Category: Kenmore

  • How to Fix Kenmore Dryer Error tE

    How to Fix Kenmore Dryer Error tE

    Problem: Thermistor error – temperature sensor failure

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Locate thermistor sensor on blower housing or heater assembly.
    4. Disconnect electrical connector from thermistor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is out of range, remove mounting screws and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Clean sensor mounting area and ensure proper sealing.
    10. Reconnect electrical connector and test temperature readings during cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F24

    How to Fix Kenmore Washer Error F24

    Problem: Temperature sensor circuit failure during heating cycle

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove lower front access panel.
    3. Locate temperature sensor on heater assembly or tub.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance at various temperatures with multimeter.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is faulty, remove mounting screw and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Inspect heater element connections for proper contact.
    10. Restore power and test heating cycle with temperature verification.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error AF

    How to Fix Kenmore Dryer Error AF

    Problem: Airflow restriction – lint filter or vent blockage

    How to Fix Dryer Error

    1. Turn off power supply and allow dryer to cool.
    2. Remove and clean lint filter thoroughly with warm water and soap.
    3. Inspect lint filter housing for debris buildup.
    4. Check dryer vent hose for kinks, blockages, or excessive length.
    5. Disconnect vent hose from dryer and clean interior duct.
    6. Inspect external vent hood for obstructions (bird nests, debris).
    7. Clean moisture sensor bars inside drum with rubbing alcohol.
    8. Check blower wheel for debris or damage.
    9. Verify proper airflow by feeling exhaust during operation.
    10. Test drying cycle performance after cleaning all components.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F23

    How to Fix Kenmore Washer Error F23

    Problem: Control board overheating protection activated

    How to Fix Washer Error

    1. Turn off pwer and allow washer to cool for 30 minutes.
    2. Remove control panel and main access covers.
    3. Inspect control boards for signs of overheating or burnt components.
    4. Check cooling vents and fans for blockages or dust buildup.
    5. Clean all cooling vents and fan blades with compressed air.
    6. Verify proper airflow around control boards.
    7. Test temperature sensors on control boards.
    8. If board shows heat damage, replace affected control board.
    9. Check for overloaded circuits or voltage fluctuations.
    10. Test operation under normal load conditions to verify cooling.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error PF

    How to Fix Kenmore Dryer Error PF

    Problem: Power failure during cycle operation

    How to Fix Dryer Error

    1. Check household circuit breaker for tripped condition.
    2. Verify power outlet is functioning with another appliance.
    3. Inspect power cord for damage or loose connections.
    4. Check dryer power cord connection at terminal block inside machine.
    5. Test voltag at terminal block with multimeter (should read 240V).
    6. If power was restored, press START/PAUSE button to resume cycle.
    7. If cycle won’t restart, disconnect power for 5 minutes to reset control boards.
    8. Check for blown fuses on control boards if accessible.
    9. Inspect main power supply wiring for damage or corrosion.
    10. Test dryer operation after power restoration and reset procedures.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F22

    How to Fix Kenmore Washer Error F22

    Problem: Door lock failure during high-speed spin

    How to Fix Washer Error

    1. Turn off power supply.
    2. Open washer door fully.
    3. Inspect door lock mechanism for wear or damage.
    4. Test door lock solenoid with multimeter under load conditions.
    5. Check door strike plate alignment and condition.
    6. Inspect door gasket for proper sealing and alignment.
    7. If lock assembly fails during high-speed tests, replace entire assembly.
    8. Verify proper torque on mounting screws during installation.
    9. Test door lock function at various spin speeds.
    10. Ensure safety interlocks are functioning properly before final testing.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F84

    How to Fix Kenmore Dryer Error F84

    Problem: Door switch failure during heating cycle

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Open dryer door fully.
    3. Inspect door switch mechanism for heat damage.
    4. Test door switch continuity with multimeter when hot and cold.
    5. Check door strike plate alignment with switch mechanism.
    6. Inspect door switch wiring for heat damage or corrosion.
    7. If door switch is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace door switch assembly.
    9. Ensure proper alignment during installation.
    10. Test door closure and heating cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F21

    How to Fix Kenmore Washer Error F21

    Problem: Long drain – clogged drain system or pump failure

    How to Fix Washer Error

    1. Turn off power supply.
    2. Remove lower front access panel.
    3. Check drain hose for kinks, blockages, or improper routing.
    4. Remove drain pump access cover and clean filter debris.
    5. Inspect drain pump impeller for damage or obstructions.
    6. Test drain pump motor resistance with multimeter.
    7. Check drain pump wiring for corrosion or damage.
    8. If pump is weak or clogged, replace drain pump assembly.
    9. Ensure drain hose has proper high loop installation.
    10. Test drain cycle timing and verify complete drainage.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error F83

    How to Fix Kenmore Dryer Error F83

    Problem: Door switch failure during high-speed operation

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Open dryer door fully.
    3. Inspect door lock mechanism for wear or damage.
    4. Test door switch resistance with multimeter under load conditions.
    5. Check door strike plate alignment and condition.
    6. Inspect door gasket for proper sealing and alignment.
    7. If switch assembly fails during high-speed tests, replace entire assembly.
    8. Verify proper torque on mounting screws during installation.
    9. Test door switch function at various speeds.
    10. Ensure safety interlocks are functioning properly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error F20

    How to Fix Kenmore Washer Error F20

    Problem: No water detected – inlet valve failure or supply issue

    How to Fix Washer Error

    1. Turn off power and check household water supply valves.
    2. Verify water pressure at supply lines (minimum 20 PSI required).
    3. Remove lower front access panel.
    4. Inspect water inlet valve screens for debris or mineral buildup.
    5. Clean inlet valve filter screens with vinegar solution.
    6. Test inlet valve solenoids with multimeter for proper resistance.
    7. If valve is faulty, disconnect water supply lines and electrical connector.
    8. Remove mounting screws and replace water inlet valve assembly.
    9. Restore water and power connections.
    10. Test fill cycle operation and timing.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes