Author: ApplianceFixGuide Team

How to Fix Kenmore Washer Error F6E2
Problem: Communication error between control boards

How to Fix Washer Error
1. Disconnect power at circuit breaker.
2. Remove control panel and main access covers.
3. Inspect all communication wire harnesses between boards.
4. Check for damaged, corroded, or loose connectors.
5. Test communication lines for continuity and proper voltage.
6. Clean all electrical contacts with contact cleaner.
7. If wiring is good, suspect control board failure.
8. Document all wire connections before disconnecting boards.
9. Replace faulty control board assembly.
10. Reconnect all harnesses and run diagnostic communication tests.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 4, 2026
How to Fix Maytag Washer Error F23
Problem: Heater Failure / Safety Thermostat Open

How to Fix Washer Error
1. Unplug the washer completely from power.
2. Remove the lower front access panel to access the pump area.
3. Place towels underneath to catch any residual water.
4. Locate the drain pump filter access cap.
5. Turn the filter cap counterclockwise to remove it (may require pliers for stubborn caps).
6. Pull out the filter screen and clean it thoroughly under running water.
7. Use a shop vac or towels to remove any remaining water from the pump housing.
8. Inspect the pump impeller for any debris or obstructions.
9. Clean the filter housing with an old toothbrush to remove any buildup.
10. Reinstall the clean filter screen and secure the cap tightly.
11. Reassemble the access panel and test the drain function.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 4, 2026
How to Fix Kenmore Washer Error F5E2
Problem: Door will not lock – mechanical or electrical failure

How to Fix Washer Error
1. Turn off power supply.
2. Open washer door fully.
3. Inspect door lock mechanism for debris or physical damage.
4. Check door strike plate alignment and condition.
5. Test door lock solenoid resistance with multimeter.
6. Inspect wiring harness for damage or corrosion.
7. Check door latch mechanism for proper engagement.
8. If lock assembly is faulty, disconnect electrical connector.
9. Remove mounting screws and replace door lock assembly.
10. Test door lock function multiple times to verify reliability.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 4, 2026
How to Fix Maytag Washer Error F22
Problem: Door Lock Mechanism Failure

How to Fix Washer Error
1. Unplug the washer from power source.
2. Check that the door is completely closed and latched.
3. Remove the lower front access panel to access the door lock mechanism.
4. Inspect the door strike plate for any damage or misalignment.
5. Disconnect the electrical connector from the door lock assembly.
6. Remove the mounting screws securing the door lock to the front panel.
7. Carefully remove the old door lock assembly and inspect for broken parts.
8. Install the new door lock assembly, ensuring proper alignment with the door strike.
9. Reconnect the electrical connector and secure mounting screws.
10. Test the door lock by closing the door and starting a cycle to verify it locks and unlocks properly.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 4, 2026
How to Fix Kenmore Washer Error F5E1
Problem: Lid switch error – lid open during cycle

How to Fix Washer Error
1. Turn off power supply.
2. Open washer lid fully.
3. Inspect lid switch mechanism for proper alignment.
4. Test lid switch continuity with multimeter (should change state when lid closes).
5. Check lid strike plate alignment with switch mechanism.
6. Inspect lid switch wiring for damage or loose connections.
7. If lid switch is faulty, disconnect electrical connector.
8. Remove mounting screws and replace lid switch assembly.
9. Ensure proper alignment during installation.
10. Test lid closure and switch operation during spin cycle.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 4, 2026
How to Fix Maytag Washer Error F20
Problem: Water Inlet Valve Failure / Insufficient Flow

How to Fix Washer Error
1. Check that both household water supply valves are fully open.
2. Inspect the water inlet hoses for kinks or damage that could restrict flow.
3. Remove the water inlet hoses from the back of the washer and clean the inlet screens.
4. Use an old toothbrush and vinegar to clean any mineral deposits from the screens.
5. If screens are clean but problem persists, unplug the washer.
6. Remove the top panel to access the water inlet valve assembly.
7. Disconnect electrical connectors from the inlet valves.
8. Remove the mounting screws and replace the entire water inlet valve assembly.
9. Reconnect all electrical connectors and water hoses.
10. Turn on water supply slowly and check for leaks before running a test cycle.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Kenmore Washer Error F3E2
Problem: Temperature sensor short circuit during operation

How to Fix Washer Error
1. Disconnect power at circuit breaker.
2. Remove lower front access panel.
3. Locate temperature sensor on tub or heater assembly.
4. Disconnect electrical connector from sensor.
5. Test sensor resistance with multimeter (should not read zero ohms).
6. Inspect sensor wiring for damage or pinching.
7. If sensor is shorted, remove mounting screw and replace sensor.
8. Check wiring harness for short circuits to ground.
9. Clean sensor mounting area and ensure proper sealing.
10. Reconnect electrical connector and test temperature readings during cycle.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F17
Problem: CCU / MCU Data Exchange Failure

How to Fix Washer Error
1. Unplug the washer from power outlet.
2. Turn off the hot water supply valve at the wall.
3. Remove the top panel by unscrewing the rear mounting screws.
4. Locate the hot water inlet valve solenoid on the water valve assembly.
5. Disconnect the electrical connector from the hot water solenoid.
6. Disconnect the hot water supply hose from the valve inlet.
7. Remove the mounting screws securing the water valve assembly.
8. Inspect the solenoid coil for visible damage or burned wires.
9. Install the new inlet valve assembly or replace just the solenoid if available separately.
10. Reconnect electrical connectors and water hoses.
11. Turn on water supply slowly and check for leaks before testing hot water fill function.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Kenmore Washer Error F0E4
Problem: High water temperature detected – safety shutdown

How to Fix Washer Error
1. Turn off power supply immediately.
2. Allow washer to cool for 30 minutes.
3. Check household water heater temperature settings (should not exceed 120°F).
4. Inspect temperature sensor for proper operation.
5. Test heating element for short circuits or grounding issues.
6. Check thermostat operation and calibration.
7. Verify proper water inlet valve mixing function.
8. Test temperature readings with external thermometer during fill cycle.
9. If temperature sensor is faulty, replace sensor assembly.
10. Run diagnostic cycle to verify proper temperature control.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026
How to Fix Maytag Washer Error F14
Problem: Main Control Board (CCU) EEPROM Error

How to Fix Washer Error
1. Unplug the washer completely from power.
2. Remove the dispenser drawer and the top panel to access the control console.
3. Remove the control panel mounting screws to access the user interface board.
4. Disconnect the ribbon cable connecting the user interface to the main control board.
5. Remove the mounting screws securing the user interface board to the console housing.
6. Carefully lift out the old user interface board and inspect for damaged buttons or display issues.
7. Transfer any overlays or button pads to the new board.
8. Install the new user interface board and secure with mounting screws.
9. Reconnect the ribbon cable ensuring it’s properly seated.
10. Reassemble the control panel and test all buttons and display functions before replacing the top panel.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 3, 2026