Author: ApplianceFixGuide Team

How to Fix Samsung Dishwasher Error 4E
Problem: Water inlet valve failure; solenoid coil open/shorted or mechanical valve fault

How to Fix Dishwasher Error
1. Unplug dishwasher and turn off water supply valve.
2. Remove lower access panel to expose inlet valve assembly.
3. Disconnect water supply hose from valve inlet (place towel underneath).
4. Disconnect electrical wiring harness from valve solenoid.
5. Test solenoid coil resistance with multimeter: proper reading 500-1500Ω. Infinite = open; zero = shorted.
6. Remove mounting screws securing valve assembly to chassis.
7. Extract old inlet valve assembly. Clean mounting area of mineral deposits.
8. Install new inlet valve assembly using OEM part DD61-00001A. Secure mounting screws.
9. Reconnect water supply hose hand-tight plus 1/4 turn. Reconnect wiring harness.
10. Restore water and power. Start cycle and verify dishwasher fills within 60 seconds with strong flow.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 5C
Problem: Drain filter clogged; debris blocking coarse filter assembly

How to Fix Dishwasher Error
1. Unplug dishwasher and open door.
2. Remove lower dish rack to access filter assembly at bottom of tub.
3. Rotate coarse filter counterclockwise 1/4 turn and lift out.
4. Remove fine mesh filter underneath by lifting straight up.
5. Rinse both filters thoroughly under running water. Use soft brush to remove stuck food particles and grease buildup.
6. Inspect filter housing cavity for debris. Wipe clean with damp cloth.
7. Reinstall fine mesh filter first, ensuring tabs seat in slots.
8. Reinstall coarse filter by aligning tabs, pressing down, and rotating clockwise until locked.
9. Close door. Restore power. Run Quick cycle to verify proper drainage and error clearance.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 5E
Problem: Drain pump failure; seized impeller, motor fault, or electrical open circuit

How to Fix Dishwasher Error
1. Unplug dishwasher and turn off water supply.
2. Remove lower access panel to expose drain pump assembly.
3. Place towels under pump area. Open pump access cover to drain residual water.
4. Remove coarse filter to access pump impeller. Rotate impeller manually with finger—it must spin freely 360°.
5. If impeller is stuck, cracked, or pump housing is damaged: disconnect pump wiring harness.
6. Loosen hose clamps on inlet/outlet hoses using pliers. Remove mounting screws securing pump.
7. Extract old drain pump assembly. Clean mounting surface thoroughly.
8. Install new drain pump using OEM part DD31-00010A. Align mounting tabs, secure screws.
9. Reconnect hoses with clamps tightened firmly. Reconnect wiring harness.
10. Reinstall filter and access cover. Restore power. Run Drain cycle to verify complete water removal within 90 seconds.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 6C
Problem: Turbidity sensor dirty; optical window obscured by grease or mineral deposits

How to Fix Dishwasher Error
1. Unplug dishwasher and open door.
2. Locate turbidity sensor window on right side wall of tub (near bottom, behind lower rack).
3. Dip soft cloth in isopropyl alcohol. Gently wipe sensor window in circular motion to remove film.
4. Use cotton swab dipped in alcohol to clean edges and crevices of sensor housing.
5. Rinse area with damp cloth to remove alcohol residue.
6. Inspect sensor window for cracks or cloudiness. Replace if physically damaged.
7. Close door. Restore power.
8. Run Sensor Clean cycle (if available) or Normal cycle with empty dishwasher.
9. Verify error clears and Auto cycle functions correctly with subsequent loads.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 6E
Problem: Turbidity sensor fault; internal sensor failure or wiring harness damage

How to Fix Dishwasher Error
1. Unplug dishwasher from electrical power.
2. Remove lower access panel to access sensor wiring harness connection.
3. Disconnect wiring harness from turbidity sensor assembly.
4. Test sensor continuity per service manual specifications using multimeter (typically checks optical circuit).
5. Inspect wiring harness for cuts, pinches, or corrosion near tub movement points.
6. If sensor tests faulty or wiring is damaged: remove mounting screw securing sensor housing.
7. Gently extract sensor assembly from tub wall. Clean mounting area thoroughly.
8. Install new turbidity sensor using OEM part DD31-00007A. Ensure O-ring is properly seated.
9. Secure mounting screw to 3 in-lbs torque. Reconnect wiring harness firmly.
10. Reinstall access panel. Restore power. Run diagnostic cycle to verify sensor communication and error clearance.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 7E
Problem: Communication error between main control board and display interface board

