Category: GE

  • How to Fix GE Dryer Error 010

    How to Fix GE Dryer Error 010

    Problem: Empty drum detection trip – sensor rods fail to detect weight in drum

    How to Fix 010 Error

    1. This code means the dryer’s automatic cycle ran but the moisture sensor rods did not detect a wet load.
    2. This commonly happens if you try to dry a single, very small item that doesn’t make consistent contact with the two metal sensor bars inside the drum.
    3. Find the two metal strips inside the dryer drum (usually near the lint filter opening) and clean them with a cloth and rubbing alcohol to remove any invisible residue from fabric softener, which can insulate them.
    4. Add a few more items to the load to ensure proper tumbling and contact with the sensors.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error 011

    How to Fix GE Dryer Error 011

    Problem: Blocked vent detected – airflow obstruction in exhaust duct

    How to Fix 011 Error

    1. This is a critical safety warning. UNPLUG THE DRYER before proceeding.
    2. Pull the lint filter out and clean it thoroughly. If you use dryer sheets, wash the filter with warm, soapy water and a soft brush to remove waxy residue, then let it dry completely.
    3. Disconnect the vent hose from the back of the dryer. Use a vacuum and a vent cleaning brush to clean out the entire length of the hose and the wall ducting all the way to the outside.
    4. Check the exterior vent flap to ensure it opens and closes freely and is not blocked by debris, snow, or animal nests.
    5. Reconnect the vent hose, ensuring there are no sharp kinks or crushed sections.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error 014

    How to Fix GE Dryer Error 014

    Problem: Door latch error – door latch pulsating air issue

    How to Fix 014 Error

    1. UNPLUG THE DRYER. This is a fault related to the door latch assembly.
    2. The repair is to replace the door latch. This requires accessing the inside of the front panel.
    3. Depending on the model, remove the top panel, then the control console, and finally the front panel.
    4. The latch assembly is screwed to the front of the cabinet. Disconnect its wire harness, remove the screws, and install the new latch.
    5. Reconnect the wiring and reassemble the dryer in reverse order.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error 019

    How to Fix GE Dryer Error 019

    Problem: Door latch lost in run – door latch failed during operation

    How to Fix 019 Error

    1. Disconnect the dryer from its power source.
    2. This error means the door latch mechanism failed while the dryer was running. You will need to access the latch assembly inside the front panel.
    3. Open the dryer door. Depending on the model, you may need to remove the top panel and then the front panel to get to the latch.
    4. Once accessed, disconnect the wire harness from the latch assembly. Remove the screws holding the old latch in place.
    5. Install the new latch assembly, secure it with its screws, and reconnect the wire harness. Reassemble the dryer panels.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error 18

    How to Fix GE Dryer Error 18

    Problem: Pump filter needs cleaning – drain restriction detected (combo units)

    How to Fix 18 Error

    1. This code applies to washer/dryer combo units and indicates the drain pump filter is clogged.
    2. Locate the small access door on the bottom front of the machine.
    3. Place a shallow pan and a towel under the access door. Open the door and locate the small drain hose. Uncap it and let the residual water drain into the pan.
    4. Once drained, twist the large pump filter cap counter-clockwise and pull it out. Be prepared for more water.
    5. Clean all lint, hair, and debris from the filter. Check inside the filter housing for any obstructions. Reinsert the filter and tighten it securely. Replace the drain hose cap and close the access door.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error 353

    How to Fix GE Dryer Error 353

    Problem: Lint filter clogged with fabric softener residue (combo units)

    How to Fix 353 Error

    1. This code appears on washer/dryer combo units and means the lint filter is clogged with fabric softener residue, blocking airflow.
    2. Remove the lint filter from its housing.
    3. Take the filter to a sink and scrub it with a soft brush (like a toothbrush) and warm, soapy water to dissolve the waxy buildup.
    4. Rinse the filter thoroughly and let it air dry completely before reinserting it into the dryer.
    5. Avoid using liquid fabric softener in the washer, as this is the primary cause. Use dryer sheets or wool dryer balls instead.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error CL

    How to Fix GE Dryer Error CL

    Problem: Control Lock / Child Lock active – control panel buttons disabled

    How to Fix CL Error

    1. This is not an error. It means ‘Control Lock’ or ‘Child Lock’ is active, and the buttons are disabled to prevent accidental changes.
    2. Look for a button on the control panel labeled ‘Control Lock’ or that has a small lock icon next to it (often the ‘Light’ or ‘Steam’ button).
    3. Press and hold this specific button for 3 to 5 seconds.
    4. The ‘CL’ message should disappear, and the controls will be unlocked.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error Cd

    How to Fix GE Dryer Error Cd

    Problem: Cool Down – dryer is in cool-down phase at end of cycle

    How to Fix Cd Error

    1. This is not an error code. It indicates the dryer has finished the heated portion of its cycle and is now in the ‘Cool Down’ phase.
    2. The drum will continue to tumble with no heat to cool the clothes down, reduce wrinkling, and make them safer to handle.
    3. You can either wait for the cycle to finish completely or press the ‘Power’ button to stop it and remove your clothes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error Check Vent

    How to Fix GE Dryer Error Check Vent

    Problem: Vent restriction indicator – reduced airflow in exhaust vent detected

    How to Fix Check Vent Error

    1. This is a maintenance reminder indicating restricted airflow. It is a critical safety issue to address immediately. Unplug the dryer.
    2. Clean the lint screen inside the door opening.
    3. Disconnect the flexible vent hose from the back of the dryer and clean it out completely using a vacuum or brush.
    4. Clean the entire length of the ductwork inside your wall all the way to the exterior vent cap.
    5. Make sure the outside vent cap flap is not stuck shut or blocked by nests or debris. Reassemble and run a test cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error Do

    How to Fix GE Dryer Error Do

    Problem: Door Open – alias of dE; door not closed

    How to Fix Do Error

    1. This is an alias for the ‘dE’ (Door Error) code. First, open the door and close it firmly.
    2. If the code persists, the door switch has failed. UNPLUG THE DRYER.
    3. Access the door switch by removing the top or front panel. It’s located in the frame where the door closes.
    4. Disconnect the wiring and use a multimeter to test the switch for continuity when its plunger is pressed. If it fails the test, it needs to be replaced.
    5. Install the new switch, reconnect the wiring, and reassemble the dryer.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Ge error codes: Ge Error Codes