Category: Washer

Problem: Electrical power interruption during cycle

How to Fix Washer Error

1. Check household circuit breaker for tripped condition.
2. Verify power outlet is functioning with another appliance.
3. Inspect power cord for damage or loose connections.
4. Check washer poer cord connection at terminal block inside machine.
5. Test voltage at terminal block with multimeter (should read 120V).
6. If power was restored, press START/PAUSE button to resume cycle.
7. If cycle won’t restart, disconnect power for 5 minutes to reset control boards.
8. Check for blown fuses on control boards if accessible.
9. Inspect main power supply wiring for damage or corrosion.
10. Test washer operation after power restoration and reset procedures.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Load imbalance detected during spin cycle

How to Fix Washer Error

1. Pause the wash cycle immediately.
2. Open washer door/lid and redistribute laundry evenly around drum.
3. Remove any large, heavy items that may cause imbalance.
4. Add a few smaller items to help balance the load if needed.
5. Close door/lid and restart the spin cycle.
6. If imbalance persists, reduce spin speed setting for this load.
7. Check washer leveling by adjusting feet until bubble level shows level.
8. Ensure all four feet are firmly on floor and not rocking.
9. For future loads, distribute items of similar weight evenly around drum.
10. Test with balanced load to verify proper spin operation.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Motor speed control failure – unable to reach proper RPM

How to Fix Washer Error

1. Turn off power at circuit breaker.
2. Remove front access panel.
3. Inspect drive motor for overheating or unusual smells.
4. Check motor wiring harness for damage or loose connections.
5. Test motor windings for proper resistance readings.
6. Inspect motor speed sensor and connections.
7. Check drive belt for wear, tension, or damage (if applicable).
8. If motor control is faulty, replace motor control board assembly.
9. Verify proper mechanical alignment of all drive components.
10. Test motor operation at various speeds to verify proper function.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Temperature sensor failure – incorrect readings

How to Fix Washer Error

1. Disconnect power at circuit breaker.
2. Remove lower front access panel.
3. Locate temperature sensor on tub or heater assembly.
4. Disconnect electrical connector from sensor.
5. Test sensor resistance with multimeter at room temperature.
6. Compare readings to manufacturer specifications chart.
7. If sensor is out of range, remove mounting screw and replace sensor.
8. Check wiring harness for damage or corrosion.
9. Clean sensor mounting area and ensure proper sealing.
10. Reconnect electrical connector and test temperature readings during cycle.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Drain pump failure – water not draining properly

How to Fix Washer Error

1. Turn off power supply.
2. Remove lower front access panel.
3. Check drain hose for kinks, blockages, or improper routing.
4. Remove drain pump access cover and clean debris from filter.
5. Inspect drain pump impeller for damage or obstructions.
6. Test drain pump motor resistance with multimeter.
7. Check drain pump wiring for corrosion or damage.
8. If pump is weak or clogged, disconnect electrical connector and hoses.
9. Remove mounting screws and replace drain pump assembly.
10. Test drain cycle timing and verify complete drainage.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Water inlet valve failure – no water entering

How to Fix Washer Error

1. Turn off power and check household water supply valves.
2. Verify water pressure at supply lines (minimum 20 PSI required).
3. Remove lower front access panel.
4. Inspect water inlet valve screens for debris or mineral buildup.
5. Clean inlet valve filter screens with vinegar solution.
6. Test inlet valve solenoids with multimeter for proper resistance.
7. If valve is faulty, disconnect water supply lines and electrical connector.
8. Remove mounting screws and replace water inlet valve assembly.
9. Restore water and power connections.
10. Test fill cycle operation and timing.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Unknown

How to Fix Washer Error

Consult manual.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Drainage timeout – long drain detected

How to Fix Washer Error

1. Turn off power supply.
2. Remove lower front access panel.
3. Check drain hose for kinks, blockages, or improper routing.
4. Remove drain pump access cover and clean filter debris.
5. Inspect drain pump impeller for damage or obstructions.
6. Test drain pump motor resistance with multimeter.
7. Check drain pump wiring for corrosion or damage.
8. If pump is weak or clogged, replace drain pump assembly.
9. Ensure drain hose has proper high loop installation.
10. Test drain cycle timing and verify complete drainage.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Water overflow detected – pressure switch or valve failure

How to Fix Washer Error

1. Turn off power and water supply immediately.
2. Remove standing water from washer bottom with towels or wet vacuum.
3. Check pressure switch tube for kinks, cracks, or disconnections.
4. Inspect water level pressure switch for proper operation.
5. Test pressure switch contacts with multimeter while blowing into tube.
6. Check inlet valve operation for proper shut-off function.
7. Inspect drain system for blockages preventing proper drainage.
8. If pressure switch is faulty, replace pressure switch assembly.
9. Clean pressure switch tube and connections thoroughly.
10. Test fill cycle with manual monitoring to verify proper water level control.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Excessive suds detected during cycle

How to Fix Washer Error

1. Pause the wash cycle immediately.
2. Open washer door/lid and remove standing water with towels.
3. Add 1 cup of white vinegar to help dissipate suds.
4. Run a drain/spin cycle without adding any detergent.
5. If suds remain, repeat drain/spin cycle with cold water only.
6. Thoroughly clean detergent dispenser and housing.
7. Switch to HE (High Efficiency) detergent exclusively.
8. Use half the recommended detergent amount for future loads.
9. Check for detergent buildup in dispenser housing and clean.
10. Run a test cycle with proper HE detergent amount to verify operation.

Browse all Kenmore error codes: Kenmore Error Codes