Category: Kenmore

  • How to Fix Kenmore Dryer Error F06

    How to Fix Kenmore Dryer Error F06

    Problem: Thermistor communication failure with control board

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Inspect thermistor wiring harness for damage or pinched wires.
    4. Check connector at control board for corrosion or loose connections.
    5. Test sensor resistance and compare to expected values.
    6. Clean electrical contacts with contact cleaner.
    7. If sensor tests good but error persists, suspect control board failure.
    8. Replace thermistor assembly as first step.
    9. If error continues, replace main control board.
    10. Test heating cycle operation and temperature monitoring.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F32

    How to Fix Kenmore Dishwasher Error F32

    Problem: Open circuit detected in control system

    How to Fix Dishwasher Error

    1. Check all wiring connections and reseat connectors.
    2. Test continuity of all control circuit wires.
    3. Inspect control board traces for opens or cracks.
    4. Test relay contacts and switches for proper operation.
    5. Verify sensor and actuator connections.
    6. Replace control board if open circuit cannot be located.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F33

    How to Fix Kenmore Dishwasher Error F33

    Problem: EEPROM memory failure on control board

    How to Fix Dishwasher Error

    1. Attempt master reset by disconnecting power for 1 hour.
    2. Check control board backup battery if equipped.
    3. Inspect EEPROM chip pins for corrosion or poor solder joints.
    4. Test EEPROM data lines for proper communication.
    5. Replace control board assembly as EEPROM is typically not field-replaceable.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F05

    How to Fix Kenmore Dryer Error F05

    Problem: Thermistor calibration error – sensor out of range

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Locate thermistor sensor on heating assembly.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is out of calibration range, remove mounting screws.
    8. Install new thermistor assembly with proper alignment.
    9. Reconnect electrical connector and verify proper seating.
    10. Run diagnostic cycle to clear error and verify temperature readings.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F34

    How to Fix Kenmore Dishwasher Error F34

    Problem: RAM memory failure on control board

    How to Fix Dishwasher Error

    1. Power cycle dishwasher multiple times to clear temporary faults.
    2. Check control board voltage supply stability.
    3. Inspect RAM chip and surrounding components for damage.
    4. Test data bus signals to RAM chip.
    5. Replace control board as RAM failure requires board replacement.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F35

    How to Fix Kenmore Dishwasher Error F35

    Problem: Communication timeout between system components

    How to Fix Dishwasher Error

    1. Reset all control boards by disconnecting power for 20 minutes.
    2. Check communication harness connectors for corrosion or damage.
    3. Test communication line resistance and signal integrity.
    4. Isolate components to identify which one is not responding.
    5. Replace faulty control board or communication module.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F04

    How to Fix Kenmore Dryer Error F04

    Problem: Thermistor circuit failure during heating cycle

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Locate thermistor sensor and wiring harness.
    4. Inspect wiring for damage, corrosion, or loose connections.
    5. Test sensor resistance at various temperatures with multimeter.
    6. Check continuity of sensor circuit from control board.
    7. If sensor is faulty, replace thermistor assembly.
    8. If wiring is damaged, repair or replace wire harness section with proper gauge wire.
    9. Clean electrical contacts with contact cleaner.
    10. Restore power and test heating cycle operation with temperature verification.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error E24

    How to Fix Kenmore Dishwasher Error E24

    Problem: Drain pump blocked or failed to operate

    How to Fix Dishwasher Error

    1. Remove and clean drain pump assembly.
    2. Check drain hose for kinks or blockages.
    3. Inspect drain pump impeller for debris or damage.
    4. Test drain pump motor windings and capacitor.
    5. Verify voltage to drain pump during drain cycle.
    6. Replace drain pump assembly if necessary.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F03

    How to Fix Kenmore Dryer Error F03

    Problem: Thermistor open circuit – temperature sensor failure

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Locate thermistor sensor on blower housing.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter (should not read infinite resistance).
    6. Inspect wiring harness for damage, cuts, or disconnections.
    7. If sensor is open, remove mounting screws and extract old sensor.
    8. Install new thermistor assembly and secure mounting screws.
    9. Check continuity of wiring harness between sensor and control board.
    10. Reconnect all components and test heating cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error E25

    How to Fix Kenmore Dishwasher Error E25

    Problem: Water level sensor fault or float switch failure

    How to Fix Dishwasher Error

    1. Check float switch assembly for proper movement and continuity.
    2. Inspect water level sensor tube for blockages or kinks.
    3. Test pressure switch operation at different water levels.
    4. Verify sensor wiring connections and resistance values.
    5. Replace water level sensor assembly if faulty.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.