Category: Bosch

  • How to Fix Bosch Refrigerator Error E05

    How to Fix Bosch Refrigerator Error E05

    Error Code: E05 Difficulty: Moderate

    Problem: Ice maker sensor failure.

    How to Fix E05 Error (Step-by-Step)

    1. Disconnect the refrigerator from its power supply and confirm the error stays cleared during a full test cycle.
    2. Turn off the water supply to the ice maker and confirm the error stays cleared during a full test cycle.
    3. Remove the ice bin to gain access to the ice maker assembly.
    4. The ice maker sensor is part of the ice maker module. You may need to remove the ice maker to access it.
    5. Disconnect the wire harness connected to the ice maker and confirm the error stays cleared during a full test cycle.
    6. Locate and replace the faulty sensor within the ice maker assembly.
    7. Reinstall the ice maker, reconnect the wiring, turn the water supply back on, and restore power to the refrigerator.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00605015

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Refrigerator Error E07

    How to Fix Bosch Refrigerator Error E07

    Error Code: E07 Difficulty: Hard

    Problem: Condenser fan failure.

    How to Fix E07 Error (Step-by-Step)

    1. Completely disconnect the refrigerator from the power source by unplugging it from the wall outlet.
    2. Pull the refrigerator away from the wall to access the rear lower service panel.
    3. Remove the screws holding the service panel in place and set it aside.
    4. Locate the condenser fan, which is responsible for cooling the compressor. Take a photo of the wiring for reference.
    5. Disconnect the fan’s wire harness and remove the mounting screws or clips holding the fan assembly.
    6. Install the new condenser fan assembly, secure it with the mounting hardware, and reconnect the wire harness.
    7. Replace the rear service panel, plug the refrigerator back in, and carefully slide it back into place.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00618893
    • 11023751

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Refrigerator Error E04

    How to Fix Bosch Refrigerator Error E04

    Error Code: E04 Difficulty: Hard

    Problem: Freezer door is open.

    How to Fix E04 Error (Step-by-Step)

    1. First, ensure there are no items inside the freezer blocking the door from closing completely.
    2. Inspect the freezer door gasket for any signs of damage, such as rips or warping, that could prevent a proper seal.
    3. Clean the door gasket and the surface it touches on the refrigerator with a mild detergent to remove any dirt or stickiness.
    4. Check the alignment of the freezer door. If it appears to be sagging, you may need to adjust the hinges.
    5. Locate the door switch, which is usually a small plunger or magnetic switch along the door frame.
    6. Press and release the door switch to see if the interior light turns on and off. If it doesn’t, the switch may be faulty and require replacement.
    7. If the problem persists after these steps, it may indicate an issue with the door sensor or the main control board, which will require a professional service.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00678816
    • 00702092
    • 00744441

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F28

    How to Fix Bosch Washer Error F28

    Error Code: F28 Difficulty: Moderate

    Problem: Flow sensor malfunction or issue.

    How to Fix F28 Error (Step-by-Step)

    1. Disconnect the power cord of the washer from the electrical outlet.
    2. The flow sensor is part of the water inlet valve assembly, located where the water hoses connect to the washer.
    3. To access it, you will need to remove the back panel of the washer.
    4. Identify the flow sensor and disconnect the electrical wires connected to it.
    5. The flow sensor is often integrated with the inlet valve, so you may need to replace the entire valve assembly.
    6. Remove the old inlet valve assembly and install the new one, reconnecting the water hoses and the electrical wires.
    7. Secure the back panel and test the washer and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Refrigerator Error E03

    How to Fix Bosch Refrigerator Error E03

    Error Code: E03 Difficulty: Moderate

    Problem: Temperature-controlled drawer temperature sensor is defective.

    How to Fix E03 Error (Step-by-Step)

    1. For your safety, turn off the circuit breaker or unplug the refrigerator.
    2. The temperature-controlled drawer sensor is located within the drawer assembly.
    3. Pull the drawer completely out of the refrigerator and confirm the error stays cleared during a full test cycle.
    4. Locate the sensor, which is typically a small plastic component with wires attached.
    5. Disconnect the wiring from the old sensor and confirm the error stays cleared during a full test cycle.
    6. Remove the old sensor from its mounting clip or housing.
    7. Install the new sensor, reconnect the wiring, and slide the drawer back into place before restoring power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00618543
    • 00625294
    • 10011760

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F29

    How to Fix Bosch Washer Error F29

    Error Code: F29 Difficulty: Easy

    Problem: No water flow in the flow sensor detected.

    How to Fix F29 Error (Step-by-Step)

    1. First, check that the water supply faucets connected to the washer are fully turned on.
    2. Inspect the water inlet hoses for any kinks, twists, or blockages that could be restricting water flow.
    3. Turn off the water supply and unscrew the inlet hoses from the back of the washer.
    4. Check the small filter screens inside the water inlet ports on the washer for any debris or sediment and clean them thoroughly.
    5. Reconnect the hoses, turn the water back on, and start a new cycle to see if the issue is resolved.
    6. If the problem persists, the water inlet valve itself may be faulty and require replacement.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Refrigerator Error E02

    How to Fix Bosch Refrigerator Error E02

    Error Code: E02 Difficulty: Moderate

    Problem: Freezer compartment temperature sensor is faulty.

    How to Fix E02 Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet to prevent electrical shock.
    2. The freezer compartment temperature sensor is usually located on the back or side wall of the freezer interior.
    3. You may need to remove the freezer shelves and the back panel to access the sensor.
    4. Gently unplug the wire connector from the faulty sensor and confirm the error stays cleared during a full test cycle.
    5. Remove the screw or release the clip holding the sensor in place and take out the old sensor.
    6. Position the new sensor and secure it with the original screw or clip.
    7. Reconnect the wire harness, reattach the back panel, replace the shelves, and plug the refrigerator back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00618543
    • 00625294
    • 00627548

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dishwasher Error E30

    How to Fix Bosch Dishwasher Error E30

    Error Code: E30 Difficulty: Hard

    Problem: Voltage is too high.

    How to Fix E30 Error (Step-by-Step)

    1. Turn off the circuit breaker for the dishwasher to completely cut off the power.
    2. Slide the dishwasher out from its installation spot to get to the control board, usually located in the door panel or at the base.
    3. Take a clear picture of the wire connections before you start, for easy reference.
    4. Carefully unplug all the wires connected to the control board.
    5. Remove the screws that are holding the control board in place and take out the old board.
    6. Put the new control board in the same spot and secure it with the screws.
    7. Reconnect all the wires by looking at the picture you took, put the dishwasher back, and turn the power on.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00438026
    • 00622058
    • 10028963

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F31

    How to Fix Bosch Washer Error F31

    Error Code: F31 Difficulty: Easy

    Problem: Maximum water level exceeded.

    How to Fix F31 Error (Step-by-Step)

    1. Press the cancel or stop button to end the current cycle and drain the excess water.
    2. Unplug the washer from the power source and confirm the error stays cleared during a full test cycle.
    3. Check the drain hose for any clogs or kinks that might be preventing proper drainage.
    4. Locate and clean the drain pump filter, which is usually accessible through a small door on the front of the washer.
    5. If the washer is still overfilling, the pressure switch, which senses the water level, may be malfunctioning.
    6. To check the pressure switch, you will need to access it by removing a panel and inspect the hose for blockages and the switch for defects.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Refrigerator Error E01

    How to Fix Bosch Refrigerator Error E01

    Error Code: E01 Difficulty: Moderate

    Problem: Refrigerator compartment temperature sensor is faulty.

    How to Fix E01 Error (Step-by-Step)

    1. Disconnect the refrigerator from the power source for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the refrigerator compartment temperature sensor. It is typically found on the interior side wall or ceiling.
    3. Carefully remove any shelves or drawers that may be obstructing access to the sensor.
    4. Disconnect the wire harness attached to the old sensor and confirm the error stays cleared during a full test cycle.
    5. Remove the old sensor. It may be held in place by a clip or a screw.
    6. Install the new temperature sensor, ensuring it is securely in place.
    7. Reconnect the wire harness, replace any shelves or drawers, and restore power to the refrigerator.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • 00618543
    • 00625294
    • 00627548

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.