Author: ApplianceFixGuide Team

  • How to Fix Frigidaire Washer Error E24

    How to Fix Frigidaire Washer Error E24

    Error Code: E24 Difficulty: Hard

    Problem: Problem with the drain pump relay.

    How to Fix E24 Error (Step-by-Step)

    1. Unplug the washing machine from its power source and confirm the error stays cleared during a full test cycle.
    2. Slide the washer forward and remove the top panel by unscrewing it from the back.
    3. Identify the main control board. It will have numerous wire harnesses connected to it.
    4. To avoid errors, take a detailed picture of all the connections before you begin unplugging anything.
    5. Systematically disconnect each wire harness from the old board. Pay attention to the small plastic locking clips on each connector.
    6. Unscrew the old control board from its mounting points and carefully lift it out.
    7. Secure the new main control board in place, reconnect all wires based on your reference photo, and reattach the top panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E23

    How to Fix Frigidaire Washer Error E23

    Error Code: E23 Difficulty: Hard

    Problem: The drain pump relay on the control board has failed.

    How to Fix E23 Error (Step-by-Step)

    1. Disconnect the washer from the power source and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel of the washer by taking out the screws at the back.
    3. Locate the main control board, which is typically a plastic-encased circuit board with many wires connected to it.
    4. Take a clear photo of the wire connections to the board to use as a reference.
    5. Carefully disconnect all wire harnesses from the old control board. They have locking tabs that need to be pressed.
    6. Remove the mounting screws holding the control board in place and install the new board.
    7. Reconnect all wire harnesses to the new board according to your photo, replace the top panel, and restore power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E14

    How to Fix Frigidaire Washer Error E14

    Error Code: E14 Difficulty: Moderate

    Problem: Problem with the reed switch.

    How to Fix E14 Error (Step-by-Step)

    1. Unplug the washer from the wall outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the screws from the top panel of the washer, usually located at the back, and slide the panel off.
    3. Locate the reed switch, which is a small magnetic switch typically found near the dispenser drawer housing.
    4. Disconnect the wire connector attached to the reed switch and confirm the error stays cleared during a full test cycle.
    5. Remove the old reed switch, which may be held by a clip or a single screw.
    6. Install the new reed switch, reconnect its wire connector, and ensure it is secure.
    7. Replace the top panel and secure it with its screws before plugging the washer back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E13

    How to Fix Frigidaire Washer Error E13

    Error Code: E13 Difficulty: Hard

    Problem: Water leak in the tub or air leak in the pressure sensor air hose.

    How to Fix E13 Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet and turn off the water supply valves.
    2. Disconnect the hot and cold water hoses and the drain hose from the back of the washer.
    3. Carefully tilt the washer backwards and prop it securely against a wall to access the bottom.
    4. Locate the drain pump at the bottom of the machine. Disconnect the wire harness and the hoses attached to it, having a towel ready for residual water.
    5. Remove the screws mounting the old drain pump and install the new one in its place.
    6. Reconnect the hoses and wire harness to the new pump.
    7. Carefully set the washer upright, reconnect all hoses, and plug it back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137221600 (Drain Pump)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E10

    How to Fix Frigidaire Washer Error E10

    Error Code: E10 Difficulty: Easy

    Problem: Water is not entering the washer fast enough.

    How to Fix E10 Error (Step-by-Step)

    1. Turn off the water supply to the washer at the wall valves.
    2. Unscrew the hot and cold water hoses from the back of the machine.
    3. Check the small metal filter screens inside the water inlet ports on the washer for any sediment or debris.
    4. Clean the screens thoroughly with a small brush and water.
    5. Check the entire length of both water hoses for any kinks or twists that could block water flow and straighten them.
    6. Reconnect the hoses securely and turn the water supply back on.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E59

    How to Fix Frigidaire Washer Error E59

    Error Code: E59 Difficulty: Hard

    Problem: No tacho signal for 3 seconds.

