Author: ApplianceFixGuide Team

  • How to Fix Kenmore Dishwasher Error 8-2

    How to Fix Kenmore Dishwasher Error 8-2

    Problem: Drain pump electrical problem

    How to Fix 8-2 Error

    1. Disconnect the dishwasher from power.
    2. Remove the lower access panel and toe kick to access the drain pump.
    3. Check the drain pump’s wire harness for a secure connection and any signs of damage.
    4. If wiring is intact, use a multimeter to test the pump motor for continuity. An open circuit indicates a failed motor.
    5. If the motor is faulty, disconnect the drain hoses, remove the pump from its housing, and install the new drain pump.
    6. Reconnect hoses and wiring, then restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error 9-2

    How to Fix Kenmore Dishwasher Error 9-2

    Problem: Diverter motor stuck on

    How to Fix 9-2 Error

    1. This error indicates the diverter motor is stuck on, which is usually caused by a failed relay on the main control board.
    2. Shut off power to the dishwasher at the circuit breaker.
    3. Locate and access the main electronic control board.
    4. Carefully disconnect all wire harnesses and replace the old board with the new one.
    5. Reassemble the dishwasher and restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error 9-3

    How to Fix Kenmore Dishwasher Error 9-3

    Problem: Diverter disc is missing

    How to Fix 9-3 Error

    1. Disconnect power to the dishwasher.
    2. This repair requires accessing the sump assembly at the bottom of the dishwasher tub.
    3. Remove the lower dish rack, spray arm, and filter assembly to expose the sump.
    4. The diverter motor and disc are located within this assembly. You will need to disassemble the sump to access the diverter.
    5. If the disc is missing, a new one must be installed. This part number can vary, so it’s best to find it based on your dishwasher’s model number.
    6. Reassemble the sump, filters, and spray arm, then restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error 9-4

    How to Fix Kenmore Dishwasher Error 9-4

    Problem: Lower spray arm error

    How to Fix 9-4 Error

    1. Disconnect power to the dishwasher.
    2. This error points to a problem with a motorized lower spray arm. Access the sump area by removing the lower rack and filter assembly.
    3. Check the wiring to the lower spray arm motor for any loose or damaged connections.
    4. If the wiring is good, the motor itself has likely failed.
    5. The motor is part of the sump assembly and will need to be uninstalled and replaced.
    6. Reassemble the sump and restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error Clean Light Stays On

    How to Fix Kenmore Dishwasher Error Clean Light Stays On

    Problem: Door switch assembly stuck; dishwasher won’t start new cycle until door opened after previous cycle

    How to Fix Clean Light Stays On Error

    1. Open the dishwasher door completely to reset the control panel.
    2. Close the door firmly.
    3. The dishwasher should now be ready to start a new cycle. This issue occurs when the door isn’t opened after the previous cycle finishes.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error Console Light Blinks Rapidly

    How to Fix Kenmore Dishwasher Error Console Light Blinks Rapidly

    Problem: Stuck button detected on control panel

    How to Fix Console Light Blinks Rapidly Error

    1. Disconnect the dishwasher from power at the circuit breaker.
    2. Open the dishwasher door and remove the screws holding the inner door panel to access the control panel.
    3. Disconnect the ribbon cable that connects the user interface control panel to the main control board.
    4. Reconnect the power and wait to see if the error code returns. If it does not, the user interface control panel is faulty and needs to be replaced.
    5. If the error persists, the main control board is likely the issue.
    6. Replace the faulty component, reassemble the door, and restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F10E3

    How to Fix Kenmore Dishwasher Error F10E3

    Problem: Drying fan / vent failure (alternate format)

    How to Fix F10E3 Error

    1. This is an alternate code for a drying fan failure, same as code 10-
    2. Disconnect power to the dishwasher.
    3. Remove the inner door panel to access the drying fan assembly.
    4. Check the wire harness connection to the fan motor.
    5. If the connection is secure, the fan motor is faulty and must be replaced.
    6. Install the new fan assembly, reconnect wiring, and reassemble the door.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F4E1

    How to Fix Kenmore Dishwasher Error F4E1

    Problem: Communication error between control board and circulation pump motor

    How to Fix F4E1 Error

    1. Disconnect power to the dishwasher at the circuit breaker.
    2. Pull the dishwasher out from under the counter to access the circulation pump and motor assembly.
    3. Check the wire harness connection between the main control board and the circulation pump motor. Ensure it is secure and the wires are not damaged.
    4. If the wiring is intact, the circulation pump and motor assembly has likely failed and needs to be replaced.
    5. Disconnect hoses and mounting brackets, remove the old pump, and install the new one.
    6. Reconnect all hoses and wiring, slide the dishwasher back into place, and restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F5E2

    How to Fix Kenmore Dishwasher Error F5E2

    Problem: Control detects door not opening between cycles

    How to Fix F5E2 Error

    1. This error is functionally the same as code 5-
    2. The control board did not detect the door opening between cycles.
    3. Always open the door for several seconds after a cycle is complete.
    4. If the error persists, the door latch assembly’s microswitch is likely failing. Disconnect power.
    5. Disassemble the door to access the latch assembly.
    6. Test the switches with a multimeter. If a switch is faulty, replace the entire door latch assembly.
    7. Reassemble the door and restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F6E2

    How to Fix Kenmore Dishwasher Error F6E2

    Problem: Water inlet valve failure

    How to Fix F6E2 Error

    1. Shut off the water supply and electrical power to the dishwasher.
    2. The water inlet valve is usually located at the front left corner, behind the lower access panel.
    3. Place a towel under the valve to catch any water.
    4. Disconnect the water supply line and the outlet hose from the valve.
    5. Disconnect the wire harness.
    6. Remove the mounting screw(s) and replace the old valve with the new one.
    7. Reconnect hoses and wiring, turn the water supply back on, check for leaks, and then restore power.

    Recommended Parts

    As an Amazon Associate, we earn from qualifying purchases through links on this page.


    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Kenmore error codes: Kenmore Error Codes