How to Fix Dishwasher Error
1. Unplug dishwasher for 10 minutes to reset electronics.
2. Remove top panel and control console assembly to access ribbon cable connections.
3. Disconnect ribbon cable from both display board and main control board.
4. Clean all connector pins with electrical contact cleaner and lint-free swab. Allow 5 minutes drying time.
5. Inspect ribbon cable for creases, tears, or damaged traces. Replace cable if visible damage exists.
6. Reconnect ribbon cable firmly at both ends until seated completely.
7. If error persists: replace main control board using OEM part DD92-00001A.
8. Transfer all connectors to new board one-by-one. Secure mounting screws to 4 in-lbs torque.
9. Restore power. Enter diagnostic mode (press Temp+Delay Start+Power) to verify communication with display and clear error history.
10. Run full diagnostic test sequence to confirm all subsystems operate correctly.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 8E
Problem: EEPROM memory error; corrupted firmware or processor fault on main control board

How to Fix Dishwasher Error
1. Unplug dishwasher from electrical power for 15 minutes to attempt deep reset.
2. Restore power and observe if error clears during startup sequence.
3. If persistent, remove lower access panel to expose main control board.
4. Inspect board for burnt components, bulging capacitors, or charred traces near memory chips.
5. Check all board mounting screws and ground connections for tightness and corrosion.
6. Reseat all wiring harness connectors on main board. Clean pins with contact cleaner.
7. If visual inspection shows damage or error remains: replace main control board using OEM part DD92-00001A.
8. Transfer all connectors carefully to new board. Secure mounting hardware.
9. Restore power. Enter service mode per model instructions to initialize board memory.
10. Run full system diagnostic to verify all functions operate correctly and error history is cleared.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error 9E
Problem: Heater relay fault; relay stuck open/closed or control board circuit failure

How to Fix Dishwasher Error
1. Unplug dishwasher and allow 30 minutes for components to cool.
2. Remove lower access panel to access main control board and heater assembly.
3. Disconnect wiring harness from heater terminals. Label connections.
4. Test heater element resistance: proper reading 15-30Ω. Replace heater if open/shorted (separate procedure).
5. If heater tests good, inspect main control board near heater relay for burnt contacts or damaged traces.
6. Test relay operation per service manual using multimeter during simulated heat cycle.
7. If relay is faulty or board shows damage: replace main control board using OEM part DD92-00001A.
8. Transfer all connectors to new board one-by-one. Secure mounting screws to 4 in-lbs torque.
9. Reconnect heater wiring. Reinstall access panel.
10. Restore power. Run Sanitize cycle while monitoring water temperature with external thermometer (should reach 155°F).
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error AE
Problem: Alternate leakage error; moisture sensor activated (regional variant of 3E)

How to Fix Dishwasher Error
1. Immediately unplug dishwasher and shut off water supply valve.
2. Remove all standing water from base pan using towels or wet/dry vacuum.
3. Tilt dishwasher forward carefully (with assistance) to access underside. Locate moisture sensor pad.
4. Dry sensor pad completely with absorbent cloth. Allow full 60 minutes air drying time.
5. Inspect door gasket thoroughly for tears, cracks, or food debris. Clean gasket groove with vinegar solution.
6. Check detergent dispenser gasket and spray arm seals for leaks. Tighten any loose components.
7. If sensor remains triggered after drying: replace moisture sensor using OEM part DD31-00005A.
8. Reassemble all panels securely.
9. Restore water and power. Run short Rinse cycle with panels off to visually confirm no leaks.
10. Monitor for 15 minutes after cycle completion to ensure no residual moisture triggers sensor.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026
How to Fix Samsung Dishwasher Error bE
Problem: Control panel button error; stuck key, shorted membrane, or ribbon cable fault

How to Fix Dishwasher Error
1. Unplug dishwasher from electrical power.
2. Press each button on control panel firmly 5 times to dislodge debris or contaminants.
3. Remove control console assembly: release retaining clips or remove screws, carefully disconnect ribbon cable.
4. Inspect ribbon cable and connectors for moisture, corrosion, or physical damage. Clean contacts with isopropyl alcohol.
5. Test button matrix continuity using multimeter per service manual pinout diagram.
6. If short circuit persists after cleaning, or ribbon cable is damaged: replace control panel assembly using OEM part DD92-00002A.
7. Transfer all connectors to new panel. Secure mounting hardware.
8. Reconnect ribbon cable firmly until seated completely.
9. Reinstall console assembly. Restore power.
10. Verify all buttons respond correctly during operation and error code does not reappear.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
February 28, 2026