Author: ApplianceFixGuide Team

  • How to Fix Whirlpool Dryer Error F1E1

    How to Fix Whirlpool Dryer Error F1E1

    Problem: Stuck relay on control board

    How to Fix F1E1 Error

    1. Unplug the dryer from the wall outlet.
    2. Access the main control board, which is typically located behind the top or rear panel.
    3. Take a clear photo of all wire connections before touching anything.
    4. Carefully disconnect all wire harnesses from the old control board.
    5. Release the board from its plastic mounting tabs or screws.
    6. Install the new control board, ensuring it snaps securely into place, and reconnect all harnesses by referencing your photo.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F1E3

    How to Fix Whirlpool Dryer Error F1E3

    Problem: Console/Board Mismatch

    How to Fix F1E3 Error

    1. This error means the control board is incorrect for the dryer model or has failed. Unplug the unit.
    2. Locate the main control board, usually behind the rear panel.
    3. Verify the part number on the board matches the one specified for your dryer’s model number.
    4. If it’s the wrong part, or if it’s the correct part but has failed, replace it. Take a photo of the wires, disconnect them, swap the board, and reconnect.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F1E4

    How to Fix Whirlpool Dryer Error F1E4

    Problem: Model ID Error

    How to Fix F1E4 Error

    1. A Model ID Error points to a main control board failure. Disconnect the dryer from power.
    2. Remove the rear access panel to find the main control board.
    3. Before disconnecting anything, take a clear picture of the wire connections.
    4. Carefully unplug all harnesses from the board.
    5. Remove the old board and install the new one, ensuring it is the correct part number for your specific dryer model.
    6. Reconnect wires and reassemble.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F1E5

    How to Fix Whirlpool Dryer Error F1E5

    Problem: Control board communication error

    How to Fix F1E5 Error

    1. Unplug the dryer. This code indicates a communication failure between the two main electronic boards.
    2. Inspect the wiring harness connecting the main control board (at the back) and the user interface board (in the console). Reseat the connectors at both ends.
    3. If wiring is intact, the fault is with one of the boards. It is often recommended to replace the User Interface board first.
    4. If the error remains after replacing the UI board, the main control board will need to be replaced.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F24

    How to Fix Whirlpool Dryer Error F24

    Problem: Inlet Thermistor Open

    How to Fix F24 Error

    1. Unplug the dryer.
    2. This code indicates the inlet thermistor is ‘open’. Locate the thermistor on the blower housing or heater box.
    3. You will need to remove an access panel (usually the lower front or the rear) to see it.
    4. Disconnect the wire harness from the thermistor.
    5. Remove the screw holding it in place and install the new thermistor.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F25

    How to Fix Whirlpool Dryer Error F25

    Problem: Inlet Thermistor Shorted

    How to Fix F25 Error

    1. Unplug the dryer. This code means the inlet thermistor has shorted.
    2. Remove the lower front toe panel or the large rear panel to get access to the internal components.
    3. Find the thermistor mounted on the blower housing.
    4. Disconnect the wires and remove the mounting screw.
    5. Secure the new thermistor in place and reconnect the wiring.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F26

    How to Fix Whirlpool Dryer Error F26

    Problem: Drive Motor Failure

    How to Fix F26 Error

    1. Unplug the dryer. This is a major repair.
    2. You will need to remove the front panel and drum to access the drive motor. Start by taking off the top panel, console, and front panel.
    3. Release the tension on the drive belt from the idler pulley and remove the belt from the motor.
    4. Disconnect the motor’s wire harness and unbolt the motor from the dryer’s base.
    5. Install the new motor, re-route the belt, and carefully reassemble the dryer.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F28

    How to Fix Whirlpool Dryer Error F28

    Problem: Moisture Sensor Open

    How to Fix F28 Error

    1. Unplug the dryer.
    2. First, locate the two metal moisture sensor strips inside the drum, usually below the door opening on the lint filter housing.
    3. Clean the surface of these strips thoroughly with a cotton ball and rubbing alcohol to remove any fabric softener residue.
    4. If cleaning does not work, inspect the wires running from the sensor bars to the main harness. If the wires are intact, the sensor/harness assembly needs to be replaced.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F29

    How to Fix Whirlpool Dryer Error F29

    Problem: Moisture Sensor Shorted

    How to Fix F29 Error

    1. Unplug the dryer. A shorted sensor is often caused by residue buildup.
    2. Find the two parallel metal bars of the moisture sensor inside the drum, typically part of the lint screen housing.
    3. Vigorously clean the metal bars with a cloth or pad and rubbing alcohol.
    4. If the code persists after cleaning, the moisture sensor harness assembly is likely faulty and needs to be replaced. This may require removing the front panel for access.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F2E2

    How to Fix Whirlpool Dryer Error F2E2

    Problem: User interface / control board communication fault

    How to Fix F2E2 Error

    1. Unplug the dryer.
    2. Access the main control and user interface boards by removing the top and/or rear panels.
    3. Carefully inspect the wire harness that runs between the two boards. Look for any loose plugs, pinched wires, or signs of corrosion on the pins.
    4. If the harness looks damaged, replace it. If the harness appears fine, the User Interface board is the most likely faulty part.
    5. Replace the User Interface board, ensuring all connections are secure.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes