Author: ApplianceFixGuide Team

How to Fix Samsung Dryer Error CL
Problem: Child Lock activated

How to Fix CL Error
1. The Child Lock feature has been activated, disabling most buttons.
2. To deactivate, press and hold the two specific buttons indicated on your control panel for 3 seconds. This is often a combination like ‘Temp’ and ‘Time’ or ‘Wrinkle Prevent’. Look for a small lock icon or text indicating the correct buttons.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
- Control Board
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Samsung error codes: Samsung Error Codes
March 18, 2026
How to Fix Samsung Dryer Error Cg
Problem: Vent is clogged

How to Fix Cg Error
1. Clean the lint filter screen thoroughly before or after every load.
2. Disconnect the dryer from the wall and unplug it.
3. Detach the vent hose from the back of the dryer and from the wall exhaust port.
4. Use a vent cleaning brush or a vacuum to remove all lint buildup from the entire length of the hose and the wall duct.
5. Go outside and ensure the exterior vent flap can open and close freely and is not blocked by debris.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Samsung error codes: Samsung Error Codes
March 18, 2026
How to Fix Samsung Dryer Error Clg
Problem: Vent is clogged (100%)

How to Fix Clg Error
1. This indicates a more severe blockage than the ‘Cg’ code. Unplug the dryer immediately as this is a fire hazard.
2. Detach the vent duct from the back of the dryer.
3. Thoroughly clean the entire vent path from the dryer to the outside of the house.
4. Ensure the vent flap on the exterior of your house is not stuck shut or obstructed.
5. Reattach the vent securely before using the dryer again.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
- Control Board
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Samsung error codes: Samsung Error Codes
March 18, 2026
How to Fix Samsung Dryer Error FC
Problem: Invalid power source frequency

How to Fix FC Error
1. This error indicates the control board is detecting an incorrect power frequency (e.g., 50Hz instead of 60Hz in North America). First, confirm the dryer is plugged into a dedicated 240V outlet and not an extension cord.
2. If the power source is correct, the main control board (PBA) is faulty. Shut off power at the circuit breaker.
3. Access the main control board by removing the top panel of the dryer.
4. Carefully label and disconnect all wire harnesses connected to the board.
5. Remove the mounting screws, replace the board, and securely reconnect all harnesses.
6. Reassemble the dryer and restore power.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
- Control Board
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Samsung error codes: Samsung Error Codes
March 18, 2026
How to Fix Samsung Dryer Error NC1
Problem: Lint filter problem / Check filter

How to Fix NC1 Error
1. First, perform a thorough cleaning of the lint filter and the slot it goes into.
2. If the error persists, the lint filter sensor is likely coated in residue from fabric softener sheets. Unplug the dryer.
3. The sensor is typically two metal strips located in the lint filter housing. Gently scrub these strips with a soft brush and rubbing alcohol.
4. If cleaning does not resolve the issue, the sensor itself may have failed. It may require replacing the entire lint filter housing assembly.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Samsung error codes: Samsung Error Codes
March 18, 2026
How to Fix Samsung Dryer Error Od
Problem: Excessive dry time

How to Fix Od Error
1. This error means the dryer is taking too long to dry. The most common cause is a clogged vent. First, perform a full vent cleaning from the dryer to the outside.
2. If the vent is clear, disconnect power from the dryer before proceeding.
3. The thermistor may be faulty. Test its resistance with a multimeter. It should be around 10,000 ohms at room temperature.
4. If the thermistor is good, the heating element may be partially burned out. Test the element for continuity. If it fails, it needs to be replaced.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Samsung error codes: Samsung Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error 10-3
Problem: Drying fan failure

How to Fix 10-3 Error
1. Disconnect power to the dishwasher.
2. The drying fan is typically located in the door assembly. You will need to remove the inner door panel to access it.
3. Locate the fan motor assembly and check its wire harness for a secure connection.
4. If the connection is good, the fan motor is likely faulty and needs to be replaced.
5. Remove the old fan assembly, install the new one, and reconnect the wiring.
6. Reassemble the door and restore power.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
- Motor
- Control Board
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error 5-1
Problem: Door switch failure

How to Fix 5-1 Error
1. Turn off the circuit breaker for the dishwasher.
2. Open the dishwasher door and locate the door latch assembly at the top of the tub frame.
3. Remove the screws holding the inner door panel to access the latch mechanism.
4. Disconnect the wire harness connected to the door latch assembly.
5. Remove the screws mounting the old latch assembly, install the new one, and reconnect the wiring.
6. Reassemble the door panel and restore power to test.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
- Control Board
- Switch
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error 5-2
Problem: Control detects door not opening between cycles

How to Fix 5-2 Error
1. This error indicates the control board did not register the door being opened between cycles. First, ensure you are opening the door for at least 5 seconds after a cycle completes.
2. If the problem continues, the door latch assembly’s microswitch may be faulty. Turn off power at the circuit breaker.
3. Access the door latch assembly by removing the inner door panel.
4. Test the microswitches on the latch assembly for continuity with a multimeter as you open and close the latch. If a switch fails, replace the entire door latch assembly.
5. Reassemble and restore power.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
- Control Board
- Switch
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026
How to Fix Kenmore Dishwasher Error 7-1
Problem: Heater circuit failure; no expected water temperature rise

How to Fix 7-1 Error
1. Disconnect the dishwasher from power.
2. Remove the lower access panels to get to the components under the tub.
3. Locate the hi-limit thermostat, a small device mounted on the bottom of the tub. Test it for continuity with a multimeter; it should have a closed circuit (near zero ohms) at room temperature. If it’s open, replace it.
4. If the thermostat is good, test the heating element for continuity (should be 10-30 ohms). If the element is open or shorted, replace it.
5. Check wiring between the thermostat, element, and control board for damage. If all components and wiring are good, the control board has a faulty relay and must be replaced.
Recommended Parts

As an Amazon Associate, we earn from qualifying purchases through links on this page.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Kenmore error codes: Kenmore Error Codes
March 18, 2026