Category: Kenmore

  • How to Fix Kenmore Dishwasher Error F22

    How to Fix Kenmore Dishwasher Error F22

    Problem: Heater relay stuck closed or failed open

    How to Fix Dishwasher Error

    1. Disconnect power and access control board.
    2. Test heater relay contacts for proper operation.
    3. Check relay coil resistance (should be 100-200 ohms).
    4. Inspect relay contacts for welding or carbon buildup.
    5. Test voltage to heating element when relay should be off.
    6. Replace control board if relay is faulty.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F01

    How to Fix Kenmore Washer Error F01

    Problem: EEPROM error on main control board

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel access cover.
    3. Inspect main control board for burnt components or damaged traces.
    4. Check all wire harness connections for proper seating and corrosion.
    5. Test voltage supply to control board.
    6. If board shows physical damage, document all wire connections before removal.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new main control board assembly.
    9. Reconnect all harnesses in correct positions.
    10. Power up and run diagnostic cycle to verify operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F16

    How to Fix Kenmore Dryer Error F16

    Problem: High limit thermostat relay failure on control board

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel access cover.
    3. Inspect main control board for burnt high limit relay contacts.
    4. Test high limit thermostat operation during overheating conditions.
    5. Check voltage supply to thermostat circuit.
    6. If relay is faulty, document all wire connections.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new main control board assembly.
    9. Reconnect all harnesses and test high limit safety functions.
    10. Run heating cycle to verify proper temperature control.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F15

    How to Fix Kenmore Dryer Error F15

    Problem: Flame sensor relay failure on control board

    How to Fix Dryer Error

    1. Turn off power and gas supply to dryer.
    2. Remove control panel access cover.
    3. Inspect main control board for burnt flame sensor relay contacts.
    4. Test flame sensor operation during combustion.
    5. Check voltage supply to flame sensor circuit.
    6. If relay is faulty, document all wire connections.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new main control board assembly.
    9. Reconnect all harnesses and restore gas supply.
    10. Test flame detection and safety shutdown functions.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F14

    How to Fix Kenmore Dryer Error F14

    Problem: Gas valve relay failure on control board

    How to Fix Dryer Error

    1. Turn off power and gas supply to dryer.
    2. Remove control panel access cover.
    3. Inspect main control board for burnt gas valve relay contacts.
    4. Test gas valve operation during ignition sequence.
    5. Check voltage supply to gas valve circuit.
    6. If relay is faulty, document all wire connections.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new main control board assembly.
    9. Reconnect all harnesses and restore gas supply.
    10. Test gas valve operation and flame safety functions.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F23

    How to Fix Kenmore Dishwasher Error F23

    Problem: Pressure switch stuck or out of calibration

    How to Fix Dishwasher Error

    1. Disconnect pressure switch hose and blow through it to clear blockages.
    2. Test pressure switch operation with multimeter while applying air pressure.
    3. Check pressure switch mounting and alignment.
    4. Verify pressure switch calibration against specifications.
    5. Replace pressure switch if it doesn’t switch at correct pressure levels.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F24

    How to Fix Kenmore Dishwasher Error F24

    Problem: Flow meter malfunction or incorrect water measurement

    How to Fix Dishwasher Error

    1. Access flow meter assembly and check for debris.
    2. Inspect impeller for free rotation and damage.
    3. Test flow meter sensor output with multimeter during water flow.
    4. Check flow meter wiring harness for damage.
    5. Verify flow meter calibration against actual water usage.
    6. Replace flow meter assembly if readings are inaccurate.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F13

    How to Fix Kenmore Dryer Error F13

    Problem: Igniter relay failure on gas dryer control board

    How to Fix Dryer Error

    1. Turn off power and gas supply to dryer.
    2. Remove control panel access cover.
    3. Inspect main control board for burnt igniter relay contacts.
    4. Test igniter operation during heating cycle start.
    5. Check voltage supply to igniter circuit.
    6. If relay is faulty, document all wire connections.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new main control board assembly.
    9. Reconnect all harnesses and restore gas supply.
    10. Test ignition sequence and flame operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F25

    How to Fix Kenmore Dishwasher Error F25

    Problem: Turbidity sensor (water clarity) failure

    How to Fix Dishwasher Error

    1. Clean turbidity sensor lens with soft cloth and mild detergent.
    2. Check sensor wiring connections for corrosion or damage.
    3. Test sensor output signal during wash cycle.
    4. Verify sensor mounting and alignment in water path.
    5. Replace turbidity sensor if cleaning and testing fails to restore function.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F26

    How to Fix Kenmore Dishwasher Error F26

    Problem: Motor control module communication fault

    How to Fix Dishwasher Error

    1. Reset all control boards by disconnecting power for 15 minutes.
    2. Check motor control harness connections and wiring integrity.
    3. Test communication signals between main control and motor module.
    4. Inspect motor control board for visible damage or component failure.
    5. Replace motor control module if communication cannot be restored.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes