Author: ApplianceFixGuide Team

  • How to Fix Samsung Refrigerator Error 84C

    How to Fix Samsung Refrigerator Error 84C

    Problem: Compressor locked – motor locked error

    How to Fix 84C Error

    1. UNPLUG THE REFRIGERATOR. This is a critical error indicating the compressor is locked or has failed.
    2. This is not a DIY repair. The compressor is part of the sealed refrigerant system.
    3. The cause can be a failed compressor, a bad inverter control board that powers the compressor, or a refrigerant leak.
    4. This requires diagnosis and repair by a certified refrigeration technician. Check your warranty, as compressors often have a 5 or 10-year warranty.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error 88 88

    How to Fix Samsung Refrigerator Error 88 88

    Problem: Communication fault – power disrupted during bootup; refrigerator did not boot properly

    How to Fix 88 88 Error

    1. This code indicates a communication fault, often after a power outage or if power was interrupted during its startup sequence.
    2. The first step is to perform a hard reset. Unplug the refrigerator or turn it off at the circuit breaker.
    3. Wait for 5-10 minutes to allow all the internal electronics to fully discharge and reset.
    4. Plug the refrigerator back in. The unit should boot up normally. If the code returns, it may indicate a failure of the main control board, which would require professional service.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error All icons flashing

    How to Fix Samsung Refrigerator Error All icons flashing

    Problem: Self-diagnostic mode after power outage or initial plug-in – normal startup behavior

    How to Fix All icons flashing Error

    1. This is not an error. It is the normal startup behavior of the refrigerator after it is first plugged in or after a power outage.
    2. The flashing indicates the refrigerator is running a self-diagnostic test.
    3. Do not press any buttons. Allow the diagnostic to complete, which usually takes a few minutes.
    4. The display will return to normal temperature readings once the test is finished.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error Ice Off blinking

    How to Fix Samsung Refrigerator Error Ice Off blinking

    Problem: Ice bucket not properly installed or missing – ice maker will not operate

    How to Fix Ice Off blinking Error

    1. This indicates that the ice maker is turned off, but also that the ice bucket is not installed correctly.
    2. Remove the ice bucket from its position.
    3. Re-install the ice bucket, making sure it is pushed all the way back and seated firmly into place. You should feel it lock or click in.
    4. The blinking light should stop, and the ice maker will resume operation (if it is turned on).

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error 1dF

    How to Fix Samsung Dryer Error 1dF

    Problem: Door error (FlexDry models)

    How to Fix 1dF Error

    1. This error is for the upper, delicate dryer on a FlexDry model. First, open and firmly close the small top door to ensure it is latched properly.
    2. Check for any lint or debris obstructing the door latch mechanism.
    3. If the error persists, the door latch/switch assembly has failed. UNPLUG THE DRYER.
    4. To access the switch, you will need to remove the top control console and/or top panel of the dryer. Disconnect the wire harness from the old switch, remove its mounting screws, and install the new one.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error 1tCS

    How to Fix Samsung Dryer Error 1tCS

    Problem: Temperature sensor fault (FlexDry models)

    How to Fix 1tCS Error

    1. This is a temperature sensor error for the upper FlexDry unit. UNPLUG THE DRYER.
    2. You will need to remove the top console and/or top panel to access the thermistor for the upper dryer.
    3. Locate the sensor, disconnect its wiring, and test its resistance with a multimeter.
    4. Like other thermistors, it should read around 10kΩ at room temperature. If the reading is bad, replace the sensor.
    5. Install the new thermistor, reconnect the wiring, and reassemble the dryer.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error 6C2

    How to Fix Samsung Dryer Error 6C2

    Problem: Button stuck on control panel

    How to Fix 6C2 Error

    1. UNPLUG THE DRYER. This error means a button on the user interface (UI) is stuck.
    2. First, try gently pressing and wiggling each button on the control panel to see if you can free the stuck one. Sometimes wiping the panel with a damp cloth can help.
    3. If that doesn’t work, the UI board is faulty and needs to be replaced. Access the board by removing the top control console panel.
    4. Disconnect the ribbon cable(s) and any other wire harnesses from the old UI board. Remove its mounting screws, install the new board, and reconnect everything.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error 6E2

    How to Fix Samsung Dryer Error 6E2

    Problem: Button stuck on control panel

    How to Fix 6E2 Error

    1. UNPLUG THE DRYER. This is an alias for 6C2, indicating a stuck button on the control panel.
    2. Try to free the stuck button by gently pressing and releasing all buttons on the panel.
    3. If the error persists, the user interface board has failed. Remove the control console to access the board.
    4. Disconnect all wiring from the old board, remove it, and install the new one. Reconnect the wiring and reassemble the console.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error 9E1

    How to Fix Samsung Dryer Error 9E1

    Problem: Abnormal voltage supply / Over voltage error

    How to Fix 9E1 Error

    1. UNPLUG THE DRYER. This error indicates the control board has detected an abnormal power supply, usually over-voltage.
    2. First, try a hard reset by leaving the dryer unplugged for 10 minutes. This can clear a temporary glitch caused by a power surge.
    3. If the error returns, and you are certain the home’s electrical supply is correct (i.e., no other appliances are affected), the main control board’s voltage detection circuit is faulty.
    4. The main control board (PBA) must be replaced. This is a complex job requiring significant disassembly to access the board, label and disconnect all wires, and install the new one.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error AC4

    How to Fix Samsung Dryer Error AC4

    Problem: Communication error between main board and Wi-Fi board

    How to Fix AC4 Error

    1. UNPLUG THE DRYER. This is a communication error between the main control board and the Wi-Fi sub-board.
    2. First, perform a hard reset by leaving the dryer unplugged for 10 minutes.
    3. If the error returns, you must access the internal electronics. Remove the top panel or console.
    4. Check the wire harness connecting the small Wi-Fi module to the main control board. Reseat the connection firmly. If the error persists, the Wi-Fi module has failed and needs to be replaced.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes