Category: Dryer

Error Code: F50 Difficulty: Moderate

Problem: General error requiring a power cycle.

How to Fix F50 Error (Step-by-Step)

1. First, perform a power cycle by unplugging your dryer from the wall outlet.
2. Wait for at least 5 minutes to allow the internal electronics to fully reset.
3. Plug the dryer back into the outlet and attempt to start a cycle.
4. If the code reappears, unplug the dryer again and remove the rear service panel to access the thermal fuse, which is a small, white, non-resettable fuse on the blower housing.
5. Use a multimeter to test the thermal fuse for continuity. If the multimeter does not show a continuous electrical path, the fuse has blown and needs to be replaced.
6. If the thermal fuse is good, the issue may be with the main control board, which requires professional replacement.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F5E1 Difficulty: Moderate

Problem: A problem with the door switch has been detected.

How to Fix F5E1 Error (Step-by-Step)

1. Disconnect the dryer from the power source completely and confirm the error stays cleared during a full test cycle.
2. Open the dryer door and locate the door switch, typically found along the frame where the door closes.
3. Remove the screws holding the switch in place. You may need to use a putty knife to gently pry open the top or front panel to gain access.
4. Carefully pull the switch out and disconnect the wire harness attached to it.
5. Test the old switch with a multimeter. When the actuator button is pressed, you should have continuity across the terminals. If not, the switch is faulty.
6. Connect the new door switch to the wire harness, secure it in its housing with the screws, and reassemble any panels you removed.
7. Reconnect power and test the dryer and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F5E3 Difficulty: Moderate

Problem: Latch circuit failure.

How to Fix F5E3 Error (Step-by-Step)

1. Unplug the dryer from the electrical outlet to ensure safety.
2. Open the dryer door to inspect the door latch mechanism, which includes the catch on the door and the strike on the dryer body.
3. Check for any visible damage, wear, or debris that might be preventing the latch from engaging correctly.
4. To replace the latch, you will typically need to remove the screws holding the inner door panel to access the door catch assembly.
5. Remove the old catch and strike. The kit often includes several latch and strike options; match the new parts to your old ones.
6. Install the new door catch on the door and the new strike on the dryer frame, ensuring they are aligned properly.
7. Close the door to test if it latches securely before plugging the dryer back in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F5E4 Difficulty: Easy

Problem: Indicates that the door was not opened for 3 consecutive cycles.

How to Fix F5E4 Error (Step-by-Step)

1. This code indicates the dryer’s control board has not detected the door being opened for three straight cycles.
2. Simply open the dryer door fully and confirm the error stays cleared during a full test cycle.
3. Close the dryer door firmly, ensuring you hear a ‘click’ to indicate the latch has engaged.
4. If the code persists after opening and closing the door, inspect the door latch and switch for any signs of damage or obstruction.
5. Ensure the door is not sagging and that the latch aligns properly with the door strike on the dryer frame.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F6E3 Difficulty: Hard

Problem: Indicates an issue with the appliance control unit, user interface, or associated wiring.

How to Fix F6E3 Error (Step-by-Step)

1. Turn off the circuit breaker for the dryer or unplug it from the wall.
2. Disassemble the control console area to get access to the user interface board.
3. Remove the main service panel to locate the appliance control unit (main board).
4. Visually inspect the wires that connect these two boards. Ensure the connectors are fully plugged in and that no wires are cut, burnt, or pinched.
5. Reseat the connectors by unplugging them and plugging them back in firmly.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F70 Difficulty: Hard

Problem: Communication failure between the user interface board and the main control board.

How to Fix F70 Error (Step-by-Step)

1. Begin by completely disconnecting the dryer from its power supply.
2. Remove the necessary panels to access both the main control board and the user interface board in the console.
3. Locate the communication cable that links the two boards and confirm the error stays cleared during a full test cycle.
4. Carefully check the entire length of the cable for any visible signs of damage, like cuts or abrasions.
5. Disconnect the cable from both the main board and the user interface board, then reconnect it, making sure the connections are secure and tight.
6. If the error persists after checking the wiring, it signifies a critical failure in one of the boards, which will need to be professionally diagnosed and replaced.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F7E1 Difficulty: Easy

Problem: Motor speed sensing error; the motor is not reaching the correct speed for the selected cycle.

How to Fix F7E1 Error (Step-by-Step)

1. Open the dryer door and check the load size. An overly large or heavy load can prevent the drum from spinning up to the correct speed.
2. Untangle and redistribute the items inside the drum to ensure the load is balanced.
3. Remove any items if the dryer is overloaded, then close the door firmly.
4. Select a new cycle and press the ‘Start’ button and confirm the error stays cleared during a full test cycle.
5. Turn the appliance off, wait about 2 minutes, then turn it back on.
6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: F9E2 Difficulty: Easy

Problem: Drain assembly failure. This indicates that the float switch is in the full position and the pump has been on for more than 60 seconds.

How to Fix F9E2 Error (Step-by-Step)

1. Press the ‘Power’ button to cancel the cycle and stop the pump.
2. Prepare for water drainage by placing towels and a shallow pan under the drain pump filter access door, typically located at the bottom-front of the unit.
3. Open the access door and slowly twist the filter cap counter-clockwise to allow the trapped water to drain into the pan.
4. Once all water has drained, completely remove the filter and confirm the error stays cleared during a full test cycle.
5. Clean the filter thoroughly by removing any lint, coins, or other debris under running water.
6. Check inside the filter housing for any obstructions and clear them out.
7. Securely screw the clean filter back in place, restore power, and run a drain/spin cycle to confirm the issue is resolved.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: FD Difficulty: Easy

Problem: On some washer/dryer combo units, this indicates a drainage fault or a heating issue. On standalone washers, it means “Factory Default” settings have been restored.

How to Fix FD Error (Step-by-Step)

1. Press the ‘Cancel’ button to clear the code. This error indicates a drainage issue on washer/dryer combo units.
2. Check the drain hose at the back of the appliance. Ensure it is not kinked, crushed, or clogged.
3. Verify that the end of the drain hose is not sealed into the standpipe; there should be an air gap to allow for proper draining.
4. Confirm that the standpipe or utility sink where the unit drains is not clogged.
5. Locate the drain pump filter access panel on the bottom front of the unit. Place a towel down and unscrew the filter to clean out any accumulated lint or debris.
6. Reinstall the filter securely and run a test cycle to see if the error is cleared.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: PF Difficulty: Moderate

Problem: A power failure has occurred, interrupting the drying cycle.

How to Fix PF Error (Step-by-Step)

1. The ‘PF’ code simply indicates the dryer cycle was interrupted by a power failure. Press the ‘Start’ button to clear the code and resume the cycle.
2. If there was no known power outage and the code appears, unplug the dryer from the wall outlet.
3. Wait for at least 10 minutes to allow the internal electronics to fully discharge and reset.
4. While unplugged, inspect the power cord for any signs of damage or a loose connection at the terminal block on the back of the dryer.
5. Plug the dryer securely back into the outlet and attempt to start a new cycle.
6. If the code persists or the dryer behaves erratically, a power surge may have damaged the main electronic control board, which will require professional diagnosis and replacement.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes