Author: ApplianceFixGuide Team

  • How to Fix Amana Dishwasher Error 6-6

    How to Fix Amana Dishwasher Error 6-6

    Error Code: 6-6 Difficulty: Easy

    Problem: Incoming water is too cool.

    How to Fix 6-6 Error (Step-by-Step)

    1. Before starting a dishwasher cycle, run the hot water at the kitchen sink faucet for a minute or two until the water is hot to the touch.
    2. This purges the cold water from the hot water line, ensuring that your dishwasher starts its cycle with hot water immediately.
    3. Check the temperature setting on your home’s water heater. For best dishwasher performance, it should be set to at least 120°F (49°C).
    4. Avoid running other hot water appliances, like a washing machine or shower, at the same time as the dishwasher to ensure an adequate supply of hot water.
    5. If your dishwasher has a ‘High-Temp Wash’ or ‘Sani-Rinse’ option, select it. This uses the dishwasher’s internal heater to boost the water temperature to the required level.
    6. If the problem continues, the dishwasher’s internal water heater or thermostat may be malfunctioning, which would require a more technical repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 7-1

    How to Fix Amana Dishwasher Error 7-1

    Error Code: 7-1 Difficulty: Hard

    Problem: No heat – heater circuit problem.

    How to Fix 7-1 Error (Step-by-Step)

    1. Disconnect Power: Turn off the circuit breaker for the dishwasher to ensure safety.
    2. Access the Heater: Remove the lower access panel and toe plate at the bottom front of the dishwasher.
    3. Disconnect Wires: Locate the heating element terminals at the front of the dishwasher’s tub. Carefully disconnect the two wires attached to it.
    4. Remove Old Element: Open the dishwasher door and remove the lower dish rack. Unscrew the plastic nuts holding the old heating element in place from inside the tub.
    5. Install New Element: Place the new heating element (Part No. W10518394) into the tub, ensuring the rubber washers are properly seated. Secure it with the nuts from inside the tub.
    6. Reconnect and Reassemble: Reconnect the wires to the new element’s terminals. Replace the lower access panel and toe plate.
    7. Restore Power: Turn the circuit breaker back on and run a test cycle to confirm the water is heating.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 7-2

    How to Fix Amana Dishwasher Error 7-2

    Error Code: 7-2 Difficulty: Hard

    Problem: Heater stuck on.

    How to Fix 7-2 Error (Step-by-Step)

    1. Disconnect Power: Completely disconnect the dishwasher from its power source by shutting off the corresponding circuit breaker.
    2. Access Control Board: The main control board is usually located inside the dishwasher’s door panel. Remove the screws holding the inner door panel to access it.
    3. Disconnect Wiring: Take a clear photo of the wire connections for reference. Carefully disconnect all wire harnesses from the old control board.
    4. Remove Old Board: Unclip or unscrew the old control board (Part No. WPW10285180 or W11413274) from its mounting bracket.
    5. Install New Board: Mount the new control board in the same position. Reconnect all wire harnesses by referring to the photo you took.
    6. Reassemble Door: Secure the inner door panel with the screws you removed earlier.
    7. Restore Power: Turn the power back on at the circuit breaker and test the dishwasher’s functions.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10285180

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 8-1

    How to Fix Amana Dishwasher Error 8-1

    Error Code: 8-1 Difficulty: Hard

    Problem: Slow drain.

    How to Fix 8-1 Error (Step-by-Step)

    1. Disconnect Power and Water: Shut off the power to the dishwasher at the circuit breaker and turn off the water supply valve, usually located under the sink.
    2. Check for Simple Clogs: Remove and clean the dishwasher’s filter at the bottom of the tub. Check the drain hose for any visible kinks or blockages.
    3. Access the Drain Pump: Remove the lower access panel. The drain pump (Part No. W11087376) is located at the bottom of the dishwasher.
    4. Disconnect the Old Pump: Place a towel under the pump to catch any residual water. Disconnect the wire harness and the hoses from the pump.
    5. Remove Old Pump: Unclip or unscrew the old drain pump from its housing and remove it.
    6. Install New Pump: Mount the new drain pump in place and reconnect the hoses and the electrical connector.
    7. Reassemble and Test: Reattach the access panel, restore power and water, and run a drain cycle to check for leaks and proper function.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 8-2

    How to Fix Amana Dishwasher Error 8-2

    Error Code: 8-2 Difficulty: Hard

    Problem: Drain motor electrical problem.

    How to Fix 8-2 Error (Step-by-Step)

    1. Turn Off Power: For your safety, disconnect the dishwasher from the power supply by switching off the circuit breaker.
    2. Access the Pump: Remove the bottom front toe and access panels of the dishwasher to get to the components underneath.
    3. Locate Drain Pump: Find the drain pump (Part No. W11087376). It will have a wire harness and two hoses connected to it.
    4. Disconnect Old Pump: Place a shallow pan and towel underneath to catch water. Carefully disconnect the wire harness and then the hoses from the pump.
    5. Remove and Replace: Unmount the old pump from the dishwasher base. Install the new pump, ensuring it is securely mounted.
    6. Reconnect Everything: Attach the hoses and the wire harness to the new pump. Ensure all connections are tight to prevent leaks.
    7. Final Steps: Reinstall the access panels, turn the power back on, and run a test cycle to ensure the new pump operates correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 8-3

    How to Fix Amana Dishwasher Error 8-3

    Error Code: 8-3 Difficulty: Hard

    Problem: Drain stuck on.

