Author: ApplianceFixGuide Team

How to Fix Whirlpool Washer Error F8E1
Problem: Long fill error – water not entering washer fast enough or pressure switch fault

How to Fix Washer Error
1. Verify both hot/cold water supply valves are fully open and household water pressure is >20 PSI.
2. Disconnect fill hoses and check flow rate into bucket (should fill 1 gallon in <15 seconds).
3. Clean inlet valve screens by removing hoses and brushing debris from brass fittings.
4. Inspect fill hoses for kinks, excessive length (>6 feet), or internal collapse restricting flow.
5. Remove top panel and locate pressure switch on right side wall.
6. Disconnect pressure hose and blow through it to clear moisture/debris blocking air passage.
7. Verify pressure hose connection at air dome on tub isn’t clogged with detergent residue.
8. If water flow is adequate but error persists, replace water inlet valve assembly W
9. If inlet valve tests good, replace pressure switch W
10. After repair, verify washer fills to proper level within 6 minutes on normal cycle.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error F8E3
Problem: Water temperature sensor circuit fault – out of range reading

How to Fix Washer Error
1. Unplug washer and remove lower front panel.
2. Locate temperature sensor (NTC thermistor) mounted on outer tub near heater.
3. Disconnect sensor connector and measure resistance with multimeter.
4. At room temperature (77°F/25°C), resistance should be approximately 10kΩ ±5%.
5. Dip sensor tip in ice water – resistance sould increase to ~35kΩ.
6. Dip sensor tip in hot water (120°F) – resistance should decrease to ~
7. 5kΩ.
8. If resistance readings are infinite, zero, or don’t change with temperature, replace sensor W
9. Inspect wiring harness between sensor and control board for damage or rodent chewing.
10. Verify connector pins aren’t corroded or bent.
11. After replacement, run hot water cycle and verify displayed temperature increases steadily during fill.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Dryer Error F73
Problem: User interface communication timeout

How to Fix Dryer Error
1. Turn off power at circuit breaker.
2. Remove control panel faceplate and access cover.
3. Inspect all communication connectors between boards.
4. Check ribbon cables for damage, bent pins, or loose connections.
5. Test communication signals with multimeter if possible.
6. Clean all electrical contacts with contact cleaner.
7. If connections are good but error persists, replace user interface board.
8. Document all wire connections before disconnecting.
9. Install new user interface board assembly.
10. Test all functions and run diagnostic communication tests.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Dishwasher Error F03
Problem: Temperature sensor (thermistor) malfunction

How to Fix Dishwasher Error
1. Unplug dishwasher and access temperature sensor.
2. Test thermistor resistance at room temperature (should be ~11k ohms).
3. Check wiring harness for damage or loose connections.
4. Verify sensor is properly immersed in water.
5. Replace thermistor if readings are out of specification.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error F8E4
Problem: Leak detection – float switch activated indicating water in base pan

How to Fix Washer Error
1. Unplug washer immediately and turn off water supply valves.
2. Tilt washer backward 45 degrees to access base pan (place wood blocks under front feet).
3. Remove 3 screws securing base pan and lower carefully – expect standing water.
4. Dry base pan completely with towels and shop vacuum.
5. Locate source of leak: inspect inlet valve connections, drain pump seals, tub gasket, and hoses.
6. Run washer briefly with water supply on to observe leak source (use flashlight).
7. Common culprits: cracked drain pump housing, loose hose clamp, or torn tub seal.
8. Replace leaking component (pump W11399437, hose WPW10351854, or tub seal W
9. .
10. Verify float switch resets after pan is dry (should show open circuit when dry).
11. Reinstall base pan and test washer through complete cycle monitoring for leaks.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error F8E5
Problem: Heater relay stuck closed – continuous heating detected

How to Fix Washer Error
1. UNPLUG WASHER IMMEDIATELY – stuck relay creates fire hazard and can boil water.
2. Remove lower front panel to access heater element on outer tub.
3. Disconnect wiring harness from heater terminals.
4. Verify heater is cold to touch (if hot with washer off, relay is definitely stuck).
5. Remove top panel to access main control board (CCU).
6. Locate heater relay on board (typically large blue or black component near edge).
7. Visually inspect relay for burnt contacts or melted housing.
8. DO NOT attempt to repair relay – replace entire main control board assembly W
9. Before installing new board, verify heater element resistance is normal (15-25 ohms) to prevent immediate failure of new relay.
10. After replacement, run diagnostic heat cycle monitoring temperature rise rate (should heat 1°F per minute maximum).
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Washer Error F16
Problem: Door lock error – multiple attempts to lock failed

How to Fix Washer Error
1. Turn off power supply.
2. Open washer door fully.
3. Inspect door lock assembly for physical damage or debris.
4. Check door strike plate alignment with lock mechanism.
5. Test door lock solenoid resistance with multimeter.
6. Check wiring harness for damage or loose connections.
7. If lock assembly is faulty, disconnect electrical connector.
8. Remove mounting screws and replace door lock assembly.
9. Ensure proper alignment during installation.
10. Test door lock function multiple times to verify reliability.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Dishwasher Error F04
Problem: Water inlet valve failure or restriction

How to Fix Dishwasher Error
1. Check water supply pressure (should be 20-120 PSI).
2. Inspect inlet valve screen for debris blockage.
3. Test valve solenoid for continuity (should read 800-1200 ohms).
4. Verify voltage to valve during fill cycle.
5. Replace inlet valve assembly if faulty.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error F9E1
Problem: Long drain error. The machine tried to pump water out but the sensor still detects water. Clean the drain pump filter and check for kinks in the drain hose.

How to Fix F9E1 Error
1. - UNPLUG washer from electrical power for 5 minutes to reset lock mechanism.
  - Attempt manual door release: insert flat tool through dispenser opening to pull lock release tab downward.
  - Remove top panel (3 rear screws) and front control panel to access door lock assembly.
  - Inspect lock latch for debris, damage, or misalignment. Clean with isopropyl alcohol.
  - Test door lock solenoid resistance with multimeter: should read 150-300Ω. Check microswitch continuity during manual operation.
  - If resistance is out of range or microswitch fails, replace door lock assembly using OEM part W
  - Disconnect wiring harness. Remove mounting screws. Extract old lock assembly.
  - Install new lock assembly. Ensure strike plate on door aligns perfectly with latch.
  - Reassemble panels. Restore power. Run door lock test cycle to verify engagement/disengagement sounds and operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Dryer Error F72
Problem: User interface display failure

How to Fix Dryer Error
1. Disconnect power at circuit breaker.
2. Remove control panel faceplate and access cover.
3. Inspect display connections for loose or corroded connectors.
4. Test display backlight and segment operation.
5. Check ribbon cable connections between display and interface board.
6. Clean electrical contacts with contact cleaner.
7. If display is faulty, disconnect ribbon cable.
8. Remove mounting screws and replace display assembly.
9. Reconnect ribbon cable and test display functions.
10. Run diagnostic mode to verify proper display operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026