Author: ApplianceFixGuide Team

How to Fix Kenmore Washer Error F0E3
Problem: User interface control board communication error

How to Fix Washer Error
1. Disconnect power at circuit breaker.
2. Remove control panel faceplate and access cover.
3. Inspect user interface board connectors for corrosion or damage.
4. Check ribbon cable connections between interface and main control.
5. Test communication signals with multimeter if possible.
6. Clean all electrical contacts with contact cleaner.
7. If connections are good but error persists, replace user interface board.
8. Document all wire connections before disconnecting.
9. Install new user interface board assembly.
10. Test all button functions and display operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F10
Problem: Motor Control Unit (MCU) Heat Sink Overheat

How to Fix Washer Error
1. Unplug the washer from power source.
2. Remove the dispenser drawer completely to access the inlet valve area.
3. Turn off both hot and cold water supply valves at the wall.
4. Disconnect the water inlet hoses from the back of the washer, having towels ready for spills.
5. Remove the top panel by unscrewing the rear mounting screws.
6. Locate the water inlet valve assembly at the back of the washer.
7. Disconnect the electrical connectors from the valve solenoids.
8. Remove the mounting screws securing the inlet valve assembly.
9. Inspect the old valve for mineral buildup or damaged solenoids.
10. Install the new inlet valve assembly, ensuring all electrical connectors are secure.
11. Reconnect water hoses, turn on supply valves slowly, check for leaks, and test fill function.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F08
Problem: Heater Circuit / Steam Element Failure

How to Fix Washer Error
1. Unplug the washer and turn off water supply valves.
2. Remove the top panel and control panel to access the main control board area.
3. Check all wire harness connections for loose or damaged wires.
4. Remove the rear access panel to inspect the motor control unit connections.
5. Disconnect the power cord and remove mounting screws from the main control board.
6. Carefully label and disconnect all wire harnesses from the control board.
7. Remove the old control board and inspect for any visible damage.
8. Install the new control board, ensuring all connectors are properly aligned.
9. Reconnect all harnesses according to your labels.
10. Reassemble panels and perform a system reset by unplugging for 5 minutes before testing all functions.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F05
Problem: Water Temperature Sensor / Heating System

How to Fix Washer Error
1. Unplug the washer completely from power.
2. Remove the front lower access panel to access the door lock assembly.
3. Locate the door latch mechanism behind the door strike plate.
4. Disconnect the electrical connector from the door lock assembly.
5. Remove the mounting screws securing the door lock to the front panel.
6. Carefully pull out the door lock assembly, noting the position of any actuator rods.
7. Inspect the old lock for broken parts or worn contacts.
8. Install the new door lock assembly, ensuring the actuator rods align properly with the door mechanism.
9. Reconnect the electrical connector and secure mounting screws.
10. Test the door lock by closing the door and starting a cycle to verify it locks and unlocks properly.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F03
Problem: Pressure Sensor / Water Level Detect Error

How to Fix Washer Error
1. Unplug the washer from power.
2. Remove the top panel by unscrewing the rear mounting screws.
3. Locate the pressure switch (water level sensor) usually mounted on the right side wall.
4. Disconnect the thin air pressure hose from the switch and blow through it to check for blockages.
5. Remove the electrical connectors from the pressure switch terminals.
6. Unscrew the mounting screws holding the pressure switch in place.
7. Install the new pressure switch and reconnect the air hose securely.
8. Reconnect the electrical connectors ensuring they click into place.
9. Reassemble the top panel and test the washer by running a short cycle to verify proper water level detection.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F02
Problem: Drain Pump Failure / Slow Drain

How to Fix Washer Error
1. Unplug the washer and turn off water supply valves.
2. Remove the lower front access panel by unscrewing the 3 screws at the bottom.
3. Place towels underneath to catch any residual water.
4. Locate the drain pump and disconnect the electrical connector.
5. Loosen the hose clamps on the drain hoses and remove them from the pump.
6. Remove the 3 mounting bolts securing the drain pump to the washer.
7. Inspect the old pump for debris, coins, or lint blocking the impeller.
8. Clean the pump housing thoroughly and check if the impeller spins freely by hand.
9. If the impeller is damaged or doesn’t spin, install the new pump.
10. Reconnect hoses with new clamps if needed, secure electrical connector, and test the drain function.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F01
Problem: Main Control Board (CCU) / EEPROM Error

How to Fix Washer Error
1. Unplug the washer from power for 10 minutes to reset the control board.
2. Remove the top panel by unscrewing the 3 screws at the back and sliding it forward.
3. Check all wire harness connections to the Central Control Unit (CCU) for loose or corroded connections.
4. Inspect the CCU board for any visible burn marks or damaged components.
5. If connections are good but error persists, disconnect the power cord and remove the CCU mounting screws.
6. Carefully disconnect all wire harnesses from the old CCU board.
7. Transfer any wire management clips to the new board.
8. Install the new CCU board and reconnect all harnesses in their correct positions.
9. Reassemble the top panel and plug in the washer to test.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Kenmore Dryer Error TC
Problem: Thermal cutoff open – safety device tripped

How to Fix Dryer Error
1. Turn off power supply immediately.
2. Allow dryer to cool completely.
3. Remove rear access panel.
4. Locate thermal cutoff device on heater housing or blower housing.
5. Disconnect electrical connector from thermal cutoff.
6. Test thermal cutoff continuity with multimeter (should read closed when cool).
7. If thermal cutoff is open, remove mounting screws and replace device.
8. Inspect high limit thermostat and temperature sensor for proper operation.
9. Check for airflow restrictions causing overheating.
10. Restore power and test heating cycle with temperature monitoring.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Kenmore Washer Error F0E2
Problem: Excessive suds detected – improper detergent usage

How to Fix Washer Error
1. Pause the wash cycle immediately.
2. Open washer door and remove as much water as possible.
3. Add 1 cup of white vinegar to help break down suds.
4. Run a drain/spin cycle without detergent.
5. If suds persist, repeat drain/spin cycle with cold water only.
6. Clean detergent dispenser thoroughly with warm water.
7. Use only HE (High Efficiency) detergent in future cycles.
8. Reduce detergent amount to manufacturer recommendations.
9. Check for detergent residue in dispenser housing.
10. Run a test cycle with proper HE detergent amount to verify operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Kenmore Washer Error F0E1
Problem: Door lock error during initial cycle start

How to Fix Washer Error
1. Turn off power supply.
2. Open washer door fully.
3. Inspect door lock mechanism for debris or physical damage.
4. Check door strike plate alignment with lock mechanism.
5. Test door lock solenoid resistance with multimeter.
6. Inspect wiring harness for damage or loose connections.
7. If lock assembly is faulty, disconnect electrical connector.
8. Remove mounting screws and replace door lock assembly.
9. Ensure proper alignment during installation.
10. Test door lock function during cycle start sequence.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026