Category: Electrolux

  • How to Fix Electrolux Dryer Error E86

    How to Fix Electrolux Dryer Error E86

    Error Code: E86 Difficulty: Easy

    Problem: Incorrect selector setting signal.

    How to Fix E86 Error (Step-by-Step)

    1. Turn the cycle selector knob to a different cycle setting than the one that was active when the error occurred.
    2. Unplug the dryer from the power outlet, or switch off the corresponding circuit breaker.
    3. Wait for at least 5-10 minutes to allow the internal electronics to fully reset.
    4. Plug the dryer back in or turn the circuit breaker back on.
    5. Select a new cycle and press ‘Start’ to see if the error has been resolved.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E35

    How to Fix Electrolux Dryer Error E35

    Error Code: E35 Difficulty: Easy

    Problem: Pressure sensor indicates water overfill.

    How to Fix E35 Error (Step-by-Step)

    1. Check the dryer’s lint filter and clean it thoroughly if it is clogged.
    2. Ensure the dryer’s exhaust vent is not blocked or restricted.
    3. Straighten any kinks in the flexible vent hose behind the dryer.
    4. Clean the entire length of the dryer vent system, from the dryer to the outside of the house.
    5. Reduce the size of the load in the dryer to allow for better airflow.
    6. Once these checks are complete, try running a cycle again.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E15

    How to Fix Electrolux Dryer Error E15

    Error Code: E15 Difficulty: Easy

    Problem: Vacuum switch – The vacuum switch does not shut within 5 seconds after the dryer is started.

    How to Fix E15 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Disconnect the flexible vent hose from the back of the dryer.
    3. Look inside the hose and the dryer’s exhaust port for any heavy accumulation of lint and clean it out.
    4. Go outside and check the exterior vent cap. Ensure the damper flap is not stuck shut and clear away any lint, leaves, or other debris.
    5. For long vent runs, it may be necessary to use a vent cleaning brush kit to clear the entire length of the ducting in the wall.
    6. Once the entire vent path is clear, securely reattach the hose, plug the dryer in, and run a test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E00

    How to Fix Electrolux Dryer Error E00

    Error Code: E00 Difficulty: Easy

    Problem: No error detected during the last cycle.

    How to Fix E00 Error (Step-by-Step)

    1. This code is informational and simply means the last drying cycle finished without any problems being detected by the system.
    2. No repair or action is needed from you and confirm the error stays cleared during a full test cycle.
    3. To clear the code from the display, press the ‘Power’ or ‘Cancel’ button.
    4. After clearing the code, you can load the dryer and start a new cycle as you normally would.
    5. Turn the appliance off, wait about 2 minutes, then turn it back on.
    6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error CL

    How to Fix Electrolux Dryer Error CL

    Error Code: CL Difficulty: Easy

    Problem: Close door – door switch error.

    How to Fix CL Error (Step-by-Step)

    1. Open the dryer door and check for any clothes, lint, or other items that might be blocking the door from closing completely.
    2. Inspect the area around the door latch and the opening on the dryer frame. Clean away any lint or debris with a cloth.
    3. Close the door firmly, making sure you hear a distinct ‘click’ sound, which indicates the latch has engaged properly.
    4. If the door appears closed but the error persists, gently press on the door to ensure the switch is fully activated.
    5. Visually inspect the plastic door latch and the metal strike on the dryer body for any signs of cracking, breakage, or misalignment. If damage is found, the door latch assembly may need to be replaced.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes