Maytag Dryer error code
Maytag Dryer Error F3E5
Disconnect power and remove rear panel.
Disconnect power and remove rear panel.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Disconnect power and remove rear panel
Disconnect power and remove rear panel.
- 2Test BOTH inlet and exhaust thermistors per F3E1/F3E3
Test BOTH inlet and exhaust thermistors per F3E1/F3E3 procedures to rule out sensor failure.
- 3If both thermistors test within specification (10k±2k ohms
If both thermistors test within specification (10k±2k ohms at room temp), fault lies in control board circuitry.
A quick explanation
What does F3E5 mean?
Disconnect power and remove rear panel.
The answer you came for
How to fix Maytag dryer error F3E5
Start with the safest checks and work from simple to technical.
- 1
Disconnect power and remove rear panel
Disconnect power and remove rear panel.
- 2
Test BOTH inlet and exhaust thermistors per F3E1/F3E3
Test BOTH inlet and exhaust thermistors per F3E1/F3E3 procedures to rule out sensor failure.
- 3
If both thermistors test within specification (10k±2k ohms
If both thermistors test within specification (10k±2k ohms at room temp), fault lies in control board circuitry.
- 4
Inspect control board WPW10111608 for visible damage near
Inspect control board WPW10111608 for visible damage near thermistor input circuits: burnt components, leaking capacitors, or cold solder joints around sensor connector pins.
- 5
Check wiring harness between thermistors and board for
Check wiring harness between thermistors and board for damage—repair any broken wires with high-temperature wire nuts.
- 6
If harness intact and sensors good but error
If harness intact and sensors good but error persists, ADC (analog-to-digital converter) circuit on board has failed.
- 7
Control board cannot be economically repaired—replace WPW10111608 assembly
Control board cannot be economically repaired—replace WPW10111608 assembly.
- 8
During installation, ensure all sensor harness connectors are
During installation, ensure all sensor harness connectors are fully seated before powering on.
- 9
After replacement, run diagnostic mode to verify both
After replacement, run diagnostic mode to verify both thermistor readings display correctly and track temperature changes during test cycle.
Read the additional checks from the current guide
How to Fix Dryer Error Disconnect power and remove rear panel.Test BOTH inlet and exhaust thermistors per F3E1/F3E3 procedures to rule out sensor failure.If both thermistors test within specification (10k±2k ohms at room temp), fault lies in control board circuitry.Inspect control board WPW10111608 for visible damage near thermistor input circuits: burnt components, leaking capacitors, or cold solder joints around sensor connector pins.Check wiring harness between thermistors and board for damage—repair any broken wires with high-temperature wire nuts.If harness intact and sensors good but error persists, ADC (analog-to-digital converter) circuit on board has failed.Control board cannot be economically repaired—replace WPW10111608 assembly.During installation, ensure all sensor harness connectors are fully seated before powering on.After replacement, run diagnostic mode to verify both thermistor readings display correctly and track temperature changes during test cycle. As an Amazon Associate, we earn from qualifying purchases through links on this page.
Recommended part
Recommended part for this error code
Part listed in the current guide
OEM candidate: WPW10111608
Price noted in the current guide: $220
Why this part is shown: It is associated with Maytag Dryer error F3E5 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dryer?
If repairing this dryer no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$599
Budget-friendly dryers in the $0-$599 range.
Shop Value Options on AmazonBest Overall
$600-$999
Balanced dryers in the $600-$999 range.
Shop Best Overall Options on AmazonPremium
$1,000-$2,500
Higher-end dryers in the $1,000-$2,500 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Maytag Dryer Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.