Category: Kenmore

  • How to Fix Kenmore Washer Error F07

    How to Fix Kenmore Washer Error F07

    Problem: Motor speed sensor error during operation

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove front lower access panel.
    3. Locate motor speed sensor near drive motor.
    4. Inspect sensor mounting and alignment.
    5. Test sensor output signal with multimeter during manual rotation.
    6. Check wiring harness for damage or pinched wires.
    7. Clean sensor and target area with electrical contact cleaner.
    8. If sensor is faulty, disconnect electrical connector and remove mounting screws.
    9. Install new motor speed sensor with proper alignment.
    10. Test spin cycle operation at various speeds to verify proper sensing.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F23

    How to Fix Kenmore Dryer Error F23

    Problem: Temperature sensor calibration error during operation

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Locate thermistor sensor on heating assembly.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room tempeature.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is out of calibration range, remove mounting screws.
    8. Install new thermistor assembly with proper alignment.
    9. Reconnect electrical connector and verify proper seating.
    10. Run diagnostic cycle to clear error and verify temperature readings.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F06

    How to Fix Kenmore Washer Error F06

    Problem: Drive motor tachometer error – unable to detect motor speed

    How to Fix Washer Error

    1. Turn off power supply.
    2. Remove front access panel.
    3. Locate motor and tachometer sensor.
    4. Inspect motor wiring harness for damage or loose connections.
    5. Test tachometer sensor resistance with multimeter.
    6. Check motor brushes for wear or damage (if applicable).
    7. Test motor windings for proper resistance readings.
    8. If tachometer sensor is faulty, replace sensor assembly.
    9. If motor is faulty, replace entire drive motor assembly.
    10. Reconnect all components and test spin cycle operation at various speeds.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F22

    How to Fix Kenmore Dryer Error F22

    Problem: Temperature sensor circuit failure during cool-down

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Locate thermistor sensor wiring harness.
    4. Inspect wiring for damage, corrosion, or loose connections.
    5. Test sensor resistance at various temperatures.
    6. Check continuity of sensor circuit from control board.
    7. If sensor is faulty, replace thermistor assembly.
    8. If wiring is damaged, repair or replace wire harness section.
    9. Clean electrical contacts with contact cleaner.
    10. Restore power and test cool-down cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F05

    How to Fix Kenmore Washer Error F05

    Problem: NTC temperature sensor circuit failure

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove lower front access panel.
    3. Locate temperature sensor wiring harness.
    4. Inspect wiring for damage, corrosion, or loose connections.
    5. Test sensor resistance at various temperatures with multimeter.
    6. Check continuity of sensor circuit from control board.
    7. If sensor is faulty, replace temperature sensor assembly.
    8. If wiring is damaged, repair or replace wire harness section.
    9. Clean electrical contacts with contact cleaner.
    10. Restore power and test heating cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F21

    How to Fix Kenmore Dryer Error F21

    Problem: Temperature sensor failure – heater overheating

    How to Fix Dryer Error

    1. Turn off power supply immediately.
    2. Allow dryer to cool completely.
    3. Remove rear access panel.
    4. Locate thermistor sensor on heater assembly.
    5. Disconnect electrical connector from sensor.
    6. Test sensor resistance with multimeter.
    7. Inspect high limit thermostat and thermal fuse for continuity.
    8. If sensor is faulty, remove mounting screws and replace sensor.
    9. Check heater element for short circuits or grounding issues.
    10. Restore power and test heating cycle with temperature monitoring.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F16

    How to Fix Kenmore Dishwasher Error F16

    Problem: Door lock mechanism failure or safety interlock fault

    How to Fix Dishwasher Error

    1. Check door latch alignment and mechanical operation.
    2. Test door lock solenoid for continuity and proper engagement.
    3. Inspect door switch contacts for corrosion or damage.
    4. Verify control board door lock signals.
    5. Replace door lock assembly if mechanical or electrical failure detected.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F04

    How to Fix Kenmore Washer Error F04

    Problem: Door lock failure or communication error

    How to Fix Washer Error

    1. Turn off power supply.
    2. Open washer door fully.
    3. Remove door lock assembly access panel.
    4. Inspect door lock mechanism for physical damage or debris.
    5. Check door strike plate alignment with lock mechanism.
    6. Test door lock solenoid with multimeter for proper resistance.
    7. If lock assembly is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace door lock assembly.
    9. Ensure proper alignment during installation.
    10. Test door lock function and clear error code through diagnostic mode.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F17

    How to Fix Kenmore Dishwasher Error F17

    Problem: Circulation pump motor failure or blocked impeller

    How to Fix Dishwasher Error

    1. Access circulation pump assembly and check for debris.
    2. Inspect impeller for damage or blockage.
    3. Test motor windings for proper resistance and insulation.
    4. Check pump capacitor for bulging or leakage.
    5. Verify voltage to pump motor during wash cycle.
    6. Replace circulation pump assembly if necessary.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F20

    How to Fix Kenmore Dryer Error F20

    Problem: Temperature sensor failure – heater not reaching temperature

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Locate thermistor sensor on blower housing.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications.
    7. If sensor is faulty, remove mounting screws and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Inspect heater element connections for proper contact.
    10. Restore power and test heating cycle with temperature verification.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.