WPW
6. Inspect switch plunger alignment—door strike must fully depress plunger when closed. Adjust strike plate position if misaligned (loosen mounting screws slightly and reposition).
7. Test door switch continuity with multimeter—replace WPW10441007 if faulty (see F5E1 procedure).
8. Check door hinge screws for looseness—tighten if door sags preventing proper closure.
9. After adjustments, close door firmly and press START—error should clear automatically.
10. If error returns consistently, control board door sense circuit may be faulty—replace WPW10111608 after verifying switch and wiring.

Browse all Maytag error codes: Maytag Error Codes

Problem: Thermistor short circuit—Neptune series display code equivalent to F3E3

How to Fix Dryer Error

1. Unplug Neptune dryer and remove front lower panel (typically 4 screws at bottom front).
2. Locate thermistor WP35001191 mounted on blower housing near air inlet.
3. Disconnect wiring harness from thermistor terminals.
4. Set multimeter to resistance mode and measure across thermistor leads at room temperature.
5. Normal reading: 10k-12k ohms at 70°F. tS code indicates short circuit—reading below 500 ohms.
6. Inspect thermistor body for cracks, moisture damage, or physical deformation causing internal short.
7. Remove mounting screw securing thermistor to housing.
8. Extract old thermistor and install new WP35001191, ensuring sensor tip protrudes fully into air stream path.
9. Reconnect wiring harness with terminals fully seated—verify no exposed wire strands.
10. To clear tS code: press and hold SENSOR DRY LEVEL and TIME buttons simultaneously for 3 seconds until display resets.
11. Run test cycle to verify proper temperature monitoring.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Thermistor short circuit—Neptune series alternate display for tS code

How to Fix Dryer Error

1. Unplug Neptune dryer and remove front lower panel to access blower housing.
2. Locate thermistor WP35001191 mounted on air inlet duct.
3. Disconnect wiring harness and measure resistance with multimeter—short circuit indicated by reading below 500 ohms (normal: 10k-12k ohms at room temp).
4. Remove mounting screw and extract faulty thermistor.
5. Install new thermistor WP35001191 ensuring proper seating in mounting hole with sensor tip facing airflow.
6. Reconnect wiring harness securely.
7. To clear t5 code: press and hold SENSOR DRY LEVEL and TIME buttons simultaneously for 3 seconds until display resets to normal.
8. Power on dryer and select any cycle—error should not return.
9. Run test cycle monitoring drying performance—cycle should terminate appropriately based on load moisture content.
10. If t5 returns after replacement, inspect wiring harness for short circuit between thermistor and control board—repair or replace harness as needed.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Diagnostic code: Door sense circuit failure on control board or power line interference

How to Fix Dryer Error

1. Enter diagnostic mode per model procedure (typically hold CHIME + TEMPERATURE buttons 3 seconds).
2. Observe if d1 appears consistently or intermittently—intermittent suggests wiring issue; consistent suggests board failure.
3. Unplug dryer and remove front lower panel to access door switch WPW10441007 wiring.
4. Inspect harness for damage near door hinge—repair any broken wires with high-temperature connectors.
5. Test door switch continuity—replace WPW10441007 if faulty.
6. Disconnect door switch harness at control board WPW10111608 and inspect pins for corrosion—clean with contact cleaner.
7. Reseat connector firmly and exit diagnostic mode.
8. If d1 returns immediately, control board door sense circuit has failed—replace WPW
9. After replacement, re-enter diagnostic mode and verify d1 code no longer appears in fault history.
10. Run full diagnostic cycle to confirm all sensors and actuators function correctly.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Diagnostic code: Motor circuit failure—open winding or failed start capacitor

How to Fix Dryer Error

1. Enter diagnostic mode and run motor test cycle—note if motor hums but won’t start (capacitor) or remains silent (open winding).
2. Unplug dryer and remove rear panel to access motor WPW
3. Disconnect wiring harness from motor terminals.
4. Set multimeter to resistance mode and test windings: Main winding (typically terminals 1-
5. should read 2-6 ohms; Start winding (terminals 2-
6. should read 4-8 ohms. Infinite resistance indicates open winding—replace motor.
7. Test start capacitor (typically 5-8 MFD) with capacitance meter—reading below 80% of rated value indicates weak capacitor.
8. If capacitor weak but windings good, replace capacitor WP3392519 ($
9. .
10. If windings open or shorted, replace entire motor assembly WPW
11. During installation, verify blower wheel is securely fastened to motor shaft (setscrew tight).
12. Reconnect wiring harness ensuring correct terminal assignment per wiring diagram.
13. Exit diagnostic mode and run test cycle—motor should start immediately and run smoothly without overheating.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Diagnostic code: Coin mechanism circuit error (commercial models) or control board relay failure

How to Fix Dryer Error

1. For residential models without coin mechanism, d5 indicates control board relay failure.
2. Unplug dryer and remove rear panel to access control board WPW
3. Inspect board for burnt components near relay banks—especially motor and heater relays.
4. Test relay coils for continuity (80-150 ohms typical)—infinite resistance indicates open coil.
5. Test relay contacts for proper operation: de-energized = open circuit; energized = continuity.
6. If any relay fails tests, control board must be replaced—relays are not serviceable individually.
7. For commercial coin-op models: inspect coin mechanism wiring harness for damage, verify harness fully connected to control board, clean coin acceptor mechanism of debris.
8. Replace control board WPW10111608 with exact model match.
9. After installation, enter diagnostic mode and run all actuator tests to verify proper relay operation.
10. Clear fault history per service manual procedure to prevent d5 from reappearing on display.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes