Category: Speed Queen

  • How to Fix Speed Queen Washer Error Ei0E

    How to Fix Speed Queen Washer Error Ei0E

    Error Code: Ei0E Difficulty: Moderate

    Problem: IR encryption error.

    How to Fix Ei0E Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei0E and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei0C

    How to Fix Speed Queen Washer Error Ei0C

    Error Code: Ei0C Difficulty: Moderate

    Problem: IR timeout exceeded.

    How to Fix Ei0C Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei0C and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei0A

    How to Fix Speed Queen Washer Error Ei0A

    Error Code: Ei0A Difficulty: Moderate

    Problem: IR framing error.

    How to Fix Ei0A Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei0A and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei09

    How to Fix Speed Queen Washer Error Ei09

    Error Code: Ei09 Difficulty: Moderate

    Problem: IR CRC-16 error.

    How to Fix Ei09 Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei09 and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei05

    How to Fix Speed Queen Washer Error Ei05

    Error Code: Ei05 Difficulty: Moderate

    Problem: IR data invalid or out of range.

    How to Fix Ei05 Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei05 and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Washer door lock assembly
      Common replacement category: Door/lid lock
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: High
      Door and lid lock errors usually require checking the lock/latch assembly and matching it by full model number.

      Search Amazon for Washer door lock assembly

    • Washer door strike
      Common replacement category: Door strike / latch
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      A worn strike or latch can keep the lock from reporting closed.

      Search Amazon for Washer door strike

    • Washer lid switch
      Common replacement category: Lid switch
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Top-load lid errors can be caused by a failed lid switch or lock circuit.

      Search Amazon for Washer lid switch

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei04

    How to Fix Speed Queen Washer Error Ei04

    Error Code: Ei04 Difficulty: Moderate

    Problem: IR upload request expected.

    How to Fix Ei04 Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei04 and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei03

    How to Fix Speed Queen Washer Error Ei03

    Error Code: Ei03 Difficulty: Moderate

    Problem: Invalid IR command.

    How to Fix Ei03 Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei03 and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Washer door lock assembly
      Common replacement category: Door/lid lock
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: High
      Door and lid lock errors usually require checking the lock/latch assembly and matching it by full model number.

      Search Amazon for Washer door lock assembly

    • Washer door strike
      Common replacement category: Door strike / latch
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      A worn strike or latch can keep the lock from reporting closed.

      Search Amazon for Washer door strike

    • Washer lid switch
      Common replacement category: Lid switch
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Top-load lid errors can be caused by a failed lid switch or lock circuit.

      Search Amazon for Washer lid switch

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei02

    How to Fix Speed Queen Washer Error Ei02

    Error Code: Ei02 Difficulty: Moderate

    Problem: IR communication timeout.

    How to Fix Ei02 Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei02 and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error Ei01

    How to Fix Speed Queen Washer Error Ei01

    Error Code: Ei01 Difficulty: Moderate

    Problem: IR communication transmission failure.

    How to Fix Ei01 Error (Step-by-Step)

    1. Confirm the display is showing exactly Ei01 and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Speed Queen washer IR communication board
      Common replacement category: IR communication board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      IR communication errors can involve the communication board or control interface.

      Search Amazon for Speed Queen washer IR communication board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Timeout and framing errors can be caused by wiring or connector issues.

      Search Amazon for Washer communication harness

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control-board matching must be confirmed by full model number.

      Search Amazon for Commercial washer control board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Speed Queen Washer Error oUt oF ordEr

    How to Fix Speed Queen Washer Error oUt oF ordEr

    Error Code: oUt oF ordEr Difficulty: Moderate

    Problem: Fatal-error banner on commercial controls.

    How to Fix oUt oF ordEr Error (Step-by-Step)

    1. Confirm the display is showing exactly oUt oF ordEr and not a similar-looking code.
    2. Turn the washer off and disconnect power before opening panels or checking wiring.
    3. Check the simple causes first: load balance, hoses, water supply, drain path, and door or lid closure.
    4. Use the full model number from the washer tag before ordering any replacement part.
    5. Restore power and run a short test cycle after the basic checks are complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Speed Queen Washer

    Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, water supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.
    5. Use the complete Speed Queen washer model number before ordering parts, because the same code can use different assemblies across platforms.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Speed Queen model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Likely Parts to Check

    No exact official OEM part number is listed here because the correct Speed Queen Washer part can vary by full model number. These are targeted part-category searches, not universal fit claims.

    • Commercial washer control board
      Common replacement category: Machine control board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Control and communication errors may require model-specific board diagnosis.

      Search Amazon for Commercial washer control board

    • Washer communication harness
      Common replacement category: Communication harness
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Loose or damaged harnesses can cause board-to-board communication faults.

      Search Amazon for Washer communication harness

    • Washer output board
      Common replacement category: Output/drive board
      Fit note: Exact OEM part number varies by model. Confirm compatibility using the full model number before buying.
      Confidence: Medium
      Some Speed Queen controls use a separate output or drive board that must be matched by model.

      Search Amazon for Washer output board

    Before ordering: match the part to the complete model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.