    How to Fix E59 Error (Step-by-Step)

    1. Disconnect the washer from its power supply by unplugging it from the wall.
    2. Remove the service panel, typically at the rear of the washer, to access the drive motor.
    3. Locate the wire harness that connects from the motor to the motor control board. The tachometer signal travels through this harness.
    4. Inspect the harness for any damage and ensure it is securely plugged in at both the motor and the control board.
    5. The tachometer is an internal component of the drive motor and is not sold separately.
    6. If the wiring is intact, the entire drive motor must be replaced to fix the faulty tachometer.
    7. Install the new motor, reconnect the drive belt and wiring, reassemble the washer, and test for proper operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E58

    How to Fix Frigidaire Washer Error E58

    Error Code: E58 Difficulty: Hard

    Problem: High current on motor phase.

    How to Fix E58 Error (Step-by-Step)

    1. Unplug the washing machine from the electrical outlet to ensure safety.
    2. Gain access to the motor and motor control board, usually by removing a rear or bottom service panel.
    3. Carefully inspect the wiring that runs between the drive motor and the motor control board. Look for any signs of damage, chafing, or loose connections.
    4. A service would test the motor’s electrical windings with a multimeter to check for shorts or open circuits.
    5. If the motor windings are out of specification, the entire drive motor assembly needs to be replaced.
    6. If the motor tests correctly, the issue points to a faulty motor control board, which must be replaced.
    7. After replacing the diagnosed part, reassemble the washer, plug it in, and run a spin cycle to verify the repair.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134743500 (Motor Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E57

    How to Fix Frigidaire Washer Error E57

    Error Code: E57 Difficulty: Hard

    Problem: High current on inverter.

    How to Fix E57 Error (Step-by-Step)

    1. Turn off the circuit breaker for the washer and unplug it from the wall outlet.
    2. Remove the rear access panel of the washer to locate the motor control board (inverter), which is situated near the bottom of the machine.
    3. Take a clear photo of the wire connections to the board for reference before disconnecting anything.
    4. Carefully disconnect all wire harnesses leading to the motor control board.
    5. Remove the mounting screws that hold the control board in place and lift the old board out of the washer.
    6. Install the new motor control board, securing it with the mounting screws.
    7. Reconnect all wire harnesses according to your reference photo, reattach the access panel, and restore power to test the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E56

    How to Fix Frigidaire Washer Error E56

    Error Code: E56 Difficulty: Hard

    Problem: High motor current.

    How to Fix E56 Error (Step-by-Step)

    1. Disconnect the washer from its power source by unplugging the cord from the wall.
    2. Access the bottom of the washer, which may require carefully tilting the machine back and propping it up securely.
    3. Locate the drive motor and the motor control board. Visually inspect both for burn marks, melted connectors, or damaged wires.
    4. Ensure the wire harness connecting the motor to the control board is securely plugged in at both ends.
    5. A professional would use a multimeter to test the motor windings for continuity. If the motor fails the test, it requires replacement.
    6. If the motor tests good, the failure is likely in the motor control board, which will need to be replaced.
    7. After replacing the faulty component (either the motor or the control board), reassemble the washer and test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134743500 (Motor Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E4A

    How to Fix Frigidaire Washer Error E4A

    Error Code: E4A Difficulty: Moderate

    Problem: Control detects a problem with the door lock circuit.

    How to Fix E4A Error (Step-by-Step)

    1. Unplug the washer from the power outlet to prevent electrical shock.
    2. Open the washer door. Use a screwdriver to pry off the outer spring clamp that holds the rubber door boot seal to the front panel.
    3. Peel the door boot away from the front panel around the door lock area to gain access to the lock assembly.
    4. Disconnect the electrical wire connector from the door lock assembly.
    5. Remove the screws that mount the door lock assembly to the washer’s front panel and take out the old part.
    6. Install the new door lock assembly, secure it with the mounting screws, and reconnect the wire harness.
    7. Re-secure the door boot seal with the spring clamp, plug in the washer, and test the door lock.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Frigidaire error codes: Frigidaire Error Codes