Author: ApplianceFixGuide Team

  • How to Fix Kenmore Washer Error Sud

    How to Fix Kenmore Washer Error Sud

    Problem: Excessive suds detected – improper detergent usage

    How to Fix Washer Error

    1. Pause the wash cycle immediately.
    2. Open washer door/lid and remove as much water as possible.
    3. Add 1 cup of white vinegar to help break down suds.
    4. Run a drain/spin cycle without detergent.
    5. If suds persist, repeat drain/spin cycle with cold water only.
    6. Clean detergent dispenser thoroughly with warm water.
    7. Use only HE (High Efficiency) detergent in future cycles.
    8. Reduce detergent amount to manufacturer recommendations.
    9. Check for detergent residue in dispenser housing.
    10. Run a test cycle with proper HE detergent amount to verify operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Dishwasher Error F05

    How to Fix Whirlpool Dishwasher Error F05

    Problem: Rotor Blocked / Wash Motor Fault

    How to Fix Dishwasher Error

    1. Remove filter and check for debris blocking the wash impeller.
    2. If clear, replace the wash motor assembly.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error Flash-1

    How to Fix Kenmore Dryer Error Flash-1

    Problem: Thermistor failure – temperature sensor error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Locate thermistor sensor on blower housing.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is faulty, remove mounting screws and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Reconnect electrical connector and secure mounting.
    10. Restore power and test heating cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error dE

    How to Fix Kenmore Washer Error dE

    Problem: Lid not closed – lid lock/switch assembly failure

    How to Fix Washer Error

    1. Turn off power supply.
    2. Open washer lid fully.
    3. Inspect lid lock mechanism for proper alignment.
    4. Test lid switch continuity with multimeter (should change state when lid closes).
    5. Check lid strike plate alignment with switch mechanism.
    6. Inspect lid lock wiring for damage or loose connections.
    7. If lid lock assembly is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace lid lock/switch assembly.
    9. Ensure proper alignment during installation.
    10. Test lid closure and lock function during spin cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Dishwasher Error F04

    How to Fix Whirlpool Dishwasher Error F04

    Problem: Drainage Failure

    How to Fix Dishwasher Error

    1. Check drain hose for kinks or clogs.
    2. Clean the drain filter.
    3. Check drain pump for debris.
    4. Replace drain pump if power is present but not spinning.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error FF2

    How to Fix Kenmore Dryer Error FF2

    Problem: Rear fan failure – exhaust airflow restriction

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Inspect rear blower assembly for debris or damage.
    4. Check fan motor operation and bearings for smooth rotation.
    5. Test fan motor windings with multimeter for proper resistance.
    6. Inspect fan blades for cracks, warping, or obstructions.
    7. If fan motor is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace fan motor assembly.
    9. Ensure proper alignment during installation.
    10. Test exhaust airflow and temperature distribution after repairs.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Dishwasher Error F03

    How to Fix Whirlpool Dishwasher Error F03

    Problem: Heating System Failure

    How to Fix Dishwasher Error

    1. Check the heating element for continuity (approx 10-30 ohms).
    2. Check wiring to heater.
    3. Inspect OWI (Optical Water Indicator) sensor.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error IE

    How to Fix Kenmore Washer Error IE

    Problem: Washer fills slowly – inlet valve or supply issue

    How to Fix Washer Error

    1. Turn off power and check household water supply pressure.
    2. Inspect water supply hoses for kinks or blockages.
    3. Remove lower front access panel.
    4. Check water inlet valve screens for debris or mineral buildup.
    5. Clean inlet valve filter screens with vinegar solution and soft brush.
    6. Test inlet valve solenoids with multimeter for proper operation.
    7. If valve is slow to open, replace water inlet valve assembly.
    8. Check for proper water pressure at inlet connections.
    9. Verify fill cycle timing after repairs.
    10. Test operation with different water temperature settings.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error FF1

    How to Fix Kenmore Dryer Error FF1

    Problem: Front fan failure – airflow restriction

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove front access panel.
    3. Inspect front blower assembly for debris or damage.
    4. Check fan motor operation and bearings for smooth rotation.
    5. Test fan motor windings with multimeter for proper resistance.
    6. Inspect fan blades for cracks, warping, or obstructions.
    7. If fan motor is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace fan motor assembly.
    9. Ensure proper alignment during installation.
    10. Test airflow and temperature distribution after repairs.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Dishwasher Error F02

    How to Fix Whirlpool Dishwasher Error F02

    Problem: Water Leak Detected

    How to Fix Dishwasher Error

    1. Shut off water supply.
    2. Remove kickplate and dry the base pan.
    3. Run a cycle to find the leak source (pump, hose, or seal).


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.