Category: Dishwasher

How to Fix Kenmore Dishwasher Error 9-2
Problem: Diverter motor stuck on

How to Fix 9-2 Error
1. This error indicates the diverter motor is stuck on, which is usually caused by a failed relay on the main control board.
2. Shut off power to the dishwasher at the circuit breaker.
3. Locate and access the main electronic control board.
4. Carefully disconnect all wire harnesses and replace the old board with the new one.
5. Reassemble the dishwasher and restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error 9-2: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error 9-3
Problem: Diverter disc is missing

How to Fix 9-3 Error
1. Disconnect power to the dishwasher.
2. This repair requires accessing the sump assembly at the bottom of the dishwasher tub.
3. Remove the lower dish rack, spray arm, and filter assembly to expose the sump.
4. The diverter motor and disc are located within this assembly. You will need to disassemble the sump to access the diverter.
5. If the disc is missing, a new one must be installed. This part number can vary, so it’s best to find it based on your dishwasher’s model number.
6. Reassemble the sump, filters, and spray arm, then restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error 9-3: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error 9-4
Problem: Lower spray arm error

How to Fix 9-4 Error
1. Disconnect power to the dishwasher.
2. This error points to a problem with a motorized lower spray arm. Access the sump area by removing the lower rack and filter assembly.
3. Check the wiring to the lower spray arm motor for any loose or damaged connections.
4. If the wiring is good, the motor itself has likely failed.
5. The motor is part of the sump assembly and will need to be uninstalled and replaced.
6. Reassemble the sump and restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error 9-4: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error Clean Light Stays On
Problem: Door switch assembly stuck; dishwasher won’t start new cycle until door opened after previous cycle

How to Fix Clean Light Stays On Error
1. Open the dishwasher door completely to reset the control panel.
2. Close the door firmly.
3. The dishwasher should now be ready to start a new cycle. This issue occurs when the door isn’t opened after the previous cycle finishes.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error Clean Light Stays On: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Kenmore dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

Kenmore dishwasher drain pump

Common replacement category: Drain pump

Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.

Confidence: Medium
This category can be relevant for drain and standing-water symptoms after filter, sump, and hose checks.

Search Amazon for Kenmore dishwasher drain pump

Kenmore dishwasher water inlet valve

Common replacement category: Water inlet valve

Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.

Confidence: Medium
This category can be relevant for fill faults after supply, float, and inlet screen checks.

Search Amazon for Kenmore dishwasher water inlet valve

Kenmore dishwasher circulation pump

Common replacement category: Circulation pump / wash motor

Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.

Confidence: Medium
This category can be relevant for weak wash or spray-arm symptoms after filter and spray-arm checks.

Search Amazon for Kenmore dishwasher circulation pump

Before ordering: match the part to the complete Kenmore dishwasher model number on the appliance tag.

When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026
How to Fix Kenmore Dishwasher Error Console Light Blinks Rapidly
Problem: Stuck button detected on control panel

How to Fix Console Light Blinks Rapidly Error
1. Disconnect the dishwasher from power at the circuit breaker.
2. Open the dishwasher door and remove the screws holding the inner door panel to access the control panel.
3. Disconnect the ribbon cable that connects the user interface control panel to the main control board.
4. Reconnect the power and wait to see if the error code returns. If it does not, the user interface control panel is faulty and needs to be replaced.
5. If the error persists, the main control board is likely the issue.
6. Replace the faulty component, reassemble the door, and restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error Console Light Blinks Rapidly: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026
How to Fix Kenmore Dishwasher Error F10E3
Problem: Drying fan / vent failure (alternate format)

How to Fix F10E3 Error
1. This is an alternate code for a drying fan failure, same as code 10-
2. Disconnect power to the dishwasher.
3. Remove the inner door panel to access the drying fan assembly.
4. Check the wire harness connection to the fan motor.
5. If the connection is secure, the fan motor is faulty and must be replaced.
6. Install the new fan assembly, reconnect wiring, and reassemble the door.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F10E3: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026
How to Fix Kenmore Dishwasher Error F4E1
Problem: Communication error between control board and circulation pump motor

How to Fix F4E1 Error
1. Disconnect power to the dishwasher at the circuit breaker.
2. Pull the dishwasher out from under the counter to access the circulation pump and motor assembly.
3. Check the wire harness connection between the main control board and the circulation pump motor. Ensure it is secure and the wires are not damaged.
4. If the wiring is intact, the circulation pump and motor assembly has likely failed and needs to be replaced.
5. Disconnect hoses and mounting brackets, remove the old pump, and install the new one.
6. Reconnect all hoses and wiring, slide the dishwasher back into place, and restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F4E1: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026
How to Fix Kenmore Dishwasher Error F5E2
Problem: Control detects door not opening between cycles

How to Fix F5E2 Error
1. This error is functionally the same as code 5-
2. The control board did not detect the door opening between cycles.
3. Always open the door for several seconds after a cycle is complete.
4. If the error persists, the door latch assembly’s microswitch is likely failing. Disconnect power.
5. Disassemble the door to access the latch assembly.
6. Test the switches with a multimeter. If a switch is faulty, replace the entire door latch assembly.
7. Reassemble the door and restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F5E2: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026
How to Fix Kenmore Dishwasher Error F6E2
Problem: Water inlet valve failure

How to Fix F6E2 Error
1. Shut off the water supply and electrical power to the dishwasher.
2. The water inlet valve is usually located at the front left corner, behind the lower access panel.
3. Place a towel under the valve to catch any water.
4. Disconnect the water supply line and the outlet hose from the valve.
5. Disconnect the wire harness.
6. Remove the mounting screw(s) and replace the old valve with the new one.
7. Reconnect hoses and wiring, turn the water supply back on, check for leaks, and then restore power.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F6E2: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026
How to Fix Kenmore Dishwasher Error F6E3
Problem: Suds or error in water pump; excessive suds detected

How to Fix F6E3 Error
1. This error means too many suds were detected. This is almost always caused by using the wrong type of soap (e.g., hand dish soap instead of automatic dishwasher detergent).
2. Open the dishwasher and remove as many suds as possible.
3. Run a rinse-only cycle to clear out the remaining suds. You may need to run it multiple times.
4. To prevent this, only use detergent specifically designed for automatic dishwashers.
What to Check Next on This Kenmore Dishwasher

Kenmore Dishwasher Error F6E3: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.
If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Kenmore dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

Kenmore dishwasher drain pump

Common replacement category: Drain pump

Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.

Confidence: Medium
This category can be relevant for drain and standing-water symptoms after filter, sump, and hose checks.

Search Amazon for Kenmore dishwasher drain pump

Kenmore dishwasher water inlet valve

Common replacement category: Water inlet valve

Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.

Confidence: Medium
This category can be relevant for fill faults after supply, float, and inlet screen checks.

Search Amazon for Kenmore dishwasher water inlet valve

Kenmore dishwasher circulation pump

Common replacement category: Circulation pump / wash motor

Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.

Confidence: Medium
This category can be relevant for weak wash or spray-arm symptoms after filter and spray-arm checks.

Search Amazon for Kenmore dishwasher circulation pump

Before ordering: match the part to the complete Kenmore dishwasher model number on the appliance tag.

When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

[OK]Drain pump or circulation pump failure

[OK]Leaking tub, door, or float-switch issues

[OK]Heater or control failures on an older unit

[OK]Repeated poor washing or drying performance

Recommended Dishwasher Replacement Options

Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
March 17, 2026