Category: Bosch

  • How to Fix Bosch Washer Error E32

    How to Fix Bosch Washer Error E32

    Error Code: E32 Difficulty: Easy

    Problem: Laundry imbalance detected.

    How to Fix E32 Error (Step-by-Step)

    1. Pause the wash cycle and open the door and confirm the error stays cleared during a full test cycle.
    2. Redistribute the laundry inside the drum more evenly. Avoid washing single, heavy items.
    3. Ensure the load is not too small or too large for the machine’s capacity.
    4. Check that the washing machine is level on the floor. Adjust the feet if necessary to prevent rocking.
    5. Close the door and resume the cycle. The machine should attempt to rebalance the load.
    6. If the error persists, stop the cycle, remove some items if overloaded, or add a few towels if underloaded to help with balance.
    7. Restart the cycle from the beginning and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E33

    How to Fix Bosch Washer Error E33

    Error Code: E33 Difficulty: Easy

    Problem: Detergent foam detected.

    How to Fix E33 Error (Step-by-Step)

    1. Pause the current washing program and confirm the error stays cleared during a full test cycle.
    2. Wait for a few minutes to allow the foam to dissipate on its own.
    3. If the foam is excessive, you may need to run a rinse and spin cycle to clear it out.
    4. Check the type and amount of detergent you are using. Ensure it is a high-efficiency (HE) detergent suitable for front-loaders.
    5. Reduce the amount of detergent used in future washes, especially for smaller or lightly soiled loads.
    6. Run an empty cleaning cycle with hot water to flush out any residual suds from the machine.
    7. Resume your normal washing, being mindful of the detergent dosage.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E34

    How to Fix Bosch Washer Error E34

    Error Code: E34 Difficulty: Moderate

    Problem: Door Not Locked Properly.

    How to Fix E34 Error (Step-by-Step)

    1. Disconnect the washer from the power source and confirm the error stays cleared during a full test cycle.
    2. Open the washing machine door and locate the door lock assembly.
    3. Use a screwdriver to remove the outer retaining band that secures the door boot seal to the front panel.
    4. Peel back the door boot seal to access the screws holding the door lock assembly in place.
    5. Remove the screws and carefully pull the door lock assembly out, disconnecting the wiring harness.
    6. Connect the new door lock assembly to the wiring harness and secure it with the screws.
    7. Reattach the door boot seal and secure it with the retaining band.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E56

    How to Fix Bosch Washer Error E56

    Error Code: E56 Difficulty: Hard

    Problem: Unexpected communication error in your washing machine.

    How to Fix E56 Error (Step-by-Step)

    1. Unplug the washing machine from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel of the washer by unscrewing the screws at the back.
    3. Locate the main control board, which is typically housed in a plastic casing.
    4. Carefully disconnect all the wire harnesses connected to the control board, taking note of their positions.
    5. Release the locking tabs or remove the screws holding the control board in place and remove the old board.
    6. Install the new main control board, ensuring it is securely fastened.
    7. Reconnect all the wire harnesses to their corresponding terminals on the new board and reassemble the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E80

    How to Fix Bosch Washer Error E80

    Error Code: E80 Difficulty: Hard

    Problem: Fault in Drive Circuit.

    How to Fix E80 Error (Step-by-Step)

    1. Disconnect the washer from its power and water supply and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel to access the motor and main control board.
    3. Inspect the wiring between the motor and the control board for any visible damage or loose connections.
    4. If the wiring is intact, proceed to replace the main control board by disconnecting the wire harnesses and removing the mounting screws.
    5. If the error persists after replacing the control board, the motor will need to be replaced. This involves removing the drive belt and the bolts securing the motor to the drum.
    6. Install the new motor, reattach the drive belt, and reconnect all wiring.
    7. Reassemble the washer and test its functionality and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F02

    How to Fix Bosch Washer Error F02

    Error Code: F02 Difficulty: Hard

    Problem: Water is not supplied.

    How to Fix F02 Error (Step-by-Step)

    1. Disconnect the washer from the power supply and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel of the washing machine and confirm the error stays cleared during a full test cycle.
    3. Locate the heating element at the bottom of the tub.
    4. Disconnect the wires from the heating element terminals and confirm the error stays cleared during a full test cycle.
    5. Loosen the nut that secures the heating element in place. This will also loosen the rubber seal.
    6. Carefully pull the old heating element out of the tub.
    7. Insert the new heating element, ensuring the rubber seal is properly seated, and tighten the nut to secure it.
    8. Reconnect the wires and replace the rear panel and confirm the error stays cleared during a full test cycle.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F04

    How to Fix Bosch Washer Error F04

    Error Code: F04 Difficulty: Hard

    Problem: Water leakage.

    How to Fix F04 Error (Step-by-Step)

    1. Disconnect the washer from the power source and water supply.
    2. Remove the top and back panels of the washing machine to access the internal components.
    3. Carefully tilt the washer to access the motor at the bottom.
    4. Locate the motor and identify the carbon brushes, which are small rectangular blocks connected to the motor with wires.
    5. Disconnect the electrical connectors from the carbon brushes and unscrew them from the motor housing.
    6. Install the new carbon brushes, ensuring they are securely fastened and the electrical connectors are reattached.
    7. Reassemble the washer by securing the back and top panels, reconnecting the power and water, and testing for proper operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F16

    How to Fix Bosch Washer Error F16

    Error Code: F16 Difficulty: Moderate

    Problem: The hatch door is not closed or is not locked properly.

    How to Fix F16 Error (Step-by-Step)

    1. Unplug the washing machine from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Open the washer door and locate the door lock assembly on the frame of the machine.
    3. Remove the outer retaining ring that secures the door boot seal to the front panel.
    4. Peel back the door boot seal around the door lock assembly to gain access to the mounting screws.
    5. Unscrew the door lock assembly from the front panel and disconnect the wiring harness.
    6. Connect the wiring harness to the new door lock assembly and mount it onto the front panel with the screws.
    7. Re-secure the door boot seal with the retaining ring, plug in the washer, and test the new door lock.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F17

    How to Fix Bosch Washer Error F17

    Error Code: F17 Difficulty: Moderate

    Problem: Time of water intake exceeded; water supply error.

    How to Fix F17 Error (Step-by-Step)

    1. Turn off the water supply to the washing machine and unplug it from the power source.
    2. Pull the washer away from the wall to access the back panel.
    3. Locate the water inlet valve where the water hoses connect to the machine.
    4. Disconnect the hoses from the inlet valve, being prepared for some residual water to spill.
    5. Remove the screws holding the inlet valve in place and disconnect the wiring harnesses.
    6. Install the new water inlet valve, reconnecting the wiring and securing it with the screws.
    7. Reattach the water hoses, turn the water supply back on, plug in the washer, and check for leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error F19

    How to Fix Bosch Washer Error F19

    Error Code: F19 Difficulty: Hard

    Problem: Water heating time exceeded.

    How to Fix F19 Error (Step-by-Step)

    1. Unplug the washing machine from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the back panel of the washer to access the heating element, which is located at the bottom of the tub.
    3. Disconnect the wires from the heating element terminals and confirm the error stays cleared during a full test cycle.
    4. Loosen the nut that secures the heating element in place, but do not remove it completely.
    5. Gently pry the old heating element out of the tub. This may require some force if it is sealed tightly.
    6. Insert the new heating element into the tub, ensuring the rubber seal is properly seated. Tighten the retaining nut and reconnect the wires.
    7. Reattach the back panel, plug in the washer, and run a hot water cycle to test the new element.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Heating Element

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.