Category: Electrolux

  • How to Fix Electrolux Dryer Error E5H

    How to Fix Electrolux Dryer Error E5H

    Error Code: E5H Difficulty: Hard

    Problem: The motor voltage is too low (below 100 volts).

    How to Fix E5H Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet or shutting off the corresponding circuit breaker.
    2. Remove the screws securing the dryer’s top panel, which are typically located at the back of the machine. Slide the top panel off to access the internal components.
    3. Locate the inverter board. It is usually a small circuit board with multiple wire harnesses connected to it. Before disconnecting anything, take a clear photo of the board and its wire connections for reference.
    4. Carefully disconnect all wire harnesses from the old inverter board. Most connectors have a small locking tab that needs to be pressed to release the plug.
    5. Remove the screws that mount the inverter board to the dryer’s frame. Lift the old board out of the dryer.
    6. Position the new inverter board in the same location and secure it with the mounting screws. Do not overtighten the screws.
    7. Using your reference photo, reconnect all the wire harnesses to the correct terminals on the new board, ensuring each plug is fully seated and locked into place. Reassemble the dryer by sliding the top panel back on and securing it with the screws, then restore power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5F

    How to Fix Electrolux Dryer Error E5F

    Error Code: E5F Difficulty: Hard

    Problem: General error indicating damage to the FCV board.

    How to Fix E5F Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent any electrical shock.
    2. Remove the screws from the back of the dryer that hold the top panel in place, then lift the panel off.
    3. Locate the FCV board, which is also known as the inverter board. It is a small circuit board with multiple wire connections.
    4. Before disconnecting anything, take a clear picture of the board and its wire connections to use as a guide for reinstallation.
    5. Carefully unplug all the wire harnesses from the old board. Then, remove the mounting screws that hold it in place.
    6. Position the new inverter board, secure it with the mounting screws, and reconnect all the wire harnesses exactly as they were in your photo.
    7. Reinstall the top panel, plug the dryer in, and run a cycle to ensure the error is gone.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5E

    How to Fix Electrolux Dryer Error E5E

    Error Code: E5E Difficulty: Hard

    Problem: There is a communication error between the inverter and the main PCB.

    How to Fix E5E Error (Step-by-Step)

    1. Turn off the circuit breaker for the dryer and unplug it from the wall.
    2. Take off the dryer’s top panel by removing the screws at the back.
    3. Find the main control board and the inverter board inside the dryer.
    4. Visually check the communication cable that runs between these two boards for any obvious damage, like cuts or burn marks.
    5. Disconnect the communication cable from both boards and plug it back in, making sure the connections are snug and secure.
    6. If no damage is found and the connection is good, the error indicates a failure in either the main control board or the inverter board, requiring replacement of the faulty component.
    7. After replacing the suspected board, put the dryer back together, restore power, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137261100
    • 809160303
    • A17667001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5D

    How to Fix Electrolux Dryer Error E5D

    Error Code: E5D Difficulty: Hard

    Problem: A data transfer error has occurred between the inverter board and the main PCB.

    How to Fix E5D Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
    2. Remove the top panel of the dryer to get access to the electronic boards.
    3. Locate the main control board (PCB) and the separate inverter board.
    4. Carefully inspect the wiring harness that connects the two boards. Look for any loose plugs, pinched wires, or signs of damage.
    5. Unplug and firmly reseat the connectors on both the main PCB and the inverter board to ensure a secure connection.
    6. Replace the faulty board, carefully transferring all wire connections to the new one, then reassemble and test the dryer.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137261100
    • 809160303
    • A17667001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5C

    How to Fix Electrolux Dryer Error E5C

    Error Code: E5C Difficulty: Hard

    Problem: The input voltage to the inverter board is too high.

    How to Fix E5C Error (Step-by-Step)

    1. Unplug the dryer from the power outlet to ensure your safety.
    2. Using a multimeter, carefully check the voltage of the wall outlet to confirm it is supplying the correct voltage (typically 240V for an electric dryer).
    3. If the outlet voltage is excessively high, contact a qualified electrician to resolve the household wiring issue. Do not proceed with the repair.
    4. If the outlet voltage is correct, you will need to access and replace the inverter board. Remove the top panel of the dryer to access the internal components.
    5. Locate the inverter board. Take a picture of the wire connections for reference before disconnecting them.
    6. Carefully disconnect the wiring and remove the screws securing the old inverter board. Install the new board.
    7. Reconnect all wiring harnesses, reassemble the dryer, and plug it in to test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304523779

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5B

    How to Fix Electrolux Dryer Error E5B

    Error Code: E5B Difficulty: Hard

    Problem: The motor control board is receiving insufficient voltage.

    How to Fix E5B Error (Step-by-Step)

    1. Disconnect the power cord from the wall outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel of the dryer to access the main control board and motor control board.
    3. Check the main power supply to the dryer to ensure it is providing the correct voltage.
    4. Inspect the wiring between the main control board and the motor control board for any loose or damaged connections.
    5. Use a multimeter to test the voltage output from the main control board to the motor control board.
    6. If the voltage is insufficient, the main control board is likely faulty and needs to be replaced.
    7. Replace the board, reassemble the dryer, and restore power to check if the error is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137261100
    • 809160303
    • A17667001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5A

    How to Fix Electrolux Dryer Error E5A

    Error Code: E5A Difficulty: Hard

    Problem: The inverter board is overheated.

    How to Fix E5A Error (Step-by-Step)

    1. Unplug the dryer to prevent any electrical accidents and confirm the error stays cleared during a full test cycle.
    2. Remove the top and rear panels to locate the inverter board.
    3. Check for any obstructions around the inverter board that might be restricting airflow.
    4. Ensure the cooling fan for the inverter board is functioning correctly.
    5. If there are no airflow issues, the inverter board itself may be faulty and generating excessive heat.
    6. Replace the inverter board by carefully disconnecting the wire harnesses and removing the mounting screws.
    7. Install the new board, reassemble the dryer, and test for proper operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304523779

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E58

    How to Fix Electrolux Dryer Error E58

    Error Code: E58 Difficulty: Hard

    Problem: High current on motor phase.

    How to Fix E58 Error (Step-by-Step)

    1. Disconnect the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Access the motor and the inverter board by removing the dryer’s service panels.
    3. Examine the wires connecting the motor to the inverter board for any damage.
    4. If the wires are intact, the issue is likely with the motor or the inverter board.
    5. Test the motor windings with a multimeter to see if they are shorted.
    6. If the motor tests fine, the inverter board is the most likely cause of the problem and should be replaced.
    7. After replacing the faulty component, reassemble the dryer and plug it back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 137099100
    • 137261100

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E57

    How to Fix Electrolux Dryer Error E57

    Error Code: E57 Difficulty: Hard

    Problem: High current on inverter.

    How to Fix E57 Error (Step-by-Step)

    1. Unplug the dryer from its power source and confirm the error stays cleared during a full test cycle.
    2. Remove the necessary panels to access the inverter board and motor.
    3. Visually inspect the inverter board for any signs of burns or damage.
    4. Check the wiring between the inverter board and the motor for any loose or frayed connections.
    5. If the wiring is secure, the inverter board is likely the issue and needs to be replaced.
    6. Carefully disconnect all wires from the old inverter board and remove it.
    7. Install the new inverter board, reconnect all wiring, reassemble the dryer, and test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 137099100
    • 137261100

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E56

    How to Fix Electrolux Dryer Error E56

    Error Code: E56 Difficulty: Hard

    Problem: High motor current.

    How to Fix E56 Error (Step-by-Step)

    1. Turn off the power to the dryer at the circuit breaker.
    2. Open the dryer’s access panel to get to the motor.
    3. Check for any obstructions around the drum that could be causing the motor to work harder.
    4. Inspect the drive belt for signs of wear or damage and replace it if necessary.
    5. If the belt is fine and there are no obstructions, the motor itself may be faulty.
    6. Replace the motor by disconnecting it from its mount and the electrical connections.
    7. Install the new motor, reassemble the dryer, and restore power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 5304529782

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes