Author: ApplianceFixGuide Team

  • How to Fix LG Washer Error SE

    How to Fix LG Washer Error SE

    Problem: Sensor error – motor sensor (hall sensor) malfunction

    How to Fix SE Error

    1. Disconnect the washer from power. This error points to a faulty motor Hall Sensor.
    2. You will need to access the motor at the back or bottom of the washer. Remove the rear service panel.
    3. Remove the large central bolt holding the rotor to the drive shaft. Pull the rotor off.
    4. The stator (the part with copper windings) is now exposed. The Hall Sensor is a small component mounted on it. Disconnect the wire harnesses.
    5. Unbolt the stator, and replace the Hall Sensor (or the entire stator assembly).
    6. Reassemble in reverse order.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error dE

    How to Fix LG Washer Error dE

    Problem: Door lock error – washer door/lid was unable to lock

    How to Fix dE Error

    1. First, ensure the door is closed completely and nothing is caught in it. Press firmly on the door to engage the latch.
    2. If the error persists, unplug the washer. The door lock/latch assembly has likely failed.
    3. For front-load washers, you’ll need to remove the top panel, then peel back the door boot gasket clamp to access the lock assembly from inside the cabinet.
    4. Disconnect the wire harness from the lock.
    5. Remove the screws holding the lock assembly in place and replace it with the new one.
    6. Reassemble everything in reverse order.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error dE1

    How to Fix LG Washer Error dE1

    Problem: Door not closed properly – laundry may be caught between door and rubber gasket

    How to Fix dE1 Error

    1. This is a variant of the ‘dE’ error. First, check carefully that no clothing is caught between the door and the rubber gasket, preventing a tight seal.
    2. Open and close the door firmly. Listen for a solid ‘click’ from the latch.
    3. If the error persists, the door lock assembly is faulty. Unplug the washer and follow the replacement procedure for the ‘dE’ error code.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error dE3

    How to Fix LG Washer Error dE3

    Problem: Door/lid not properly latched – primarily for SideKick pedestal washer

    How to Fix dE3 Error

    1. This error is specific to the LG SideKick pedestal washer. Unplug the pedestal washer from its power source.
    2. Ensure the small pedestal drawer is closed completely and nothing is obstructing it.
    3. If the error continues, the door lock for the pedestal has failed.
    4. You will need to pull the pedestal out, access the lock mechanism from the top or side, and replace the assembly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error dHE

    How to Fix LG Washer Error dHE

    Problem: Dry function error (temporary) – issue with heater in washer/dryer combo during drying cycle

    How to Fix dHE Error

    1. This indicates a temporary error with the drying system in a washer/dryer combo, often due to a sensor detecting unusual conditions.
    2. Press the Start/Pause button to pause the cycle, then press it again to resume. This often clears the error.
    3. If the error returns, turn the washer off, wait 5 minutes, and then restart the dry cycle.
    4. Ensure the lint filter is clean, as poor airflow can contribute to drying errors.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error tCL

    How to Fix LG Washer Error tCL

    Problem: Tub Clean reminder – time to run tub clean cycle; appears every 30 cycles

    How to Fix tCL Error

    1. This is a reminder to clean the washer tub. It is not an error.
    2. Ensure the washer is empty.
    3. Add a washing machine cleaning tablet or liquid bleach to the dispenser (do not mix).
    4. Close the door, select the ‘Tub Clean’ cycle, and press Start.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error tE

    How to Fix LG Washer Error tE

    Problem: Heating/temperature error – usually caused by faulty thermistor (temperature sensor)

    How to Fix tE Error

    1. Unplug the washer. This error indicates a heating or temperature sensing problem.
    2. The most common cause is a faulty thermistor (temperature sensor). It’s usually located on or near the heating element assembly at the bottom of the tub.
    3. Access the thermistor, disconnect its wiring, and test its resistance with a multimeter. A reading of infinity or zero ohms indicates it has failed.
    4. Replace the thermistor, ensuring a snug fit.
    5. Reassemble the washer and restore power.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error u5

    How to Fix LG Washer Error u5

    Problem: Vibration sensor error – display variant of vS

    How to Fix u5 Error

    1. This is a display variant of the ‘vS’ vibration sensor error. Unplug the washer.
    2. Remove the necessary panel (usually front or back) to access the outer tub.
    3. Locate the vibration sensor mounted on the tub.
    4. Check its wire harness for a secure connection. If the connection is good, the sensor is faulty.
    5. Replace the sensor and reassemble the washer.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error uS

    How to Fix LG Washer Error uS

    Problem: Vibration sensor error – display variant of vS

    How to Fix uS Error

    1. This is another display variant of the ‘vS’ vibration sensor error. Unplug the washer.
    2. Follow the same procedure as for the ‘vS’ error: access the outer tub, check the sensor’s wiring, and replace the sensor if the wiring is secure.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Washer Error vS

    How to Fix LG Washer Error vS

    Problem: Vibration sensor error – contact issue with vibration sensor or sensor malfunction

    How to Fix vS Error

    1. Unplug the washer from the power outlet.
    2. The vibration sensor is typically mounted on the side of the outer tub. You will need to remove the front or rear panel to access it.
    3. Check the wire harness connection to the sensor. Unplug it and plug it back in to ensure it’s secure.
    4. If the connection is good, the sensor itself has likely failed.
    5. Unbolt the old sensor, install the new one, and reconnect the wiring.
    6. Reassemble the panel and run a calibration cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Lg error codes: Lg Error Codes