Category: Bosch

  • How to Fix Bosch Dryer Error CROSSED OUT SQUARE WITH CIRCLE

    How to Fix Bosch Dryer Error CROSSED OUT SQUARE WITH CIRCLE

    Error Code: CROSSED OUT SQUARE WITH CIRCLE Difficulty: Easy

    Problem: Do not tumble dry.

    How to Fix CROSSED OUT SQUARE WITH CIRCLE Error (Step-by-Step)

    1. This symbol indicates that the item of clothing is not suitable for tumble drying.
    2. Remove the item from the dryer immediately to prevent damage.
    3. Check the care label on the garment to confirm the drying instructions.
    4. Alternative drying methods may include line drying or flat drying.
    5. Failure to follow the care label instructions can lead to shrinking, melting, or other damage to the fabric.
    6. Always check the care labels on your laundry before using the dryer.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error DR

    How to Fix Bosch Dryer Error DR

    Error Code: DR Difficulty: Moderate

    Problem: Door is not properly closed or there is a drainage problem.

    How to Fix DR Error (Step-by-Step)

    1. First, ensure the dryer door is fully closed and latched. Listen for a ‘click’ to confirm it’s secure.
    2. Inspect the door switch for any visible damage or debris that may be preventing it from engaging.
    3. If the door is secure, check the drainage hose at the back of the dryer. Make sure it is not kinked, crushed, or blocked.
    4. Disconnect the drain hose and check for any obstructions inside the hose.
    5. If the issue persists, the door switch may be faulty and require replacement.
    6. Alternatively, there could be an internal blockage in the drain pump system that needs to be cleared.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E01

    How to Fix Bosch Dryer Error E01

    Error Code: E01 Difficulty: Moderate

    Problem: Lint filter is blocked.

    How to Fix E01 Error (Step-by-Step)

    1. Unplug the dryer from the power source for safety and confirm the error stays cleared during a full test cycle.
    2. Open the dryer door and locate the lint filter. It is usually just inside the door opening.
    3. Pull the lint filter straight up and out of its housing.
    4. Remove the accumulated lint from the filter screen with your fingers. Do not use water to clean it as this can cause other issues.
    5. Use a soft brush or a vacuum cleaner with a crevice tool to clean the lint filter housing area.
    6. Re-insert the clean, dry lint filter back into its housing until it clicks into place.
    7. If the error persists after thorough cleaning, the lint filter itself may be damaged or clogged with fine particles and require replacement.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E02

    How to Fix Bosch Dryer Error E02

    Error Code: E02 Difficulty: Moderate

    Problem: Lint filter is still blocked or wet.

    How to Fix E02 Error (Step-by-Step)

    1. Unplug the dryer for at least 30 minutes to allow it to reset.
    2. Remove the lint filter and wash it with warm, soapy water and a soft brush to remove any fabric softener residue.
    3. Rinse the filter thoroughly and allow it to air dry completely before reinserting it.
    4. While the filter is drying, use a vacuum cleaner to clean the lint filter housing and the vent pipe connected to the back of the dryer.
    5. Ensure the venting hose is not kinked or crushed, and that the exterior vent flap is opening freely.
    6. Once everything is clean and dry, reassemble and plug the dryer back in.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E06

    How to Fix Bosch Dryer Error E06

    Error Code: E06 Difficulty: Hard

    Problem: Heating circuit fault.

    How to Fix E06 Error (Step-by-Step)

    1. Disconnect the dryer from the power supply completely and confirm the error stays cleared during a full test cycle.
    2. For this repair, you will need to access the back of the dryer by removing the rear panel.
    3. Locate the heating element assembly, which is a large metal housing containing the heating coils.
    4. Use a multimeter to test the continuity of the heating element. A reading of infinity indicates a broken element that needs replacement.
    5. Also, test the high-limit thermostat and thermal fuse, which are typically mounted on the heating element housing. These should have continuity.
    6. If any of these components fail the continuity test, the entire heating element assembly should be replaced.
    7. This is a complex repair and may be best left to a qualified service if you are not comfortable working with electrical components.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E08

    How to Fix Bosch Dryer Error E08

    Error Code: E08 Difficulty: Hard

    Problem: Electronics fault.

