Author: ApplianceFixGuide Team

  • How to Fix Frigidaire Washer Error E4

    How to Fix Frigidaire Washer Error E4

    Error Code: E4 Difficulty: Easy

    Problem: The washer is out of balance.

    How to Fix E4 Error (Step-by-Step)

    1. Press the pause button to stop the cycle and wait for the door to unlock.
    2. Open the door and redistribute the laundry load, moving items around so they are spread evenly inside the drum.
    3. Avoid washing single heavy items, like a bath mat, by themselves. Add a few towels to balance the load.
    4. Check if the washer is level by placing a bubble level on top of the machine. Check front-to-back and side-to-side.
    5. Adjust the washer’s leveling feet at each corner by screwing them up or down until the machine is stable and level.
    6. Tighten the lock nuts on the leveling feet against the base of the washer to secure them in place.
    7. Close the door and resume the wash cycle and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E32

    How to Fix Frigidaire Washer Error E32

    Error Code: E32 Difficulty: Moderate

    Problem: Water level pressure sensor isn’t communicating with the electronic control board or there is a pressure sensor calibration problem.

    How to Fix E32 Error (Step-by-Step)

    1. Disconnect the washer from the wall outlet to ensure your safety during the repair.
    2. To access the internal components, you will typically need to remove the top panel of the washer by unscrewing fasteners at the back.
    3. Locate the water level pressure sensor; it is a small, round part with a thin air hose and a wire connector attached.
    4. Carefully disconnect the wire harness by pressing its release tab and pull the thin rubber air hose off the sensor’s port.
    5. Remove the screw or release the clip holding the sensor to the washer’s chassis and remove the old sensor.
    6. Mount the new pressure sensor, then firmly reconnect the air hose and the electrical wire harness.
    7. Reinstall the top panel, plug the washer in, and run a test cycle to confirm the fix.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E3

    How to Fix Frigidaire Washer Error E3

    Error Code: E3 Difficulty: Easy

    Problem: The lid is open or there is a door lock problem.

    How to Fix E3 Error (Step-by-Step)

    1. Open the washer door and then close it again, pushing firmly to ensure it is securely latched.
    2. Listen for a distinct ‘click’ sound which indicates the door lock has engaged properly.
    3. Inspect the area around the door lock mechanism for any obstructions like fabric from clothing, lint buildup, or dirt.
    4. Use a damp cloth to wipe down the door, the rubber seal, and the lock assembly to ensure a clean contact surface.
    5. As a reset, unplug the washer from the electrical outlet for five minutes.
    6. Plug the washer back in and attempt to start a new cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E2

    How to Fix Frigidaire Washer Error E2

    Error Code: E2 Difficulty: Easy

    Problem: The washer is not draining.

    How to Fix E2 Error (Step-by-Step)

    1. Examine the drain hose behind the washer to ensure it is not kinked, clogged, or improperly positioned.
    2. Confirm the end of the drain hose is no more than 8 inches into the standpipe or laundry sink to prevent siphoning.
    3. Locate the drain pump filter access door, typically on the bottom front of the washer.
    4. Place a shallow pan and towels underneath the access door to catch water before twisting the filter cap counter-clockwise.
    5. Slowly remove the filter and clean it of any lint, coins, hair, or other foreign objects that may be causing a blockage.
    6. Securely screw the filter back into place, ensuring a tight seal to prevent leaks.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E1

    How to Fix Frigidaire Washer Error E1

    Error Code: E1 Difficulty: Easy

    Problem: Water is not entering the washer or the fill time is slow.

    How to Fix E1 Error (Step-by-Step)

    1. Verify that both the hot and cold water faucets supplying the washer are turned on completely.
    2. Inspect the full length of the water inlet hoses for any kinks, twists, or crushing that could restrict water flow and straighten them.
    3. Turn off the water supply faucets and unscrew the inlet hoses from the back of the washer.
    4. Check the small metal filter screens inside the washer’s water inlet ports for any sediment or debris.
    5. Use a small brush or pliers to gently remove the screens and rinse them thoroughly under clean water until all debris is gone.
    6. Reinstall the filter screens, securely reconnect the hoses, and turn the water faucets back on.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Whirlpool Dryer Error F31

    How to Fix Whirlpool Dryer Error F31

    Problem: Low L2 Voltage (Legacy)

    How to Fix F31 Error

    1. Go to your home’s circuit breaker panel and locate the two breakers for the dryer.
    2. Turn both breakers fully OFF, wait 10 seconds, and turn them back ON.
    3. If the error persists, a multimeter is required to test the wall outlet for 240 volts (L1 to L
    4. .

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F30

    How to Fix Whirlpool Dryer Error F30

    Problem: Restricted Airflow (Legacy)

    How to Fix F30 Error

    1. Remove and clean the lint screen thoroughly with warm water and soap to remove invisible fabric softener residue.
    2. Disconnect the dryer vent hose from the wall and vacuum out the exhaust duct.
    3. Check the outside vent hood to ensure flappers open freely and are not blocked by lint.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Maytag Washer Error F3E5

    How to Fix Maytag Washer Error F3E5

    Problem: Water temperature too high during rinse; hoses likely reversed

    How to Fix F3E5 Error

    1. Verify inlet hoses are connected correctly (Hot to Hot, Cold to Cold) on back of washer.
    2. Run hot water tap at nearest sink to purge cold water from line.
    3. Inspect and clean mesh screens on water inlet valve.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Washer Error F34

    How to Fix Maytag Washer Error F34

    Problem: Items detected during Clean Washer cycle (numeric equivalent of rL)

    How to Fix F34 Error

    1. Open lid/door and remove any clothing or items found in drum.
    2. The ‘Clean Washer’ cycle must be run with an empty basket.
    3. Restart the Clean Washer cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Washer Error F0E7

    How to Fix Maytag Washer Error F0E7

    Problem: Basket re-engagement failure; multiple cycles without opening lid

    How to Fix F0E7 Error

    1. Open and firmly close the lid to ensure the magnetic switch engages.
    2. Run a ‘Clean Washer’ cycle or a short cycle with no clothes to reset sensor logic.
    3. Ensure washer is empty before starting next cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes