Category: Samsung

  • How to Fix Samsung Washer Error 14C2

    How to Fix Samsung Washer Error 14C2

    Problem: Hot/cold water supply hoses reversed (FlexWash)

    How to Fix 14C2 Error

    1. This code indicates the hot and cold water supply hoses for the upper FlexWash unit are reversed.
    2. Shut off the water supply faucets behind the washer.
    3. Disconnect the two water hoses from the back of the washer. The hose from the hot water faucet should connect to the ‘H’ or ‘HOT’ inlet port, and the hose from the cold water faucet should connect to the ‘C’ or ‘COLD’ inlet port.
    4. Swap the hoses to their correct positions, tighten them securely, and turn the water faucets back on completely.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 19C1

    How to Fix Samsung Washer Error 19C1

    Problem: Voltage error (FlexWash)

    How to Fix 19C1 Error

    1. This error indicates the washer has detected an issue with the incoming voltage supply to the FlexWash upper unit.
    2. Ensure the washer is plugged into a dedicated, properly grounded outlet. Do not use an extension cord.
    3. Try unplugging the washer for 5-10 minutes to reset the control board.
    4. If the problem persists, you may have an issue with your home’s electrical supply. Consider having an electrician check the voltage at the outlet.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 1C

    How to Fix Samsung Washer Error 1C

    Problem: Water level sensor error or leak detected

    How to Fix 1C Error

    1. UNPLUG THE WASHER. This code indicates a water level sensor error or, less commonly, a leak.
    2. First, check for any signs of a water leak under the machine. If a leak is found, the leak sensor has been tripped and the source of the leak must be found and repaired.
    3. If there is no leak, the water level sensor (pressure switch) has likely failed. It is usually located near the top of the tub, accessible by removing the top panel of the washer. It has a thin air tube connected to it.
    4. Disconnect the wire harness and the air tube from the old sensor. Check the tube for blockages or kinks. Remove the old sensor and install the new one.
    5. Securely reattach the air tube and wire harness, then reassemble the washer.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 1U6

    How to Fix Samsung Washer Error 1U6

    Problem: Unbalanced load (FlexWash)

    How to Fix 1U6 Error

    1. This is an ‘Unbalanced load’ error for the upper FlexWash unit. First, pause the cycle and manually redistribute the small load evenly in the top basket.
    2. If the error happens on every cycle regardless of load, the suspension system has failed.
    3. Replacing the suspension on the small upper washer is a complex job requiring significant disassembly of the unit’s top section.
    4. Due to the complexity, this repair is best left to a professional technician.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 1dC4

    How to Fix Samsung Washer Error 1dC4

    Problem: FlexWash upper latch rubber button missing

    How to Fix 1dC4 Error

    1. This error indicates the small rubber bumper or button for the upper FlexWash latch is missing or damaged, preventing the latch from registering as closed.
    2. Open the top lid and inspect the latching mechanism. Look for a small rubber piece that makes contact when the lid closes.
    3. If this rubber bumper is missing, it needs to be replaced. It typically just pushes into place.
    4. Press the new rubber latch bumper firmly into its designated hole on the latch assembly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 2E

    How to Fix Samsung Washer Error 2E

    Problem: Voltage / power supply error

    How to Fix 2E Error

    1. UNPLUG THE WASHER. This is a critical internal error related to the main control board.
    2. First, try a hard reset by leaving the washer unplugged for 10 minutes.
    3. If the error returns, the main control board is defective and must be replaced.
    4. This is a complex job that involves accessing the main electronics, carefully labeling and disconnecting numerous wire harnesses, and swapping the board. Professional service is recommended.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 3C3

    How to Fix Samsung Washer Error 3C3

    Problem: Motor error (alias for 3E3)

    How to Fix 3C3 Error

    1. UNPLUG THE WASHER. This is a critical motor error, often related to a bad main control board.
    2. While it’s a motor error, the cause is often the control board failing to properly communicate with or power the motor.
    3. A hard reset (unplugging for 10 minutes) is worth trying but unlikely to solve the issue.
    4. The most common repair for this specific code is to replace the main control board.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 3C4

    How to Fix Samsung Washer Error 3C4

    Problem: Motor error (alias for 3E4)

    How to Fix 3C4 Error

    1. UNPLUG THE WASHER. This complex error can be caused by a motor issue or excessive vibration from failed suspension fooling the motor control.
    2. First, check for a mechanical issue. Try to move the tub up and down. If it bounces more than once or feels loose, the suspension rods are bad and must be replaced (see code 1Ub or Ub).
    3. If the suspension feels firm, the issue is likely with the motor stator. This requires removing the rear panel and the motor rotor to access and replace the stator.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 4C2

    How to Fix Samsung Washer Error 4C2

    Problem: Hot/cold water supply hoses reversed

    How to Fix 4C2 Error

    1. This code indicates the hot and cold water supply hoses for the main washer are reversed.
    2. Shut off the water supply faucets behind the washer.
    3. Disconnect the two water hoses from the back of the washer. The hose from the hot water faucet should connect to the ‘H’ or ‘HOT’ inlet port, and the hose from the cold water faucet should connect to the ‘C’ or ‘COLD’ inlet port.
    4. Swap the hoses to their correct positions, tighten them securely, and turn the water faucets back on completely.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Washer Error 5DC

    How to Fix Samsung Washer Error 5DC

    Problem: Detergent drawer not fully closed

    How to Fix 5DC Error

    1. This is an alias for the ‘SDC’ code. It means the detergent drawer was not fully closed when a cycle was started.
    2. Push the detergent drawer in completely until it clicks into place.
    3. The cycle should then resume or be ready to start.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Samsung error codes: Samsung Error Codes