    How to Fix E08 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
    2. Remove the top panel of the dryer by unscrewing the screws holding it in place, typically located at the back.
    3. Locate the control board, which is usually at the front of the dryer behind the control panel.
    4. Carefully disconnect all the wire harnesses connected to the old control board, taking a photo beforehand for reference.
    5. Remove the screws that secure the control board to the dryer frame and gently lift it out.
    6. Install the new control board, making sure it is properly aligned and secured with the screws.
    7. Reconnect all the wire harnesses to the new control board according to your reference photo and then reassemble the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dishwasher Error SALT SYMBOL (S-SHAPED ARROWS)

    How to Fix Bosch Dishwasher Error SALT SYMBOL (S-SHAPED ARROWS)

    Error Code: SALT SYMBOL (S-SHAPED ARROWS) Difficulty: Easy

    Problem: The dishwasher salt reservoir needs to be refilled.

    How to Fix SALT SYMBOL (S-SHAPED ARROWS) Error (Step-by-Step)

    1. Pull out the bottom rack completely to access the floor of the dishwasher.
    2. Locate the large, round cap for the salt reservoir, usually off to one side.
    3. Unscrew the cap by turning it counter-clockwise and set it aside. It is normal to see water inside the reservoir.
    4. Insert the funnel that came with your dishwasher into the opening.
    5. Pour only dishwasher-specific salt into the funnel until the reservoir is completely full.
    6. Remove the funnel and wipe away any loose salt granules from the threads of the opening.
    7. Screw the cap back on tightly and run a short rinse cycle to distribute the salt and clear the sensor.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E09

    How to Fix Bosch Dryer Error E09

    Error Code: E09 Difficulty: Hard

    Problem: Electronics fault.

    How to Fix E09 Error (Step-by-Step)

    1. Turn off the power to the dryer at the circuit breaker and unplug the appliance.
    2. Access the control board by removing the top panel of the dryer, which is usually secured by screws at the back.
    3. Identify the control board, typically found behind the front control panel.
    4. Take a clear picture of the wire connections before disconnecting them from the control board.
    5. Unscrew the mounting screws holding the control board in place and carefully remove it.
    6. Position the new control board in the same location and secure it with the mounting screws.
    7. Reconnect the wires to the new board as per your photo, reattach the top panel, and restore power to the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dishwasher Error WATER TAP SYMBOL

    How to Fix Bosch Dishwasher Error WATER TAP SYMBOL

    Error Code: WATER TAP SYMBOL Difficulty: Easy

    Problem: Problem with the water supply.

    How to Fix WATER TAP SYMBOL Error (Step-by-Step)

    1. Begin by checking the water supply valve connected to the dishwasher, typically located under your kitchen sink. Ensure the handle is turned fully counter-clockwise to the ‘on’ position.
    2. Pull the dishwasher out slightly from the cabinet to inspect the water inlet hose for any kinks or sharp bends that could restrict water flow.
    3. Gently straighten any part of the hose that is pinched or bent.
    4. Turn off the water supply valve. Place a small bucket or towel under the connection and unscrew the hose from the valve.
    5. Look inside the end of the hose for a small filter screen. Check if it is clogged with sediment or debris.
    6. Remove the screen with needle-nose pliers if possible and rinse it thoroughly under running water until clean. Re-insert the filter.
    7. Securely reattach the hose to the water supply valve, turn the water back on, and start a new cycle to clear the error.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)

    How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)

    Error Code: RED LIGHT ON FLOOR (INFOLIGHT) Difficulty: Easy

    Problem: The dishwasher is currently operating.

    How to Fix RED LIGHT ON FLOOR (INFOLIGHT) Error (Step-by-Step)

    1. Identify the red light shining on the floor beneath the dishwasher.
    2. Recognize that this ‘InfoLight’ is a standard feature indicating a wash cycle is in progress.
    3. Avoid opening the dishwasher door, as this will interrupt the cleaning and drying process.
    4. Allow the dishwasher to run undisturbed until the cycle is fully completed.
    5. The red light will automatically extinguish once the cycle has finished.
    6. You can now safely open the dishwasher and unload your clean dishes.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You