Author: ApplianceFixGuide Team

  • How to Fix Maytag Dishwasher Error 7-1

    How to Fix Maytag Dishwasher Error 7-1

    Problem: Heating Element Doesn’t Work

    How to Fix 7-1 Error

    1. Disconnect the dishwasher from power at the circuit breaker.
    2. Access the heating element from the front-bottom of the dishwasher by removing the lower panels.
    3. Disconnect the wires from the heating element terminals.
    4. Use a multimeter to test the element for continuity. A good element will have a resistance reading (typically 10-30 ohms). An open circuit (infinite ohms) means the element is bad.
    5. If the element is bad, remove the nuts holding it in place and replace it with the new one.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error 7-2

    How to Fix Maytag Dishwasher Error 7-2

    Problem: Heating Element Won’t Shut Off

    How to Fix 7-2 Error

    1. DANGER: This is a serious safety issue. Immediately shut off power to the dishwasher at the circuit breaker to prevent overheating.
    2. This error means a relay on the main control board is stuck, continuously sending power to the heating element.
    3. The main control board must be replaced. It is usually located at the base of the dishwasher.
    4. Access the board, carefully transfer all wire connections to the new board, and install it.
    5. Reassemble and restore power.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error 8-4

    How to Fix Maytag Dishwasher Error 8-4

    Problem: Temperature Sensor Fault

    How to Fix 8-4 Error

    1. Disconnect the dishwasher from power.
    2. In many Maytag models, the temperature sensor (thermistor) is integrated into the main control board and is not a separate, replaceable part.
    3. If you receive this error, it means the main control board has a fault and the entire board needs to be replaced.
    4. Access the main control board at the base of the unit, transfer the wiring to the new board, and install it.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error 8-5

    How to Fix Maytag Dishwasher Error 8-5

    Problem: Water Circulation Pump Issue

    How to Fix 8-5 Error

    1. Disconnect the dishwasher from power.
    2. This error points to a failure of the main wash motor / circulation pump.
    3. You will need to pull the dishwasher out and lay it on its back to access the motor from underneath.
    4. Disconnect the hoses and wire harnesses connected to the motor assembly.
    5. Unbolt the old motor and install the new one.
    6. Reconnect all hoses and wiring securely before setting the dishwasher upright and reinstalling.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error E15

    How to Fix Maytag Dishwasher Error E15

    Problem: Leak Detection / Flood Protection Active

    How to Fix E15 Error

    1. Disconnect the dishwasher from power and shut off the water supply. This error indicates water has leaked into the base pan and activated the flood switch.
    2. Pull the dishwasher out from under the counter. Tilt it forward at a 45-degree angle to drain the water from the base pan into a towel.
    3. You must find and fix the source of the leak. Common culprits are a cracked drain pump, a loose hose connection, or a bad door seal.
    4. Inspect the drain pump and float switch for damage. The float switch can be tested for continuity; it should be open when down and closed when lifted. Replace any faulty parts.
    5. Once the leak is repaired and the base pan is dry, reassemble and restore power.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error F4E3

    How to Fix Maytag Dishwasher Error F4E3

    Problem: Restricted Drain / Drain Check Valve Fault

    How to Fix F4E3 Error

    1. Disconnect the dishwasher from power.
    2. This error indicates a problem with the drain check valve, which is part of the wash motor/circulation pump assembly.
    3. You will need to pull the dishwasher out and likely turn it on its back or side to access the wash motor from underneath.
    4. Disconnect the hoses and wire harnesses from the wash motor assembly.
    5. Unbolt and remove the entire motor assembly. The check valve is an internal component, so the standard repair is to replace the whole wash motor unit.
    6. Install the new motor, reconnect all hoses and wiring, and reassemble.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error F6E3

    How to Fix Maytag Dishwasher Error F6E3

    Problem: Wrong User Interface Installed / Communication Error

    How to Fix F6E3 Error

    1. Disconnect the dishwasher from power.
    2. This error means the main control board and the user interface are not the correct matched pair for the model. This can happen after a repair with the wrong part.
    3. Verify the part numbers of both the main control board (usually at the base) and the user interface (in the door/console).
    4. Order and install the correct, matching component(s) for your specific dishwasher model number.
    5. Replacing either board involves accessing it, carefully swapping wire harnesses, and reassembling.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error F6E4

    How to Fix Maytag Dishwasher Error F6E4

    Problem: Water Supply Tap Closed / Communication Error

    How to Fix F6E4 Error

    1. First, check the simple solution: ensure the water supply valve under your sink is turned on fully.
    2. If the water is on, the float switch may be stuck in the ‘up’ (full) position. Open the dishwasher and find the plastic float dome in the bottom of the tub. Lift it up and down a few times to ensure it moves freely.
    3. If it’s stuck, clean any debris from around the float stem.
    4. If it moves freely but the error persists, the float switch itself has failed. Disconnect power, access the switch from underneath the tub, and replace it.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error F8E2

    How to Fix Maytag Dishwasher Error F8E2

    Problem: Low Water Level / Water Softener Fault

    How to Fix F8E2 Error

    1. This error can indicate a low water level or a fault in the water softener system (if your model has one).
    2. First, ensure proper water supply as described in the ‘6-1’ error. Check that the inlet valve is working.
    3. If the water level is fine, the error may relate to the drain pump not clearing water properly, causing a sensor misread. Check the drain path for clogs.
    4. If your model has a water softener, check the salt level and ensure the reservoir cap is tight. A fault in the softener’s regeneration cycle can trigger this error, which may require replacing the drain pump or other softener components.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dishwasher Error H2O

    How to Fix Maytag Dishwasher Error H2O

    Problem: Water Supply Issue / Low Water Level

    How to Fix H2O Error

    1. This is an informational code, not an error. It means the dishwasher has detected a low water level.
    2. Make sure the water supply valve to the dishwasher is turned on completely.
    3. Check that the inlet hose is not kinked or frozen.
    4. Run the hot water at your kitchen sink for a minute before starting the dishwasher to ensure hot water is readily available.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Maytag error codes: Maytag Error Codes