    How to Fix 8-3 Error (Step-by-Step)

    1. Shut Off Power: Go to your home’s circuit breaker panel and turn off the power to the dishwasher.
    2. Open the Door Panel: The control board is located inside the door. You will need to remove the series of screws around the perimeter of the inner door panel to separate it from the outer panel.
    3. Locate the Control Board: With the panel open, you will see the main control board (Part No. WPW10285180 or W11413274) in a plastic housing.
    4. Swap the Boards: Take a picture of the wiring for reference. Carefully disconnect all the wire connectors from the old board. Unclip it from its housing and install the new board.
    5. Reconnect Wires: Using your photo as a guide, plug all the wire harnesses into the correct ports on the new control board.
    6. Reassemble and Test: Put the inner door panel back on and secure it with the screws. Restore power at the breaker and run a cycle to confirm the repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10285180

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 9-1

    How to Fix Amana Dishwasher Error 9-1

    Error Code: 9-1 Difficulty: Hard

    Problem: Faulty Control Motor Drive Circuit or Sense Circuit.

    How to Fix 9-1 Error (Step-by-Step)

    1. Disconnect Power Source: Ensure your safety by turning off the circuit breaker that supplies power to the dishwasher.
    2. Access the Control Board: Remove the screws holding the inner door panel in place. This will give you access to the dishwasher’s electronic components.
    3. Identify the Board: Locate the main control board (Part No. WPW10285180 or W11413274). It is the central hub for all the wiring.
    4. Photograph and Disconnect: Before disconnecting anything, take a clear picture of the wire layout. Then, carefully unplug all the wire harnesses from the board.
    5. Replace the Board: Release any clips or screws holding the old board and remove it. Snap or screw the new control board into the same location.
    6. Reconnect and Reassemble: Following your reference photo, reconnect all the wire harnesses to the new board. Secure the inner door panel back onto the dishwasher.
    7. Power Up: Turn the circuit breaker back on and start a new cycle to verify that the dishwasher is functioning correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10285180

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 9-2

    How to Fix Amana Dishwasher Error 9-2

    Error Code: 9-2 Difficulty: Hard

    Problem: Faulty Control Motor Drive Circuit or Sense Circuit.

    How to Fix 9-2 Error (Step-by-Step)

    1. Disconnect Power Source: Ensure your safety by turning off the circuit breaker that supplies power to the dishwasher.
    2. Access the Control Board: Remove the screws holding the inner door panel in place. This will give you access to the dishwasher’s electronic components.
    3. Identify the Board: Locate the main control board (Part No. WPW10285180 or W11413274). It is the central hub for all the wiring.
    4. Photograph and Disconnect: Before disconnecting anything, take a clear picture of the wire layout. Then, carefully unplug all the wire harnesses from the board.
    5. Replace the Board: Release any clips or screws holding the old board and remove it. Snap or screw the new control board into the same location.
    6. Reconnect and Reassemble: Following your reference photo, reconnect all the wire harnesses to the new board. Secure the inner door panel back onto the dishwasher.
    7. Power Up: Turn the circuit breaker back on and start a new cycle to verify that the dishwasher is functioning correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10285180

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error ALL CYCLE AND OPTION LIGHTS FLASHING

    How to Fix Amana Dishwasher Error ALL CYCLE AND OPTION LIGHTS FLASHING

    Error Code: ALL CYCLE AND OPTION LIGHTS FLASHING Difficulty: Easy

    Problem: The cycle has been suspended, usually because the door was opened during operation.

    How to Fix ALL CYCLE AND OPTION LIGHTS FLASHING Error (Step-by-Step)

    1. Close the Door: This error typically means the cycle was interrupted. Ensure the dishwasher door is firmly closed and latched.
    2. Press the Start/Resume Button: Press the ‘Start/Resume’ button one time to continue the cycle from where it left off.
    3. Select a New Cycle (If Needed): If pressing ‘Start/Resume’ does not work, press the ‘Cancel’ button to drain the unit. You can then select a new wash cycle.
    4. Check for Obstructions: Make sure no dishes are blocking the door from closing properly or interfering with the detergent dispenser.
    5. Power Cycle the Dishwasher: If the lights continue to flash, turn off the power to the dishwasher at the circuit breaker for one minute, then turn it back on to reset the control panel.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error ALL CYCLE AND OPTION LIGHTS FLASHING

    How to Fix Amana Dishwasher Error ALL CYCLE AND OPTION LIGHTS FLASHING

    Error Code: ALL CYCLE AND OPTION LIGHTS FLASHING Difficulty: Easy

    Problem: The cycle is suspended because the door was opened.

    How to Fix ALL CYCLE AND OPTION LIGHTS FLASHING Error (Step-by-Step)

    1. Close the dishwasher door firmly and confirm the error stays cleared during a full test cycle.
    2. The dishwasher pauses the cycle when the door is opened mid-cycle.
    3. Once the door is securely latched, the cycle will automatically resume.
    4. If the cycle does not resume, press the START/RESUME button.
    5. Ensure no dishes are blocking the door from closing completely.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes