Category: Dryer

Error Code: E04 Difficulty: Easy

Problem: Overloading of the dryer.

How to Fix E04 Error (Step-by-Step)

1. This error indicates that the dryer drum is too full for the clothes to tumble properly.
2. Press the ‘Start/Stop’ button to pause the current cycle.
3. Open the dryer door and remove approximately one-third to one-half of the laundry.
4. The remaining clothes should have plenty of space to move and fall freely within the drum.
5. Close the dryer door securely and confirm the error stays cleared during a full test cycle.
6. Press the ‘Start/Stop’ button again to resume the cycle with the smaller load.
7. You will need to dry the items you removed in a separate load.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: CUPBOARD DRY SYMBOL Difficulty: Easy

Problem: Indicates that the ‘Cupboard Dry’ cycle is in progress, meaning laundry will be dry enough to store.

How to Fix CUPBOARD DRY SYMBOL Error (Step-by-Step)

1. This symbol is not an error, but an indicator of the selected drying program.
2. ‘Cupboard Dry’ is a standard setting for cottons and linens.
3. It is designed to dry the laundry to a level where it can be immediately folded and stored in a cupboard.
4. No action is needed. The dryer is functioning as intended for the selected cycle.
5. If your clothes are not as dry as you would like, you can select a more intensive drying level next time, such as ‘Cupboard Dry Plus’.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: CROSSED OUT SQUARE WITH CIRCLE Difficulty: Easy

Problem: Do not tumble dry.

How to Fix CROSSED OUT SQUARE WITH CIRCLE Error (Step-by-Step)

1. This symbol is found on clothing care labels, not on the dryer itself.
2. It is an instruction from the clothing manufacturer that means ‘Do Not Tumble Dry’.
3. If you see this symbol on a garment, you should remove it from the dryer immediately to prevent damage.
4. Drying this item can cause it to shrink, warp, or otherwise be ruined.
5. Find an alternative way to dry the item, such as hanging it on a line or laying it flat.
6. Always check the care labels on your laundry before placing them in the dryer.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: CONDENSATE CONTAINER FULL SYMBOL Difficulty: Easy

Problem: The water collection container needs to be emptied.

How to Fix CONDENSATE CONTAINER FULL SYMBOL Error (Step-by-Step)

1. Pause the drying cycle if it is running and confirm the error stays cleared during a full test cycle.
2. Locate the condensate water container, which is typically on the top left of the dryer.
3. Slowly and carefully slide the container all the way out of the dryer.
4. Carry the container upright to a sink or drain to avoid spilling.
5. Pour out all the collected water from the container and confirm the error stays cleared during a full test cycle.
6. Firmly slide the empty container back into its slot until it clicks into place.
7. You can now resume the drying cycle and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: CLN Difficulty: Easy

Problem: The heat exchanger is undergoing an automatic self-cleaning cycle.

How to Fix CLN Error (Step-by-Step)

1. This symbol indicates that the dryer’s automatic self-cleaning cycle for the heat exchanger is active.
2. No action is required from you. This is a normal maintenance function.
3. The cleaning process will run automatically during the drying cycle.
4. Do not interrupt the drying cycle or turn off the power while this is in progress.
5. The ‘CLN’ indicator will disappear once the self-cleaning process is complete.
6. You can continue to use your dryer as normal and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: CLEAN FILTER SYMBOL Difficulty: Easy

Problem: The lint filter needs to be cleaned.

How to Fix CLEAN FILTER SYMBOL Error (Step-by-Step)

1. Open the dryer door and locate the lint filter, which is usually just inside the opening.
2. Pull the lint filter straight up and out of its housing.
3. Open the filter screen and use your fingers to peel off the layer of lint.
4. For a more thorough cleaning, you can wash the filter with warm, soapy water and a soft brush.
5. Ensure the filter is completely dry before reinserting it and confirm the error stays cleared during a full test cycle.
6. Slide the clean, dry filter back into its housing until it clicks firmly into place.
7. It is important to do this after every load to ensure proper airflow and drying efficiency.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: ANTI-CREASE SYMBOL Difficulty: Easy

Problem: The anti-crease function is activated.

How to Fix ANTI-CREASE SYMBOL Error (Step-by-Step)

1. Do not be alarmed, this is a normal function of your dryer.
2. The Anti-Crease cycle tumbles the clothes periodically without heat after the main drying cycle is complete.
3. This feature prevents deep wrinkles from setting in if you cannot unload the laundry immediately.
4. To stop the Anti-Crease function, simply open the dryer door.
5. You can also turn the program selector dial to the ‘Off’ position.
6. Unload your laundry as you normally would and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes

Error Code: E27 Difficulty: Moderate

Problem: Control module failure; Fault with the dryer’s electronic components

How to Fix E27 Error (Step-by-Step)

1. Turn the dryer off, unplug it from the power source, wait for a few minutes, and then plug it back in to reset the electronics.
2. If the error persists after a power cycle, professional service is required to diagnose and replace the control module.
3. Turn the appliance off, wait about 2 minutes, then turn it back on.
4. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
5. Make sure all doors, lids, and hoses are fully closed and seated correctly.
6. Run a short test cycle to see if the error clears.
7. Stop the cycle if the same error comes back right away, and avoid repeated restarts.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E26 Difficulty: Moderate

Problem: Control module failure; Fault with the dryer’s electronic components

How to Fix E26 Error (Step-by-Step)

1. Turn the dryer off, unplug it from the power source, wait for a few minutes, and then plug it back in to reset the electronics.
2. If the error persists after a power cycle, professional service is required to diagnose and replace the control module.
3. Turn the appliance off, wait about 2 minutes, then turn it back on.
4. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
5. Make sure all doors, lids, and hoses are fully closed and seated correctly.
6. Run a short test cycle to see if the error clears.
7. Stop the cycle if the same error comes back right away, and avoid repeated restarts.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E25 Difficulty: Moderate

Problem: Control module failure; Fault with the dryer’s electronic components

How to Fix E25 Error (Step-by-Step)

1. Turn the dryer off, unplug it from the power source, wait for a few minutes, and then plug it back in to reset the electronics.
2. If the error persists after a power cycle, professional service is required to diagnose and replace the control module.
3. Turn the appliance off, wait about 2 minutes, then turn it back on.
4. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
5. Make sure all doors, lids, and hoses are fully closed and seated correctly.
6. Run a short test cycle to see if the error clears.
7. Stop the cycle if the same error comes back right away, and avoid repeated restarts.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.