Category: Kenmore

  • How to Fix Kenmore Refrigerator Error F27

    How to Fix Kenmore Refrigerator Error F27

    Problem: Water filter bypass valve fault or improper filter installation

    How to Fix Refrigerator Error

    1. Remove current water filter cartridge.
    2. Inspect filter head for debris or damaged O-rings.
    3. Install new genuine filter cartridge, rotating clockwise until it stops (typically 90-180 degrees).
    4. Listen for distinct ‘click’ indicating proper seating.
    5. If error persists, locate filter bypass valve (internal to filter head).
    6. Remove filter head assembly (requires disconnecting water lines – have towels ready).
    7. Inspect bypass valve mechanism for broken spring or jammed plunger.
    8. Replace entire filter head assembly if bypass valve faulty.
    9. Reset filter status indicator after repair.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error F28

    How to Fix Kenmore Refrigerator Error F28

    Problem: Compressor winding temperature sensor fault

    How to Fix Refrigerator Error

    1. UNPLUG unit.
    2. Remove rear lower access panel to access compressor.
    3. Locate temperature sensor clipped to compressor shell (small probe with 2 wires, often under tape).
    4. Carefully peel back tape/clamp to access sensor connector.
    5. Disconnect and test resistance (should read 5k-15k ohms at room temp).
    6. Replace sensor if open/shorted.
    7. Reattach new sensor to compressor shell in same location using high-temp adhesive or metal strap – MUST maintain good thermal contact.
    8. If sensor good but error persists, suspect failing compressor windings causing actual overtemperature condition – requires professional diagnosis.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error F29

    How to Fix Kenmore Refrigerator Error F29

    Problem: Ice crusher solenoid failure preventing blade engagement

    How to Fix Refrigerator Error

    1. UNPLUG refrigerator.
    2. Remove ice bin and locate crusher solenoid (mounted near auger drive mechanism in freezer door or rear wall).
    3. Disconnect wiring harness and test solenoid coil for continuity (should read 100-300 ohms).
    4. Manually operate solenoid plunger – should move freely between cubed/crushed positions.
    5. Check for ice jams around crusher mechanism – defrost completely if frozen.
    6. Replace solenoid assembly if electrically open or mechanically seized.
    7. Verify proper alignment with crusher blade actuator after installation.
    8. Test both cubed and crushed ice functions – should hear distinct solenoid ‘clunk’ when switching modes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error F30

    How to Fix Kenmore Refrigerator Error F30

    Problem: Power supply voltage fault detected by main control board

    How to Fix Refrigerator Error

    1. Verify household voltage at outlet (should read 110-125V AC).
    2. Check circuit breaker for partial trip or loose connection.
    3. Inspect power cord for damage – replace if frayed/burnt.
    4. Remove rear access panel and locate main control board.
    5. Test AC voltage at board input terminals (should match outlet voltage).
    6. If input voltage good but error persists, suspect failed voltage monitoring circuit on main board.
    7. Replace main control board assembly.
    8. After replacement, monitor for 24 hours to verify stable operation without error recurrence.
    9. If error returns, investigate household wiring issues or install dedicated circuit.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error 1 BLINK

    How to Fix Kenmore Refrigerator Error 1 BLINK

    Problem: Refrigerator temperature sensor failure (111 series flash code)

    How to Fix Refrigerator Error

    1. UNPLUG unit.
    2. Remove main control board cover (located in fresh food compartment ceiling or rear wall).
    3. Observe green LED – counts flashes then pauses (1 flash = fridge sensor fault).
    4. Locate refrigerator thermistor per model diagram (typically behind rear wall panel).
    5. Disconnect connector and test resistance.
    6. Replace sensor if open/shorted.
    7. Reposition sensor in identical location.
    8. Restore power and verify LED stops flashing error sequence within 5 minutes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error 2 BLINK

    How to Fix Kenmore Refrigerator Error 2 BLINK

    Problem: Freezer temperature sensor failure (111 series flash code)

    How to Fix Refrigerator Error

    1. UNPLUG refrigerator.
    2. Remove main control board cover to observe LED flash pattern (2 flashes = freezer sensor fault).
    3. Remove evaporator cover panel in freezer compartment.
    4. Locate freezer thermistor clipped to evaporator coil.
    5. Disconnect and test resistance.
    6. Replace if faulty.
    7. Position new sensor EXACTLY as original – critical for defrost cycle timing.
    8. Restore power and verify error clears within 5 minutes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error 3 BLINK

    How to Fix Kenmore Refrigerator Error 3 BLINK

    Problem: Defrost heater circuit failure (111 series flash code)

    How to Fix Refrigerator Error

    1. UNPLUG unit and defrost completely.
    2. Remove evaporator cover panel in freezer.
    3. Observe control board LED – 3 flashes indicates defrost system fault.
    4. Test defrost heater for continuity (should read 20-50 ohms).
    5. Test defrost thermostat when cold (should read closed).
    6. Replace faulty component(s).
    7. Inspect wiring for burnt sections near heater connections.
    8. After repair, initiate manual defrost cycle to verify heater activates and melts frost within 20 minutes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error SY CF

    How to Fix Kenmore Refrigerator Error SY CF

    Problem: Communication failure between main control and user interface boards (253 series)

    How to Fix Refrigerator Error

    1. UNPLUG unit for 5 minutes to reset electronics.
    2. Restore power and check if error clears temporarily.
    3. Remove rear access panel to locate main control board.
    4. Inspect all wire harness connections – unplug/replug each connector firmly.
    5. Check for corrosion on connectors – clean with electrical contact cleaner.
    6. Test continuity of communication wires between boards (typically 4-6 conductor ribbon cable).
    7. If wiring intact but error persists, replace main control board first (more common failure).
    8. If error remains after main board replacement, replace display/user interface board.
    9. After repairs, allow 24 hours for system calibration before evaluating performance.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error OF

    How to Fix Kenmore Refrigerator Error OF

    Problem: Open freezer thermistor circuit (253 series upright freezer code)

    How to Fix Refrigerator Error

    1. UNPLUG freezer.
    2. Remove interior panel to access evaporator and thermistor.
    3. Locate freezer temperature sensor clipped to evaporator coil.
    4. Disconnect connector and test resistance (should read 5k-15k ohms).
    5. If reading OL (open circuit), replace thermistor.
    6. Ensure new sensor makes full contact with evaporator tubing.
    7. Secure with original clip or high-temp adhesive.
    8. Restore power and verify temperature display returns to normal within 10 minutes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error PF

    How to Fix Kenmore Refrigerator Error PF

    Problem: Power failure detected – unit lost AC power temporarily

    How to Fix Refrigerator Error

    1. Verify household power restored to outlet.
    2. Check circuit breaker hasn’t tripped.
    3. Press any control panel button to acknowledge power restoration.
    4. Display will show ‘PF’ for 5 seconds then return to normal operation.
    5. No parts replacement needed – this is informational code only.
    6. If temperatures rose significantly during outage, allow 4-6 hours for unit to re-stabilize before adding new food items.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.