Category: Kenmore

  • How to Fix Kenmore Dishwasher Error F7E2

    How to Fix Kenmore Dishwasher Error F7E2

    Problem: Heating element won’t shut off; relay stuck on control board

    How to Fix F7E2 Error

    1. This is a dangerous fault. Immediately shut off power to the dishwasher at the circuit breaker to prevent the heating element from overheating.
    2. The issue is a stuck relay on the electronic control board, which means the board is continuously sending power to the heater.
    3. Access the main control board, typically behind the console or at the base of the dishwasher.
    4. Carefully label and disconnect all wire harnesses from the old board.
    5. Install the new control board, ensuring all connections are secure.
    6. Reassemble the dishwasher and restore power.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F8E4

    How to Fix Kenmore Dishwasher Error F8E4

    Problem: Drain pump problem (variant)

    How to Fix F8E4 Error

    1. This is a variant of the drain pump error code 8-
    2. Disconnect power to the dishwasher.
    3. Remove the lower access panel to get to the drain pump.
    4. Check for any blockages in the drain hose and the pump inlet.
    5. If there are no blockages, check the wire harness connection to the pump.
    6. If wiring is good, the drain pump is likely defective and needs to be replaced.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error Sanitized LED Blinks at End of Cycle

    How to Fix Kenmore Dishwasher Error Sanitized LED Blinks at End of Cycle

    Problem: Sanitation not achieved; water did not reach required temperature

    How to Fix Sanitized LED Blinks at End of Cycle Error

    1. This indicates the water did not reach the high temperature required for sanitization. This is often due to the hot water supply to the dishwasher not being hot enough.
    2. Before starting the dishwasher, run the hot water at the kitchen sink until it is fully hot.
    3. Ensure your home’s water heater is set to at least 120°F (49°C).
    4. Avoid running other hot water appliances (like showers or washing machines) at the same time as the dishwasher.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error Er IS

    How to Fix Kenmore Refrigerator Error Er IS

    Problem: Ice level sensor/optic eye failure in freezer door detecting ice bin full condition

    How to Fix Refrigerator Error

    1. UNPLUG refrigerator.
    2. Open freezer door and locate emitter/receiver sensors on opposite walls of ice chute (small red lenses).
    3. Clean lenses thoroughly with soft cloth and isopropyl alcohol.
    4. Check alignment – sensors must face each other directly without obstruction.
    5. Disconnect wiring harnesses and test continuity through sensor circuit.
    6. If sensors clean/aligned but error persists, replace both emitter and receiver assemblies (must replace as pair).
    7. Verify operation by placing hand between sensors – ice maker should stop when beam interrupted.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error 5Y EF

    How to Fix Kenmore Refrigerator Error 5Y EF

    Problem: Temperature sensor fault causing evaporator fan circuit error (253 series variant)

    How to Fix Refrigerator Error

    1. UNPLUG refrigerator.
    2. Test BOTH freezer and refrigerator thermistors for proper resistance values (consult tech sheet for model-specific values).
    3. If either sensor out of spec, replace faulty thermistor.
    4. If sensors good, proceed to evaporator fan motor testing per SY EF procedure.
    5. Check voltage at fan motor connector when door closed (should read 12-14V DC).
    6. If voltage present but fan not running, replace fan motor.
    7. If no voltage, suspect main control board failure – replace board after confirming all sensors/fans test good.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error F1

    How to Fix Kenmore Refrigerator Error F1

    Problem: Refrigerator compartment thermistor open circuit or out-of-range reading

    How to Fix Refrigerator Error

    1. UNPLUG refrigerator.
    2. Locate fresh food thermistor – typically behind rear wall panel near top air vent or in light assembly housing.
    3. Remove access panel and disconnect sensor connector.
    4. Measure resistance at room temperature (should be 5k-15k ohms depending on model).
    5. If reading OL (open) or wildly out of spec, replace thermistor.
    6. Route new sensor wire carefully avoiding door hinge pinch points.
    7. Secure sensor in original clip/location.
    8. Restore power and allow 4-6 hours for temperature stabilization before evaluating performance.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error F2

    How to Fix Kenmore Refrigerator Error F2

    Problem: Freezer compartment thermistor failure

    How to Fix Refrigerator Error

    1. UNPLUG unit.
    2. Remove evaporator cover panel inside freezer compartment.
    3. Locate freezer thermistor clipped to evaporator coil tubing (white probe with 2 wires).
    4. Disconnect connector and test resistance (5k-15k ohms at room temp).
    5. Replace if open/shorted or reading outside specification.
    6. IMPORTANT: Position new sensor in EXACT same location as original – even 1 inch difference causes temperature control issues.
    7. Secure with original clip or high-temp adhesive.
    8. Reassemble and verify freezer reaches 0°F within 4 hours of startup.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error F3

    How to Fix Kenmore Refrigerator Error F3

    Problem: Defrost system failure – heater or thermostat fault causing excessive frost buildup

    How to Fix Refrigerator Error

    1. UNPLUG refrigerator and initiate manual defrost (leave doors open 8-12 hours until all ice melts).
    2. Remove evaporator cover panel in freezer.
    3. Test defrost heater for continuity (should read 20-50 ohms).
    4. Test defrost thermostat when cold/frozen (should read closed/<1 ohm).
    5. Replace faulty component(s).
    6. Inspect wiring for burnt sections near heater connections.
    7. After repair, monitor for 3 defrost cycles (typically every 8-10 hours) to verify heater activates and melts frost completely each cycle.
    8. If frost returns within 48 hours, suspect adaptive defrost control board failure.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error F4

    How to Fix Kenmore Refrigerator Error F4

    Problem: Evaporator fan motor failure in fresh food compartment (dual evaporator models)

    How to Fix Refrigerator Error

    1. UNPLUG unit.
    2. Locate fresh food evaporator fan – typically behind rear wall panel in refrigerator section (not freezer).
    3. Remove access panel (4-6 screws).
    4. Disconnect wiring harness and test motor windings.
    5. Manually spin fan blade – check for ice obstruction or bearing failure.
    6. Replace motor assembly if faulty.
    7. Ensure fan blade orientation matches original (critical for proper airflow direction through diffuser).
    8. Verify operation by listening for continuous fan operation when doors closed – should hear gentle airflow from rear vents.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Refrigerator Error F5

    How to Fix Kenmore Refrigerator Error F5

    Problem: Water inlet valve failure preventing water flow to ice maker/dispenser

    How to Fix Refrigerator Error

    1. SHUT OFF water supply valve and UNPLUG refrigerator.
    2. Remove rear lower access panel.
    3. Locate water inlet valve (solenoid assembly with 1/4″ water line input and 2 outputs).
    4. Disconnect electrical connectors and water lines (have towels ready).
    5. Remove mounting screws and extract valve assembly.
    6. Test solenoid coils for continuity (should read 300-500 ohms each).
    7. Replace entire valve assembly if either coil open or leaking.
    8. Reconnect water lines hand-tight plus 1/4 turn, open supply valve slowly, check for leaks before restoring power.
    9. Test dispenser and ice maker operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes